Publications

Abstract not provided.

As modern gasoline direct injection (GDI) engines utilize sophisticated injection strategies, a detailed understanding of the air-fuel mixing process is crucial to further improvements in engine emission and fuel economy. In this study, a comprehensive evaluation of the spray process of single-component iso-octane (IC8) and multi-component gasoline surrogate E00 (36 % n-pentane, 46 % iso-octane, and 18 % n-undecane, by volume) fuels was conducted using an Engine Combustion Network (ECN) Spray G injector. High-speed extinction, schlieren, and microscopy imaging campaigns were carried out under engine-like ambient conditions in a spray vessel. Experimental results including liquid/vapor penetration, local liquid volume fraction, droplet size, and projected liquid film on the nozzle tip were compared under ECN G1 (573 K, 3.5 kg/m3), G2 (333 K, 0.5 kg/m3), and G3 (333 K, 1.01 kg/m3) conditions. In addition to the experiments, preferential evaporation process of the E00 fuel was elucidated by Large–Eddy Simulations (LES). The three-dimensional liquid volume fraction measurement enabled by the computed tomographic reconstruction showed substantial plume collapse for E00 under the G2 and G3 conditions having wider plume growth and plume-to-plume interaction due to the fuel high vapor pressure. The CFD simulation of E00 showed an inhomogeneity in the way fuel components vaporized, with more volatile components carried downstream in the spray after the end of injection. The high vapor pressure of E00 also results in ∼4 μm smaller average droplet diameter than IC8, reflecting a higher rate of initial vaporization even though the final boiling point temperature is higher. Consistent with high vapor pressure, E00 had a wider plume cone angle and enhanced interaction with the wall to cover the entire surface of the nozzle tip in a film. However, the liquid fuel underwent faster evaporation, so the final projected tip wetting area was smaller than the IC8 under the flash-boiling condition.

Abstract not provided.

Abstract not provided.

Abstract not provided.

A predictive thermodynamic model is utilized for the calculation of fuel properties of oxymethylene dimethyl ethers (OME_3–4), surrogates for gasoline, diesel and aviation fuel, as well as alcohol blends with gasoline and diesel. The alcohols used for these blends are methanol, ethanol, propanol, butanol and pentanol; their mixing ratio ranges from 10 to 50% by volume. The model is based on the Perturbed-Chain Statistical Association Fluid Theory (PC-SAFT) equation of state (EoS) and Vapor Liquid Equilibrium (VLE) calculations at constant temperature, density and composition. The model includes the association term, with the assumption of two association sites (2B scheme), to enable the modeling of alcohols. The pure-component parameters are estimated based on the Group Contribution (GC) method of various sources, as well as a parametrization model specifically designed for the case of OME_3–4. The results of the computational model for the density, vapor pressure and distillation curves at various conditions, including high-pressure, high-temperature (HPHT), are compared to experimental and computational data available in the literature. In the cases where no measurements are available for the surrogates, experimental data for the corresponding target fuel are used, taking into consideration the inherent deviation in properties between real and surrogate fuel. Overall, the results are in good agreement with the data from the literature, with the average deviation not exceeding 12% for temperature (Kelvin) on the distillation curves, 10% for density and 46% for vapor pressure and the general trend being captured successfully. The use of different pure component parameter estimation techniques can further improve the prediction quality in the cases of OME3–4 and the aviation fuel surrogate, especially for the vapor pressure, leading to an average deviation lower than 18%. These results demonstrate the predictive capabilities of the model, which extend to a wide range of fuel types and pressure/temperature conditions. Through this investigation, the present work aims to establish the limits of applicability of this thermodynamic property prediction methodology.

In recent years, the Engine Combustion Network (ECN) has developed as a worldwide reference for understanding and describing engine combustion processes, successfully bringing together experimental and numerical efforts. Since experiments and numerical simulations both target the same boundary conditions, an accurate characterization of the stratified environment that is inevitably present in experimental facilities is required. The difference between the core-, and pressure-derived bulk-temperature of pre-burn combustion vessels has been addressed in various previous publications. Additionally, thermocouple measurements have provided initial data on the boundary layer close to the injector nozzle, showing a transition to reduced ambient temperatures. The conditions at the start of fuel injection influence physicochemical properties of a fuel spray, including near nozzle mixing, heat release computations, and combustion parameters. To address the temperature stratification in more detail, thermocouple measurements at larger distances from the spray axis have been conducted. Both the temperature field prior to the pre-combustion event that preconditions the high-temperature, high-pressure ambient, as well as the stratification at the moment of fuel injection were studied. To reveal the cold boundary layer near the injector with a better spatial resolution, Rayleigh scattering experiments and thermocouple measurements at various distances close to the nozzle have been carried out. The impact of the boundary layers and temperature stratification are illustrated and quantified using numerical simulations at Spray A conditions. Next to a reference simulation with a uniform temperature field, six different stratified temperature distributions have been generated. These distributions were based on the mean experimental temperature superimposed by a randomized variance, again derived from the experiments. The results showed that an asymmetric flame structure arises in the computed results when the temperature stratification input is used. In these predictions, first-stage ignition is advanced by 24μs, while second-stage ignition is delayed by 11μs. At the same time a lift-off length difference between the top and the bottom of up to 1.1 mm is observed. Furthermore, the lift-off length is less stable over time. Given the shown dependency, the temperature data is made available along with the vessel geometry data as a recommended basis for future numerical simulations.

Abstract not provided.

Fireballs produced from the detonation of high explosives often contain particulates primarily composed of various phases of carbon soot. The transport and concentration of these particulates is of interest for model validation and emission characterization. This work proposes ultra-high-speed imaging techniques to observe a fireball's structure and optical depth. An extinction-based diagnostic applied at two wavelengths indicates that extinction scales inversely with wavelength, consistent with particles in the Rayleigh limit and dimensionless extinction coefficients which are independent of wavelength. Within current confidence bounds, the extinction-derived soot mass concentrations agree with expectations based upon literature reported soot yields. Results also identify areas of high uncertainty where additional work is recommended.

This work investigates the low- and high-temperature ignition and combustion processes, applied to the Engine Combustion Network Spray A flame, combining advanced optical diagnostics and large-eddy simulations (LES). Simultaneous high-speed (50 kHz) formaldehyde (CH2O) planar laser-induced fluorescence (PLIF) and line-of-sight OH* chemiluminescence imaging were used to measure the low- and high-temperature flame, during ignition as well as during quasi-steady combustion. While tracking the cool flame at the laser sheet plane, the present experimental setup allows detection of distinct ignition spots and dynamic fluctuations of the lift-off length over time, which overcomes limitations for flame tracking when using schlieren imaging [Sim et al.Proc. Combust. Inst. 38 (4) (2021) 5713–5721]. After significant development to improve LES prediction of the low-and high-temperature flame position, both during the ignition processes and quasi-steady combustion, the simulations were analyzed to gain understanding of the mixture variance and how this variance affects formation/consumption of CH2O. Analysis of the high-temperature ignition period shows that a key improvement in the LES is the ability to predict heterogeneous ignition sites, not only in the head of the jet, but in shear layers at the jet edge close to the position where flame lift-off eventually stabilizes. The LES analysis also shows concentrated pockets of CH2O, in the center of jet and at 20 mm downstream of the injector (in regions where the equivalence ratio is greater than 6), that are of similar length scale and frequency as the experiment (approximately 5–6 kHz). The periodic oscillation of CH2O match the frequency of pressure waves generated during auto-ignition and reflected within the constant-volume vessel throughout injection. The ability of LES to capture the periodic appearance and destruction of CH2O is particularly important because these structures travel downstream and become rich premixed flames that affect soot production.

