While recent research has greatly improved our ability to test and model nonlinear dynamic systems, it is rare that these studies quantify the effect that the nonlinearity would have on failure of the structure of interest. While several very notable exceptions certainly exist, such as the work of Hollkamp et al. on the failure of geometrically nonlinear skin panels for high speed vehicles (see, e.g., Gordon and Hollkamp, Reduced-order models for acoustic response prediction. Technical Report AFRL-RB-WP-TR-2011-3040, Air Force Research Laboratory, AFRL-RB-WP-TR-2011-3040, Dayton, 2011. Issue: AFRL-RB-WP-TR-2011-3040AFRL-RB-WP-TR-2011-3040), other studies have given little consideration to failure. This work studies the effect of common nonlinearities on the failure (and failure margins) of components that undergo durability testing in dynamic environments. This context differs from many engineering applications because one usually assumes that any nonlinearities have been fully exercised during the test.
Bifurcations are commonly encountered during force controlled swept and stepped sine testing of nonlinear structures, which generally leads to the so-called jump-down or jump-up phenomena between stable solutions. There are various experimental closed-loop control algorithms, such as control-based continuation and phase-locked loop, to stabilize dynamical systems through these bifurcations, but they generally rely on specialized control algorithms that are not readily available with many commercial data acquisition software packages. A recent method was developed to experimentally apply sequential continuation using the shaker voltage that can be readily deployed using commercially available software. By utilizing the stabilizing effects of electrodynamic shakers and the force dropout phenomena in fixed frequency voltage control sine tests, this approach has been demonstrated to stabilize the unstable branch of a nonlinear system with three branches, allowing for three multivalued solutions to be identified within a specific frequency bandwidth near resonance. Recent testing on a strongly nonlinear system with vibro-impact nonlinearity has revealed jumping behavior when performing sequential continuation along the voltage parameter, like the jump phenomena seen during more traditional force controlled swept and stepped sine testing. This paper investigates the stabilizing effects of an electrodynamic shaker on strongly nonlinear structures in fixed frequency voltage control tests using both numerical and experimental methods. The harmonic balance method is applied to the coupled shaker-structure system with an electromechanical model to simulate the fixed voltage control tests and predict the stabilization for different parameters of the model. The simulated results are leveraged to inform the design of a set of experiments to demonstrate the stabilization characteristics on a fixture-pylon assembly with a vibro-impact nonlinearity. Through numerical simulation and experimental testing on two different strongly nonlinear systems, the various parameters that influence the stability of the coupled shaker-structure are revealed to better understand the performance of fixed frequency voltage control tests.
Bifurcations are commonly encountered during force controlled swept and stepped sine testing of nonlinear structures, which generally leads to the so-called jump-down or jump-up phenomena between stable solutions. There are various experimental closed-loop control algorithms, such as control-based continuation and phase-locked loop, to stabilize dynamical systems through these bifurcations, but they generally rely on specialized control algorithms that are not readily available with many commercial data acquisition software packages. A recent method was developed to experimentally apply sequential continuation using the shaker voltage that can be readily deployed using commercially available software. By utilizing the stabilizing effects of electrodynamic shakers and the force dropout phenomena in fixed frequency voltage control sine tests, this approach has been demonstrated to stabilize the unstable branch of a nonlinear system with three branches, allowing for three multivalued solutions to be identified within a specific frequency bandwidth near resonance. Recent testing on a strongly nonlinear system with vibro-impact nonlinearity has revealed jumping behavior when performing sequential continuation along the voltage parameter, like the jump phenomena seen during more traditional force controlled swept and stepped sine testing. Here, this paper investigates the stabilizing effects of an electrodynamic shaker on strongly nonlinear structures in fixed frequency voltage control tests using both numerical and experimental methods. The harmonic balance method is applied to the coupled shaker-structure system with an electromechanical model to simulate the fixed voltage control tests and predict the stabilization for different parameters of the model. The simulated results are leveraged to inform the design of a set of experiments to demonstrate the stabilization characteristics on a fixture-pylon assembly with a vibro-impact nonlinearity. Through numerical simulation and experimental testing on two different strongly nonlinear systems, the various parameters that influence the stability of the coupled shaker-structure are revealed to better understand the performance of fixed frequency voltage control tests.