Abstract not provided.

Imaging using THz waves has been a promising option for penetrative measurements in environments that are opaque to visible wavelengths. However, available THz imaging systems have been limited to relatively low frame rates and cannot be applied to study fast dynamics. This work explores the use of upconversion imaging techniques based on nonlinear optics to enable wavelength-flexible high frame rate THz imaging. UpConversion Imaging (UCI) uses nonlinear conversion techniques to shift the THz wavelengths carrying a target image to shorter visible or near-IR wavelengths that can be detected by available high-speed cameras. This report describes the analysis methodology used to design a prototype high-rate THz UCI system and gives a detailed explanations of the design choices that were made. The design uses a high-rate pulse-burst laser system to pump both THz generation and THz upconversion detection, allowing for scaling to acquisition rates in excess of 10 kHz. The design of the prototype system described in this report has been completed and all necessary materials have been procured. Assembly and characterization testing is on-going at the submission of this report. This report proposes future directions for work on high-rate THz UCI and potential applications of future systems.

Wall impingement and fuel film deposition in gasoline direct injection engines under cold start conditions are major concerns for emissions reduction. However, it is challenging to study the dynamics of film deposition under realistic conditions because of the difficulty of measuring the thicknesses of these microscale films. Low-coherence interferometry provides a quantitative optical film thickness measurement technique that can be applied to study this problem. This work presents the first high-speed spectral low-coherence interferometry measurements of impinging gasoline direct injection sprays. The feasibility and practical concerns associated with high-speed low-coherence interferometry systems are explored. Two approaches to spectral low-coherence interferometry: Michelson interferometry and Fizeau interferometry, were implemented and are compared. The results show that Fizeau interferometry is the better option for measurements of impinging sprays in closed spray vessels. The high-speed low-coherence interferometry system was applied in the Fizeau configuration to measure time-resolved film thickness of impinging sprays under engine-relevant conditions to demonstrate its capabilities.

Abstract not provided.

Injector performance in gasoline Direct-Injection Spark-Ignition (DISI) engines is a key focus in the automotive industry as the vehicle parc transitions from Port Fuel Injected (PFI) to DISI engine technology. DISI injector deposits, which may impact the fuel delivery process in the engine, sometimes accumulate over longer time periods and greater vehicle mileages than traditional combustion chamber deposits (CCD). These higher mileages and longer timeframes make the evaluation of these deposits in a laboratory setting more challenging due to the extended test durations necessary to achieve representative in-use levels of fouling. The need to generate injector tip deposits for research purposes begs the questions, can an artificial fouling agent to speed deposit accumulation be used, and does this result in deposits similar to those formed naturally by market fuels? In this study, a collection of DISI injectors with different types of conditioning, ranging from controlled engine-stand tests with market or profould fuels, to vehicle tests run over drive cycles, to uncontrolled field use, were analyzed to understand the characteristics of their injector tip deposits and their functional impacts. The DISI injectors, both naturally and profouled, were holistically evaluated for their spray performance, deposit composition, and deposit morphology relative to one another. The testing and accompanying analysis reveals both similarities and differences among naturally fouled, fouled through long time periods with market fuel, and profouled injectors, fouled artificially through the use of a sulfur dopant. Profouled injectors were chemically distinct from naturally fouled injectors, and found to contain higher levels of sulfur dioxide. Also, profouled injectors exhibited greater volumes of deposits on the face of the injector tip. However, functionally, both naturally-fouled and profouled injectors featured similar impacts on their spray performance relative to clean injectors, with the fouled injector spray plumes remaining narrower, limiting plume-to-plume interactions, and altering the liquid-spray penetration dynamics., insights from which can guide future research into injector tip deposits.

Current state-of-the-art gasoline direct-injection (GDI) engines use multiple injections as one of the key technologies to improve exhaust emissions and fuel efficiency. For this technology to be successful, secured adequate control of fuel quantity for each injection is mandatory. However, nonlinearity and variations in the injection quantity can deteriorate the accuracy of fuel control, especially with small fuel injections. Therefore, it is necessary to understand the complex injection behavior and to develop a predictive model to be utilized in the development process. This study presents a methodology for rate of injection (ROI) and solenoid voltage modeling using artificial neural networks (ANNs) constructed from a set of Zeuch-style hydraulic experimental measurements conducted over a wide range of conditions. A quantitative comparison between the ANN model and the experimental data shows that the model is capable of predicting not only general features of the ROI trend, but also transient and non-linear behaviors at particular conditions. In addition, the end of injection (EOI) could be detected precisely with a virtually generated solenoid voltage signal and the signal processing method, which applies to an actual engine control unit. A correlation between the detected EOI timings calculated from the modeled signal and the measurement results showed a high coefficient of determination.

In this work, we present a detailed implementation and validation of the droplet modeling framework proposed by Dahms and Oefelein (2016) into the engine commercial CFD software CONVERGE using the User Defined Function (UDF) interface. The model accounts for the nonlinear deformation and oscillation experienced by liquid spray droplet injected into high pressure and temperature. Lagrangian spray simulations of Engine Combustion Network (ECN) Spray A are performed. Model validation against standard experimental measurements of liquid velocity, vapor mixture fraction is conducted. To perform more rigorous model validation, new experimental measurements based on Diffused Back Illumination (DBI) are introduced. The new measurements are processed for Projected Liquid Volume (PLV), which offers as close as possible one-to-one model validation for liquid penetration while offering new insights into the spray physics. Comparison with a One-D model based on adiabatic mixing theory by Siebers (1999) and Desantes et al. (2007) are also conducted. Through these model validation exercises, it is shown that the new framework improves liquid-phase penetration predictions, following a tendency for enhanced evaporation, compared to the standard approach for both Reynolds Average Navier Stokes (RANS) and Large Eddy Simulation (LES). At the liquid length, maximum mixture fraction values predicted by the new approach are in good agreement those of an adiabatic mixing model. Qualitative analysis of the spray behaviors during the early stage of the injection process reveals that the proposed framework predicts significant increase in droplet evaporation rate with lower drop drag compared to the current standard approach.

Research on renewable and alternative fuels is crucial for improving the energy and environmental efficiency of modern gasoline internal combustion engines. To highlight the influence of fuel rheological and thermodynamic properties on phase change and atomisation processes, three types of gasoline blends were tested. More specifically, the campaign comprised a reference gasoline, an ethanol/gasoline blend (10% v/v) representative of renewable fuels, and an additised gasoline sample treated with viscoelasticity-inducing agents. High-speed imaging of the transient two-phase flow field arising in the internal geometry and the near-nozzle spray region of gasoline injectors was performed employing Diffuse Backlight Illumination. The metallic body of a commercial injector was modified to fit transparent tips realising two nozzle layouts, namely a two-hole real size model resembling the Engine Combustion Network spray G injector and an enraged replica with an offset hole. Experiments were conducted at realistic operating conditions comprising an injection pressure of 100 bar and ambient pressures in the range of 0.1–6.0 bar to cover the entire range of chamber pressures prevailing in Gasoline Direct Injection engines. The action of viscoelastic additives was verified to have a suppressive effect on in-nozzle cavitation (6% reduction in cavitation extent), while also enhancing spray atomisation at flash-boing conditions, in a manner resembling the more volatile gasoline/ethanol blends. Finally, persisting liquid ligaments were found to form after the end of injection for the additised sample, owing to the surfactant nature of the additives.

The detonation of explosives produces luminous fireballs often containing particulates such as carbon soot or remnants of partially reacted explosives. The spatial distribution of these particulates is of great interest for the derivation and validation of models. In this work, three ultra-high-speed imaging techniques: diffuse back-illumination extinction, schlieren, and emission imaging, are utilized to investigate the particulate quantity, spatial distribution, and structure in a small-scale fireball. The measurements show the evolution of the particulate cloud in the fireball, identifying possible emission sources and regions of high optical thickness. Extinction measurements performed at two wavelengths shows that extinction follows the inverse wavelength behavior expected of absorptive particles in the Rayleigh scattering regime. The estimated mass from these extinction measurements shows an average soot yield consistent with previous soot collection experiments. The imaging diagnostics discussed in the current work can provide detailed information on the spatial distribution and concentration of soot, crucial for validation opportunities in the future.

Abstract not provided.

Large-Eddy Simulations (LES) of a gasoline spray, where the mixture was ignited rapidly during or after injection, were performed in comparison to a previous experimental study with quantitative flame motion and soot formation data [SAE 2020-01-0291] and an accompanying Reynolds-Averaged Navier–Stokes (RANS) simulation at the same conditions. The present study reveals major shortcomings in common RANS combustion modeling practices that are significantly improved using LES at the conditions of the study, specifically for the phenomenon of rapid ignition in the highly turbulent, stratified mixture. At different ignition timings, benchmarks for the study include spray mixing and evaporation, flame propagation after ignition, and soot formation in rich mixtures. A comparison of the simulations and the experiments showed that the LES with Dynamic Structure turbulence were able to capture correctly the liquid penetration length, and to some extent, spray collapse demonstrated in the experiments. For early and intermediate ignition timings, the LES showed excellent agreement to the measurements in terms of flame structure, extent of flame penetration, and heat-release rate. However, RANS simulations (employing the common G-equation or well-stirred reactor) showed much too rapid flame spread and heat release, with connections to the predicted turbulent kinetic energy. With confidence in the LES for predicted mixture and flame motion, the predicted soot formation/oxidation was also compared to the experiments. The soot location was well captured in the LES, but the soot mass was largely underestimated using the empirical Hiroyasu model. An analysis of the predicted fuel–air mixture was used to explain different flame propagation speeds and soot production tendencies when varying ignition timing.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

This work describes the diagnostic implementation and image processing methods to quantitatively measure diesel spray mixing injected into a high-pressure, high-temperature environment. We used a high-repetition-rate pulse-burst laser developed in-house, a high-speed CMOS camera, and optimized the optical configuration to capture Rayleigh scattering images of the vaporized fuel jets inside a constant volume chamber. The experimental installation was modified to reduce reflections and flare levels to maximize the images’ signal-to-noise ratios by anti-reflection coatings on windows and surfaces, as well as series of optical baffles. Because of the specificities of the high-speed system, several image processing techniques had to be developed and implemented to provide quantitative fuel concentration measurements. These methods involve various correction procedures such as camera linearity, laser intensity fluctuation, dynamic background flare, as well as beam-steering effects. Image inpainting was also applied to correct the Rayleigh scattering signal from large scatterers (e.g. particulates). The experiments demonstrate that applying planar laser Rayleigh scattering at high repetition rate to quantitatively resolve the mixing of fuel and ambient gases in diesel jets is challenging, but possible. The thorough analysis of the experimental uncertainty and comparisons to past data prove that such measurements can be accurate, whilst providing valuable information about the mixing processes of high-pressure diesel jets.

All future high-efficiency engines will have fuel directly sprayed into the engine cylinder. Engine developers agree that a major barrier to the rapid development and design of these high-efficiency, clean engines is the lack of accurate fuel spray computational fluid dynamics (CFD) models. The spray injection process largely determines the fuel–air mixture processes in the engine, which subsequently drive combustion and emissions in both direct-injection gasoline and diesel systems, particularly at cold-start conditions when aftertreatment is ineffective. Engines must be tolerant to a range of fuels, and there must be an understanding of how specific fuel properties affect the spray mixing and evaporation processes to intentionally create better fuels and better injectors. More predictive spray combustion models will enable rapid design and optimization of future high-efficiency engines, providing more affordable vehicles and saving fuel.

Abstract not provided.

The interaction of multiple injections in a diesel engine facilitates a complex interplay between freshly introduced fuel, previous combustion products, and overall combustion. To improve understanding of the relevant processes, high-speed Planar Laser-Induced Fluorescence (PLIF) with 355-nm excitation of formaldehyde and Polycyclic Aromatic Hydrocarbon (PAH) soot precursors is applied to multiple injections of n-dodecane from Engine Combustion Network Spray D, characterized by a converging 189-µm nozzle. High-speed schlieren imaging is applied simultaneously with 50-kHz PLIF excitation to visualize the spray structures, jet penetration, and ignition processes. For the first injection, formaldehyde (as an indicator of low-temperature chemistry) is first found in the jet periphery, after which it quickly propagates through the center of the jet, towards the jet head prior to high-temperature ignition. At second-stage ignition, downstream formaldehyde is consumed rapidly and upstream formaldehyde develops into a quasi-steady structure for as long as the momentum flux from the injector continues. Since the first injection in this work is relatively short, differences to a single long injection are readily observed, ultimately resulting in high-temperature combustion and PAH structures appearing farther upstream after the end of injection. For the second injection in this work, the first formaldehyde signal is significantly advanced because of the entrained high-temperature combustion products, and an obvious premixed burn event does not occur. The propensity for combustion recession after the end of the first injection changes significantly with ambient temperature, thereby affecting the level of interaction between the first- and second injection.

The low- and high-temperature ignition and combustion processes in a high-pressure spray flame of n-dodecane were investigated using simultaneous 50-kHz formaldehyde (HCHO) planar laser-induced fluorescence (PLIF) and 100-kHz schlieren imaging. PLIF measurements were facilitated through the use of a pulse-burst-mode Nd:YAG laser, and the high-speed HCHO PLIF signal was imaged using a non-intensified CMOS camera with dynamic background emission correction. The experiments were conducted in the Sandia constant-volume preburn vessel equipped with a new Spray A injector. The effects of ambient conditions on the ignition delay times of the two-stage ignition events, HCHO structures, and lift-off length values were examined. Consistent with past studies of traditional Spray A flames, the formation of HCHO was first observed in the jet peripheries where the equivalence ratio (Φ) is expected to be leaner and hotter and then grows in size and in intensity downstream into the jet core where Φ is expected to be richer and colder. The measurements showed that the formation and propagation of HCHO from the leaner to richer region leads to high-temperature ignition events, supporting the identification of a phenomenon called “cool-flame wave propagation” during the transient ignition process. Subsequent high-temperature ignition was found to consume the previously formed HCHO in the jet head, while the formation of HCHO persisted in the fuel-rich zone near the flame base over the entire combustion period.

A high-speed flow visualisation set-up comprising of combined diffuse backlight illumination (DBI) and schlieren imaging has been developed to illustrate the highly transient, two-phase flow arising in a real-size optical fuel injector. The different illumination nature of the two techniques, diffuse and parallel light respectively, allows for the capturing of refractive-index gradients due to the presence of both interfaces and density gradients within the orifice. Hence, the onset of cavitation and secondary-flow motion within the sac and injector hole can be concurrently visualised. Experiments were conducted utilising a diesel injector fitted with a single-hole transparent tip (ECN spray D) at injection pressures of 700–900 bar and ambient pressures in the range of 1–20 bar. High-speed DBI images obtained at 100,000 fps revealed that the orifice, due to its tapered layout, is mildly cavitating with relatively constant cavity sheets arising mainly in regions of manufacturing imperfections. Nevertheless, schlieren images obtained at the same frame rate demonstrated that a multitude of vortices with short lifetimes arise at different scales in the sac and nozzle regions during the entire duration of the injection cycle but the vortices do not necessarily result in phase change. The magnitude and exact location of coherent vortical structures have a measurable influence on the dynamics of the spray emerging downstream the injector outlet, leading to distinct differences in the variation of its cone angle depending on the injection and ambient pressures examined.

Mitigating particulate matter (PM) emissions while simultaneously controlling nitrogen oxide and hydrocarbon emissions is critical for both gasoline and diesel engines. The problem is especially critical during cold-start cycles where aftertreatment devices are less effective. Understanding how liquid sprays and films form PM and designing to change the outcome requires advanced combustion concepts developed through joint experimental and computational efforts. However, existing spray and soot computational models are oversimplified and non-physical, and are therefore unable to reliably capture quantitative or even qualitative trends over a wide range of engine operating conditions. This task involves the development and application of advanced optical diagnostics and high-pressure gas and particle sampling/analysis in unique high-temperature, high-pressure vessels to investigate spray dynamics and soot formation with the objective of providing fundamental understanding about soot processes under relevant engine conditions to aid the development of improved soot models for commercial CFD codes

Abstract not provided.

We propose a novel approach to evaluate the relaxation time of vapor bubble growth in the context of the flash boiling of a superheated liquid. In alternative to the empirical correlation derived from superheated water experiments almost fifty years ago, the new model describes the thermally-dominated growth of vapor bubbles in terms that are dependent on the local Jakob number (the ratio of sensible heat to latent heat during phase change) and the number density of vapor bubbles. The model is tested by plugging the resulting relaxation time into the Homogenous Relaxation Model (HRM). Flash-boiling simulations carried out with HRM are compared with n-pentane (C5H12) injection and boil-off experiments conducted with a real-size, axial-hole, transparent gasoline injector discharging into a constant-pressure vessel. The long-distance microscopy images from the experiments, processed to derive the projected liquid volume (PLV) of the spray, provide a unique set of time-resolved validation data for direct fuel injection simulations. At conditions ranging from flaring to mild and minimal flash boiling, we show that switching to the new relaxation time improves the agreement with the measured PLV profiles with respect to the standard empirical model. Particularly at flaring conditions, the predicted increase in gas cooling caused by rapid vapor production is shown to be more consistent with the observed boil-off.

Abstract not provided.

The present work investigates the complex phenomena associated with pressure/high temperature dodecane injection for the Engine Combustion Network (ECN) Spray-A case, employing more elaborate thermodynamic closures, to avoid well known deficiencies concerning density and speed of sound prediction using traditional cubic models. A tabulated thermodynamic approach is proposed here, based on log10(p)-T tables, providing very high accuracy across a large range of pressures, spanning from 0 to 2500 bar, with only a small number of interpolation points. The tabulation approach is directly extensible to any thermodynamic model, existing or to be developed in the future. Here NIST REFPROP properties are used, combined with PC-SAFT Vapor-Liquid-Equilibrium to identify the liquid in mixtures penetration, hence avoiding the use of an arbitrary threshold for mass fraction. Identified liquid and vapour penetration are compared against experimental data from the ECN database showing a good agreement, within approximately 3–8% for axial penetration of liquid, 2% for vapor axial penetration and within experimental uncertainty for radial distribution of mass fraction. Analysis of the vortex evolution indicates that driving mechanisms behind the jet break-up are vortex tilting/stretching, then baroclinic torque, leading to Rayleigh-Taylor instabilities, closely followed by vortex dilation and finally viscous effects.

The flow and cavitation behavior inside fuel injectors is known to affect spray development, mixing and combustion characteristics. While diesel fuel injectors with converging and hydro-eroded holes are generally known to limit cavitation and feature higher discharge coefficients during the steady period of injection, less is known about the flow during transient periods corresponding to needle opening and closing. Multiple injection strategies involve short injections, multiplying these aspects and giving them a growing importance as part of the fuel delivery process. In this study, single-hole transparent nozzles were manufactured with the same hole inlet radius and diameter as the Engine Combustion Network Spray D nozzle, mounted to a modified version of a common-rail Spray A injector body and needle. Needle opening and closing periods were visualized with stereoscopic high-speed microscopy at injection pressures relevant to modern diesel engines. Time-resolved sac pressure was extracted via elastic deformation analysis of the transparent nozzles. Sources of cavitation were observed and tracked, enabling the identification of a gas exchange process after the end of injection with ingestion of chamber gas into the sac and orifice. We observed that the gas exchange contributed widely to disrupting the start of injection and outlet flow during the subsequent injection event.

In a collaborative effort to identify key aspects of heavy-duty diesel injector behavior, the Engine Combustion Network (ECN) Spray C and Spray D injectors were characterized in three independent research laboratories using constant volume pre-burn vessels and a heated constant-pressure vessel. This work reports on experiments with nominally identical injectors used in different optically accessible combustion chambers, where one of the injectors was designed intentionally to promote cavitation. Optical diagnostic techniques specifically targeted liquid- and vapor-phase penetration, combustion indicators, and sooting behavior over a large range of ambient temperatures—from 850 K to 1100 K. Because the large-orifice injectors employed in this work result in flame lengths that extend well beyond the optical diagnostics’ field-of-view, a novel method using a characteristic volume is proposed for quantitative comparison of soot under such conditions. Further, the viability of extrapolating these measurements downstream is considered. The results reported in this publication explain trends and unique characteristics of the two different injectors over a range of conditions and serve as calibration targets for numerical efforts within the ECN consortium and beyond. Building on agreement for experimental results from different institutions under inert conditions, apparent differences found in combustion indicators and sooting behavior are addressed and explained. Ignition delay and soot onset are correlated and the results demonstrate the sensitivity of soot formation to the major species of the ambient gas (i.e., carbon dioxide, water, and nitrogen in the pre-burn ambient versus nitrogen only in the constant pressure vessel) when holding ambient oxygen volume percent constant.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Combustion issued from an eight-hole, direct-injection spray was experimentally studied in a constant-volume pre-burn combustion vessel using simultaneous high-speed diffused back-illumination extinction imaging (DBIEI) and OH∗ chemiluminescence. DBIEI has been employed to observe the liquid-phase of the spray and to quantitatively investigate the soot formation and oxidation taking place during combustion. The fuel-air mixture was ignited with a plasma induced by a single-shot Nd:YAG laser, permitting precise control of the ignition location in space and time. OH∗ chemiluminescence was used to track the high-temperature ignition and flame. The study showed that increasing the delay between the end of injection and ignition drastically reduces soot formation without necessarily compromising combustion efficiency. For long delays between the end of injection and ignition (1.9 ms) soot formation was eliminated in the main downstream charge of the fuel spray. However, poorly atomized and large droplets formed at the end of injection (dribble) eventually do form soot near the injector even when none is formed in the main charge. The quantitative soot measurements for these spray and ignition scenarios, resolved in time and space, represents a significant new achievement. Reynolds-averaged Navier-Stokes (RANS) simulations were performed to assess spray mixing and combustion. An analysis of the predicted fuel-air mixture in key regions, defined based upon experimental observations, was used to explain different flame propagation speeds and soot production tendencies when varying ignition timing. The mixture analysis indicates that soot production can be avoided if the flame propagates into regions where the equivalence ratio (φ) is already below 2. Reactive RANS simulations have also been performed, but with a poor match against the experiment, as the flame speed and heat-release rate are largely over estimated. This modeling weakness appears related to a very high level of turbulent viscosity predicted for the high-momentum spray in the RANS simulations, which is an important consideration for modeling ignition and flame propagation in mixtures immediately created by the spray.

Abstract: The method for direct injection of fuel in the cylinder of an IC engines is important to high-efficiency and low-emission performance. Optical spray diagnostics plays an important role in understanding plume movement and interaction for multi-hole injectors, and providing baseline understanding used for computational optimization of fuel delivery. Traditional planar or line-of-sight diagnostics fail to capture the liquid distribution because of optical thickness concerns. This work proposes a high-speed (67 kHz) extinction imaging technique at various injector rotations coupled to computed tomography (CT) for time-resolved reconstruction of liquid volume fraction in three dimensions. The number of views selected and processing were based on synthetic (modeled) liquid volume fraction data where extinction and CT adequately reconstructed each plume. The exercise showed that for an 8-hole, symmetric-design injector (ECN Spray G), only three different views are enough to reproduce the direction of each plume, and particularly the mean plume direction. Therefore, the number of views was minimized for experiments to save expense. Measurements applying this limited-view technique confirm plume–plume variations also detected with mechanical patternation, while providing better spatial and temporal resolution than achieved previously. Uncertainties due to the limited view within pressurized spray chambers, the droplet size, and optically thick regions are discussed. Graphic abstract: [Figure not available: see fulltext.].

Gas ingested into the sac of a fuel injector after the injector needle valve closes is known to have crucial impacts on initial spray formation and plume growth in a following injection cycle. Yet little research has been attempted to understand the fate sac gases during pressure expansion and compression typical of an engine. This study investigated cavitation and bubble processes in the sac including the effect of chamber pressure decrease and increase consistent with an engine cycle. A single axial-hole transparent nozzle based on the Engine Combustion Network (ECN) Spray D nozzle geometry was mounted in a vessel filled with nitrogen, and the nitrogen gas pressure was cycled after the end of injection. Interior nozzle phenomena were visualized by high-speed longdistance microscopy with a nanosecond pulsed LED back-illumination. Experimental results showed that the volume of gas in the sac after the needle closes depends upon the vessel gas pressure. Higher back pressure results in less cavitation and a smaller volume of non-condensable gas in the sac. But a pressure decrease mimicking the expansion stroke causes the gas within the sac to expand significantly, proportional to the pressure decrease, while also evacuating liquid in front of the bubble. The volume of the gas in the sac increases during the expansion cycle due both to isothermal expansion as well as desorption of inherent dissolved gas in the fuel. During the compression cycle, the volume of bubbles decreases and additional non-condensable ambient gas is ingested into the sac. As the liquid fuel is nearly incompressible, the volume of both liquid and gas essentially remains constant during compression.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Time-resolved visualization of fast processes using high-speed digital video-cameras has been widely used in most fields of scientific research for over a decade. In many applications, high-speed imaging is used not only to record the time history of a phenomenon but also to quantify it, hence requiring dependable equipment. Important aspects of two-dimensional imaging instrumentation used to qualitatively or quantitatively assess fast-moving scenes include sensitivity, linearity, as well as signal-to-noise ratio (SNR). Under certain circumstances, the weaknesses of commercially available high-speed cameras, i.e., sensitivity, linearity, image lag, etc., render the experiment complicated and uncertain. Our study evaluated two advanced CMOS-based, continuous-recording, high-speed cameras available at the moment of writing. Various parameters, potentially important toward accurate time-resolved measurements and photonic quantification, have been measured under controlled conditions on the bench, using scientific instrumentation. Testing procedures to measure sensitivity, linearity, SNR, shutter accuracy, and image lag are proposed and detailed. The results of the tests, comparing the two high-speed cameras under study, are also presented and discussed. Results show that, with careful implementation and understanding of their performance and limitations, these high-speed cameras are reasonable alternatives to scientific CCD cameras, while also delivering time-resolved imaging data.

All future high-efficiency engines will have fuel directly sprayed into the engine cylinder. Engine developers agree that a major barrier to the rapid development and design of these high-efficiency, clean engines is the lack of accurate fuel spray computational fluid dynamic (CFD) models. The spray injection process largely determines the fuel-air mixture processes in the engine, which subsequently drives combustion and emissions in both direct-injection gasoline and diesel systems. More predictive spray combustion models will enable rapid design and optimization of future high-efficiency engines, providing more affordable vehicles and also saving fuel.

The DOE project for Co-Optimization of Fuels and Engines seeks to define both fuel properties and engine hardware to create cleaner and more fuel-efficient engines. Fuel spray technologies are central to this goal as the spray injection determines the combustible mixtures formed within the engine. Sprays are known to affect bum rate and efficiency, particulate formation and emissions, as well as temperature and engine knock sites. Computational fluid dynamic models must predict complicated interaction between plumes and vaporization to be useful as a design tool for industry. Changes in fuel properties are expected to affect fuel delivery. While Co-Optima fuels may be selected for chemical criteria, such as high octane number rating, an understanding of how the physical properties affect spray performance is necessary to optimize fuel delivery. Many of the selected Co-Optima fuels have properties that are different than standard gasoline, requiring investigations for their performance. A new continuous-flow spray chamber facility has been completed, offering capability to control the pressure and temperature of the gases at engine-relevant conditions at the time of injection as well as a massive increase in data throughput. Direct-injection multi-hole gasoline sprays for different Co-Optima fuels are investigated in this chamber.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The collapse or merging of individual plumes of direct-injection gasoline injectors is of fundamental importance to engine performance because of its impact on fuel-air mixing. However, the mechanisms of spray collapse are not fully understood and are difficult to predict. The purpose of this work is to study the aerodynamics in the inter-spray region, which can potentially lead to plume collapse. High-speed (100 kHz) particle image velocimetry is applied along a plane between plumes to observe the full temporal evolution of plume interaction and potential collapse, resolved for individual injection events. Supporting information along a line of sight is obtained using simultaneous diffused back illumination and Mie-scatter techniques. Experiments are performed under simulated engine conditions using a symmetric eight-hole injector in a high-temperature, high-pressure vessel at the “Spray G” operating conditions of the engine combustion network. Indicators of plume interaction and collapse include changes in counter-flow recirculation of ambient gas toward the injector along the axis of the injector or in the inter-plume region between plumes. The effect of ambient temperature and gas density on the inter-plume aerodynamics and the subsequent plume collapse are assessed. Increasing ambient temperature or density, with enhanced vaporization and momentum exchange, accelerates the plume interaction. Plume direction progressively shifts toward the injector axis with time, demonstrating that the plume interaction and collapse are inherently transient.

Abstract not provided.

The collapse or merging of individual plumes of direct-injection gasoline injectors is of fundamental importance to engine performance because of its impact on fuel-air mixing. However, the mechanisms of spray collapse are not fully understood. The purpose of this work is to study the effects of injection duration and multiple injections on the interaction and/or collapse of multi-plume GDI sprays. High-speed (100 kHz) Particle Image Velocimetry (PIV) is applied along a plane between plumes to observe the full temporal evolution of plume-interaction and potential collapse, resolved for individual injection events. Supporting information along a line of sight is obtained using Diffused Back Illumination (DBI). Experiments are performed under simulated engine conditions using a symmetric 8-hole injector in a high-temperature, high-pressure vessel at the "Spray G" operating conditions of the Engine Combustion Network (ECN). Longer injection duration is found to promote plume collapse, while staging fuel delivery with multiple, shorter injections is resistant to plume collapse.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Designers of direct-injection compression-ignition engines use a variety of strategies to improve the fuel/charge-gas mixture within the combustion chamber for increased efficiency and reduced pollutant emissions. Strategies include the use of high fuel-injection pressures, multiple injections, small injector orifices, flow swirl, long-ignition-delay conditions, and oxygenated fuels. This is the first journal publication paper on a new mixing-enhancement strategy for emissions reduction: ducted fuel injection. The concept involves injecting fuel along the axis of a small cylindrical duct within the combustion chamber, to enhance the mixture in the autoignition zone relative to a conventional free-spray configuration (i.e., a fuel spray that is not surrounded by a duct). Finally, the results described herein, from initial proof-of-concept experiments conducted in a constant-volume combustion vessel, show dramatically lower soot incandescence from ducted fuel injection than from free sprays over a range of charge-gas conditions that are representative of those in modern direct-injection compression-ignition engines.

Abstract not provided.

Abstract not provided.

A conceptual model for turbulent ignition in high-pressure spray flames is presented. The model is motivated by first-principles simulations and optical diagnostics applied to the Sandia n-dodecane experiment. The combined analysis established a conceptual model for turbulent ignition in high-pressure spray flames which is based on a set of identified characteristic time scales. The suddenly forming steep gradients from successful high-temperature ignition initiate the propagation of a turbulent flame. It rapidly ignites the entire spray head on time scales which are generally significantly smaller than the corresponding cool flame wave time scales.

Fuel and oxidizer mixing is a key parameter influencing combustion and emission performance in diesel engines. At the same time, quantitative mixing measurements in automotive sprays are very challenging such that only a few experimental results are available as targets for the development and tuning of numerical models. The caveat is that the experimental data mainly concern the quasi-steady part of the jet, while it can be argued that the injection process in current alternative thermal engines is mostly transient. This work applies planar laser Rayleigh scattering at high-frequency to resolve the development and mixing of vaporized diesel sprays injected in a highly-pressurized environment. The state-of-the-art equipment employed for these experiments include a purposely-built high-power, high-repetition rate pulsed burst laser, optimized optics and a state-of-the-art high-speed CMOS camera. Advanced image processing methods were developed and implemented to mitigate the negative effects of the extreme environments found in diesel engines at the time of injection. The experiments provided two-dimensional mean and variance of the mixture and temperature quantities. The optical system's high spatial and temporal resolution enables tracking of the mixing field with time and space, from which temporally and spatially correlated mixing quantities can be extracted. Further analysis of the detailed mixture and temperature fields offered information about the turbulent mixing process of high-pressure diesel sprays such as scalar dissipation rates or turbulent length scales. Substantial effort was made to assess the uncertainties and limitations of such experimental results due to the optically challenging environment.

Designers of direct-injection compression-ignition engines use a variety of strategies to improve the fuel/charge-gas mixture within the combustion chamber for increased efficiency and reduced pollutant emissions. Strategies include the use of high fuel-injection pressures, multiple injections, small injector orifices, flow swirl, long-ignition-delay conditions, and oxygenated fuels. This is the first journal publication on a new mixing-enhancement strategy for emissions reduction: ducted fuel injection. The concept involves injecting fuel along the axis of a small cylindrical duct within the combustion chamber, to enhance the mixture in the autoignition zone relative to a conventional free-spray configuration (i.e., a fuel spray that is not surrounded by a duct). The results described herein, from initial proof-of-concept experiments conducted in a constant-volume combustion vessel, show dramatically lower soot incandescence from ducted fuel injection than from free sprays over a range of charge-gas conditions that are representative of those in modern direct-injection compression-ignition engines.

Whilst the physics of both classical evaporation and supercritical fluid mixing are reasonably well characterized and understood in isolation, little is known about the transition from one to the other in the context of liquid fuel systems. The lack of experimental data for microscopic droplets at realistic operating conditions impedes the development of phenomenological and numerical models. To address this issue we performed systematic measurements using high-speed long-distance microscopy, for three single-component fuels (n-heptane, n-dodecane, n-hexadecane), into gas at elevated temperatures (700–1200 K) and pressures (2–11 MPa). We describe these high-speed visualizations and the time evolution of the transition from liquid droplet to fuel vapour at the microscopic level. The measurements show that the classical atomization and vaporisation processes do shift to one where surface tension forces diminish with increasing pressure and temperature, but the transition to diffusive mixing does not occur instantaneously when the fuel enters the chamber. Rather, subcritical liquid structures exhibit surface tension in the near-nozzle region and then, after time surrounded by the hot ambient gas and fuel vapour, undergo a transition to a dense miscible fluid. Although there was clear evidence of surface tension and primary atomization for n-dodecane and n-hexadecane for a period of time at all the above conditions, n-heptane appeared to produce a supercritical fluid from the nozzle outlet when injected at the most elevated conditions (1200 K, 10 MPa). This demonstrates that the time taken by a droplet to transition to diffusive mixing depends on the pressure and temperature of the gas surrounding the droplet as well as the fuel properties. We summarise our observations into a phenomenological model which describes the morphological evolution and transition of microscopic droplets from classical evaporation through a transitional mixing regime and towards diffusive mixing, as a function of operating conditions. We provide criteria for these regime transitions as reduced pressure–temperature correlations, revealing the conditions where transcritical mixing is important to diesel fuel spray mixing.

Abstract not provided.

This work explores the mechanisms by which a post injection can reduce unburned hydrocarbon (UHC) emissions in heavy-duty diesel engines operating at low-temperature combustion conditions. Post injections, small, close-coupled injections of fuel after the main injection, have been shown to reduce UHC in the authors’ previous work. In this work, we analyze optical data from laser-induced fluorescence of both CH₂O and OH and use chemical reactor modeling to better understand the mechanism by which post injections reduce UHC emissions. The results indicate that post-injection efficacy, or the extent to which a post injection reduces UHC emissions, is a strong function of the cylinder pressure variation during the post injection. However, the data and analysis indicate that the pressure and temperature rise from the post injection combustion cannot solely explain the UHC reduction measured by both engine-out and optical diagnostics. In conclusion, the fluid-mechanic, thermal, and chemical interaction of the post injection with the main-injection mixture is a key part of UHC reduction; the starting action of the post jet and the subsequent entrainment of surrounding gases are likely both important processes in reducing UHC with a post injection.

Abstract not provided.

An n-dodecane spray flame (Spray A from Engine Combustion Network) was simulated using a δ function combustion model along with a dynamic structure large eddy simulation (LES) model to evaluate its performance at engine-relevant conditions and to understand the transient behavior of this turbulent flame. The liquid spray was treated with a traditional Lagrangian method and the gas-phase reaction was modeled using a δ function combustion model. A 103-species skeletal mechanism was used for the n-dodecane chemical kinetic model. Significantly different flame structures and ignition processes are observed for the LES compared to those of Reynolds-averaged Navier-Stokes (RANS) predictions. The LES data suggests that the first ignition initiates in a lean mixture and propagates to a rich mixture, and the main ignition happens in the rich mixture, preferably less than 0.14 in mixture fraction space. LES was observed to have multiple ignition spots in the mixing layer simultaneously while the main ignition initiates in a clearly asymmetric fashion. The temporal flame development also indicates the flame stabilization mechanism is auto-ignition controlled. Soot predictions by LES present much better agreement with experiments compared to RANS, both qualitatively and quantitatively. Multiple realizations for LES were performed to understand the realization to realization variation and to establish best practices for ensemble-averaging diesel spray flames. The relevance index analysis suggests that an average of 5 and 6 realizations can reach 99% of similarity to the target average of 16 realizations on the mixture fraction and temperature fields, respectively. However, more realizations are necessary for the hydroxide (OH) and soot mass fractions due to their high fluctuations.

Abstract not provided.

Abstract not provided.

In this LDRD project, we developed a capability for quantitative high - speed imaging measurements of high - pressure fuel injection dynamics to advance understanding of turbulent mixing in transcritical flows, ignition, and flame stabilization mechanisms, and to provide e ssential validation data for developing predictive tools for engine combustion simulations. Advanced, fuel - efficient engine technologies rely on fuel injection into a high - pressure, high - temperature environment for mixture preparation and com bustion. Howe ver, the dynamics of fuel injection are not well understood and pose significant experimental and modeling challenges. To address the need for quantitative high - speed measurements, we developed a Nd:YAG laser that provides a 5ms burst of pulses at 100 kHz o n a robust mobile platform . Using this laser, we demonstrated s patially and temporally resolved Rayleigh scattering imaging and particle image velocimetry measurements of turbulent mixing in high - pressure gas - phase flows and vaporizing sprays . Quantitativ e interpretation of high - pressure measurements was advanced by reducing and correcting interferences and imaging artifacts.

Abstract not provided.

We investigate the mixing, penetration, and ignition characteristics of high-pressure n-dodecane sprays having a split injection schedule (0.5/0.5 dwell/0.5 ms) in a pre-burn combustion vessel at ambient temperatures of 750 K, 800 K and 900 K. High-speed imaging techniques provide a time-resolved measure of vapor penetration and the timing and progression of the first- and second-stage ignition events. Simultaneous single-shot planar laser-induced fluorescence (PLIF) imaging identifies the timing and location where formaldehyde (CH2O) is produced from first-stage ignition and consumed following second-stage ignition. At the 900-K condition, the second injection penetrates into high-temperature combustion products remaining in the near-nozzle region from the first injection. Consequently, the ignition delay for the second injection is shorter than that of the first injection (by a factor of two) and the second injection ignites at a more upstream location near the liquid length. At the 750 K and 800 K conditions, high-temperature ignition does not occur in the near-nozzle region after the end of the first injection, though formaldehyde remains from first-stage reactions. Under these conditions, the second injection penetrates into cool-flame products that are slightly elevated in temperature (∼100 K) relative to the ambient. This modest temperature increase and the availability of reactive cool-flame products reduces the first- and second-stage ignition delay of the second injection by a factor of approximately two relative to the first injection. At the 750-K ambient condition, high-temperature ignition of the first injection does not occur until the second injection enriches the very fuel-lean downstream regions.

Abstract not provided.

Abstract not provided.

The development of accurate predictive engine simulations requires experimental data to both inform and validate the models, but very limited information is presently available about the chemical structure of high pressure spray flames under engine- relevant conditions. Probing such flames for chemical information using non- intrusive optical methods or intrusive sampling techniques, however, is challenging because of the physical and optical harshness of the environment. This work details two new diagnostics that have been developed and deployed to obtain quantitative species concentrations and soot volume fractions from a high-pressure combusting spray. A high-speed, high-pressure sampling system was developed to extract gaseous species (including soot precursor species) from within the flame for offline analysis by time-of-flight mass spectrometry. A high-speed multi-wavelength optical extinction diagnostic was also developed to quantify transient and quasi-steady soot processes. High-pressure sampling and offline characterization of gas-phase species formed following the pre-burn event was accomplished as well as characterization of gas-phase species present in the lift-off region of a high-pressure n-dodecane spray flame. For the initial samples discussed in this work several species were identified, including polycyclic aromatic hydrocarbons (PAH); however, quantitative mole fractions were not determined. Nevertheless, the diagnostic developed here does have this capability. Quantitative, time-resolved measurements of soot extinction were also accomplished and the novel use of multiple incident wavelengths proved valuable toward characterizing changes in soot optical properties within different regions of the spray flame.

Abstract not provided.

Quantitative measurements of the total radiative heat transfer from high-pressure diesel spray flames under a range of conditions will enable engine modelers to more accurately understand and predict the effects of advanced combustion strategies on thermal loads and efficiencies. Moreover, the coupling of radiation heat transfer to soot formation processes and its impact on the temperature field and gaseous combustion pollutants is also of great interest. For example, it has been shown that reduced soot formation in diesel engines can result in higher flame temperatures (due to less radiative cooling) leading to greater NOx emissions. Whereas much of the previous work in research engines has evaluated radiation based on two- or three-color detection with limited spatial resolution, this work uses an imaging spectrometer in conjunction with a constant volume pre-burn vessel to quantify soot temperatures, optical thickness, and total radiation with spatial and spectral (360-700 nm) resolution along the flame axis. Sprays of n-dodecane were injected from a single hole, 90-m diameter orifice into a range of ambient temperature conditions while holding ambient density and oxygen concentration constant at 22.8 kg/m 3 and 15%, respectively. Soot surface temperatures derived by fitting a model to the spectral data were within 10 K of the stoichiometric computed adiabatic flame temperature for lower ambient temperature, lower sooting cases. As ambient temperature was increased, leading to greater soot formation, the spectrally derived peak soot temperature decreased relative to the calculated adiabatic flame temperature. For the highest ambient temperature case (1200 K), the spectrally derived soot surface temperature was more than 140 K lower than the calculated adiabatic flame temperature. Values of optical thickness, KL, were also derived by fitting the spectral data and these values were compared to extinction based KL measurements. The spectrally derived KL was within a factor of about 1.5 from the extinction based data for the higher sooting cases. Under lower sooting conditions the differences were larger. For the lowest sooting case, the radiant fraction-defined as the fraction of energy emitted by radiation relative to the chemical energy available from the fuel injection-was negligible at less than 0.01%. The highest temperature flame with the greatest optical thickness resulted in a radiant fraction of 0.46%. Copyright © 2014 SAE International.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

This paper provides an analysis of high-pressure phenomena and its potential effects on the fundamental physics of fuel injection in Diesel engines. We focus on conditions when cylinder pressures exceed the thermodynamic critical pressure of the injected fuel and describe the major differences that occur in the jet dynamics compared to that described by classical spray theory. To facilitate the analysis, we present a detailed model framework based on the Large Eddy Simulation (LES) technique that is designed to account for key high-pressure phenomena. Using this framework, we perform a detailed analysis using the experimental data posted as part of the Engine Combustion Network (see www.sandia.gov/ECN): namely the "Baseline n-heptane" and "Spray-A (n-dodecane)" cases, which are designed to emulate conditions typically observed in Diesel engines. Calculations are performed by rigorously treating the experimental geometry, operating conditions and relevant thermo-physical gas-liquid mixture properties. Results are further processed using linear gradient theory, which facilitates calculations of detailed vapor-liquid interfacial structures, and compared with the high-speed imaging data. Analysis of the data reveals that fuel enters the chamber as a compressed liquid and is heated at supercritical pressure. Further analysis suggests that, at certain conditions studied here, the classical view of spray atomization as an appropriate model is questionable. Instead, nonideal real-fluid behavior must be taken into account using a multicomponent formulation that applies to arbitrary hydrocarbon mixtures at high-pressure supercritical conditions.

Abstract not provided.

Abstract not provided.

This report documents the results of a project funded by DoD's Strategic Environmental Research and Development Program (SERDP) on the science behind development of predictive models for soot emission from gas turbine engines. Measurements of soot formation were performed in laminar flat premixed flames and turbulent non-premixed jet flames at 1 atm pressure and in turbulent liquid spray flames under representative conditions for takeoff in a gas turbine engine. The laminar flames and open jet flames used both ethylene and a prevaporized JP-8 surrogate fuel composed of n-dodecane and m-xylene. The pressurized turbulent jet flame measurements used the JP-8 surrogate fuel and compared its combustion and sooting characteristics to a world-average JP-8 fuel sample. The pressurized jet flame measurements demonstrated that the surrogate was representative of JP-8, with a somewhat higher tendency to soot formation. The premixed flame measurements revealed that flame temperature has a strong impact on the rate of soot nucleation and particle coagulation, but little sensitivity in the overall trends was found with different fuels. An extensive array of non-intrusive optical and laser-based measurements was performed in turbulent non-premixed jet flames established on specially designed piloted burners. Soot concentration data was collected throughout the flames, together with instantaneous images showing the relationship between soot and the OH radical and soot and PAH. A detailed chemical kinetic mechanism for ethylene combustion, including fuel-rich chemistry and benzene formation steps, was compiled, validated, and reduced. The reduced ethylene mechanism was incorporated into a high-fidelity LES code, together with a moment-based soot model and models for thermal radiation, to evaluate the ability of the chemistry and soot models to predict soot formation in the jet diffusion flame. The LES results highlight the importance of including an optically-thick radiation model to accurately predict gas temperatures and thus soot formation rates. When including such a radiation model, the LES model predicts mean soot concentrations within 30% in the ethylene jet flame.

This paper presents experimental results for two fuel-related topics in a diesel engine: (1) how fuel volatility affects the premixed burn and heat release rate, and (2) how ignition quality influences the soot formation. Fast evaporation of fuel may lead to more intense heat release if a higher percentage of the fuel is mixed with air to form a combustible mixture. However, if the evaporation of fuel is driven by mixing with high-temperature gases from the ambient, a high-volatility fuel will require less oxygen entrainment and mixing for complete vaporization and, consequently, may not have potential for significant heat release simply because it has vaporized. Fuel cetane number changes also cause uncertainty regarding soot formation because variable ignition delay will change levels of fuel-air mixing prior to combustion. To address these questions, experiments are performed using a constant-volume combustion chamber simulating typical low-temperature-combustion (LTC) diesel conditions. We use fuels that have the same ignition delay (and therefore similar time for premixing with air), but different fuel volatility, to assess the heat-release rate and spatial location of combustion. Under this condition, where fuel volatility is decoupled from the ignition delay, results show almost the same heat release rate and spatial location of the premixed burn. The effect of ignition quality on soot formation has also been studied while maintaining similar levels of fuel-ambient mixing prior to combustion. To achieve the same ignition delay, the high-cetane-number fuel is injected into an ambient gas at a lower temperature and vice versa. The total soot mass within the spray is measured and compared for fuels with different cetane numbers but with the same premixing level (e.g. the same ignition delay and lift-off length). Experimental results show that the combination of high cetane number and low ambient gas temperature produces lower soot than the other combination, because the ambient temperature predominantly affects soot formation.

Abstract not provided.

Shadowgraph/schlieren imaging techniques have often been used for flow visualization of reacting and non-reacting systems. In this paper we show that high-speed shadowgraph visualization in a high-pressure chamber can also be used to identify cool-flame and high-temperature combustion regions of diesel sprays, thereby providing insight into the time sequence of diesel ignition and combustion. When coupled to simultaneous high-speed Mie-scatter imaging, chemiluminescence imaging, pressure measurement, and spatially-integrated jet luminosity measurements by photodiode, the shadowgraph visualization provides further information about spray penetration after vaporization, spatial location of ignition and high-temperature combustion, and inactive combustion regions where problematic unburned hydrocarbons exist. Examples of the joint application of high-speed diagnostics include transient non-reacting and reacting injections, as well as multiple injections. Shadowgraph and schlieren image processing steps required to account for variations of refractive index within the high-temperature combustion vessel gases are also shown.

Diesel injection parameters effect on liquid-phase diesel spray penetration after the end-of-injection (EOI) is investigated in a constant-volume chamber over a range of ambient and injector conditions typical of a diesel engine. Our past work showed that the maximum liquid penetration length of a diesel spray may recede towards the injector after EOI at some conditions. Analysis employing a transient jet entrainment model showed that increased fuel-ambient mixing occurs during the fuel-injection-rate ramp-down as increased ambient-entrainment rates progress downstream (i.e. the entrainment wave), permitting complete fuel vaporization at distances closer to the injector than the quasi-steady liquid length. To clarify the liquid-length recession process, in this study we report Mie-scatter imaging results near EOI over a range of injection pressure, nozzle size, fuel type, and rate-of-injection shape. We then use a transient jet entrainment model for detailed analysis. Results show that an increased injection pressure correlates well with increasing liquid length recession due to an increased entrainment wave speed. Likewise, an increased nozzle size, with higher jet momentum and faster entrainment wave, enhances the liquid length recession. A low-density, high-volatility fuel does not decrease the strength of the entrainment wave; however, it decreases the steady liquid length causing the entrainment wave to reach the liquid spray tip earlier, which ultimately results in faster liquid length recession. A slow ramp down in injection rate causes a weaker entrainment wave so that the liquid length recession occurs even prior to injector close.