When exposed to mechanical environments such as shock and vibration, electrical connections may experience increased levels of contact resistance associated with the physical characteristics of the electrical interface. A phenomenon known as electrical chatter occurs when these vibrations are large enough to interrupt the electric signals. It is critical to understand the root causes behind these events because electrical chatter may result in unexpected performance or failure of the system. The root causes span a variety of fields, such as structural dynamics, contact mechanics, and tribology. Therefore, a wide range of analyses are required to fully explore the physical phenomenon. This paper intends to provide a better understanding of the relationship between structural dynamics and electrical chatter events. Specifically, electrical contact assembly composed of a cylindrical pin and bifurcated structure were studied using high fidelity simulations. Structural dynamic simulations will be performed with both linear and nonlinear reduced-order models (ROM) to replicate the relevant structural dynamics. Subsequent multi-physics simulations will be discussed to relate the contact mechanics associated with the dynamic interactions between the pin and receptacle to the chatter. Each simulation method was parametrized by data from a variety of dynamic experiments. Both structural dynamics and electrical continuity were observed in both the simulation and experimental approaches, so that the relationship between the two can be established.
One of the more crucial aspects of any mechanical design is the joining methodology of parts. During structural dynamic environments, the ability to analyze the joint and fasteners in a system for structural integrity is fundamental, especially early in a system design during design trade studies. Different modeling representations of fasteners include spring, beam, and solid elements. In this work, we compare the various methods for a linear system to help the analyst decide which method is appropriate for a design study. Ultimately, if stresses of the parts being connected are of interest, then we recommend the use of the Ring Method for modeling the joint. If the structural integrity of the fastener is of interest, then we recommend the Spring Method.
Calibrating a finite element model to test data is often required to accurately characterize a joint, predict its dynamic behavior, and determine fastener fatigue life. In this work, modal testing, model calibration, and fatigue analysis are performed for a bolted structure, and various joint modeling techniques are compared. The structure is designed to test a single bolt to fatigue failure by utilizing an electrodynamic modal shaker to axially force the bolted joint at resonance. Modal testing is done to obtain the dynamic properties, evaluate finite element joint modeling techniques, and assess the effectiveness of a vibration approach to fatigue testing of bolts. Results show that common joint models can be inaccurate in predicting bolt loads, and even when updated using modal test data, linear structural models alone may be insufficient in evaluating fastener fatigue.
A proper understanding of the complex physics associated with nonlinear dynamics can improve the accuracy of predictive engineering models and provide a foundation for understanding nonlinear response during environmental testing. Several researchers and studies have previously shown how localized nonlinearities can influence the global vibration modes of a system. This current work builds upon the study of a demonstration aluminum aircraft with a mock pylon with an intentionally designed, localized nonlinearity. In an effort to simplify the identification of the localized nonlinearity, previous work has developed a simplified experimental setup to collect experimental data for the isolated pylon mounted to a stiff fixture. This study builds on these test results by correlating a multi-degree-of-freedom model of the pylon to identify the appropriate model form and parameters of the nonlinear element. The experimentally measured backbone curves are correlated with a nonlinear Hurty/Craig-Bampton (HCB) reduced order model (ROM) using the calculated nonlinear normal modes (NNMs). Following the calibration, the nonlinear HCB ROM of the pylon is attached to a linear HCB ROM of the wing to predict the NNMs of the next-level wing-pylon assembly as a pre-test analysis to better understand the significance of the localized nonlinearity on the global modes of the wing structure.
Calibrating a finite element model to test data is often required to accurately characterize a joint, predict its dynamic behavior, and determine fastener fatigue life. In this work, modal testing, model calibration, and fatigue analysis are performed for a bolted structure, and various joint modeling techniques are compared. The structure is designed to test a single bolt to fatigue failure by utilizing an electrodynamic modal shaker to axially force the bolted joint at resonance. Modal testing is done to obtain the dynamic properties, evaluate finite element joint modeling techniques, and assess the effectiveness of a vibration approach to fatigue testing of bolts. Results show that common joint models can be inaccurate in predicting bolt loads, and even when updated using modal test data, linear structural models alone may be insufficient in evaluating fastener fatigue.
Nonlinear force appropriation is an extension of its linear counterpart where sinusoidal excitation is applied to a structure with a modal shaker and phase quadrature is achieved between the excitation and response. While a standard practice in modal testing, modal shaker excitation has the potential to alter the dynamics of the structure under test. Previous studies have been conducted to address several concerns, but this work specifically focuses on a shaker-structure interaction phenomenon which arises during the force appropriation testing of a nonlinear structure. Under pure-tone sinusoidal forcing, a nonlinear structure may respond not only at the fundamental harmonic but also potentially at sub- or superharmonics, or it can even produce aperiodic and chaotic motion in certain cases. Shaker-structure interaction occurs when the response physically pushes back against the shaker attachment, producing non-fundamental harmonic content in the force measured by the load cell, even for pure tone voltage input to the shaker. This work develops a model to replicate these physics and investigates their influence on the response of a nonlinear normal mode of the structure. Experimental evidence is first provided that demonstrates the generation of harmonic content in the measured load cell force during a force appropriation test. This interaction is replicated by developing an electromechanical model of a modal shaker attached to a nonlinear, three-mass dynamical system. Several simulated experiments are conducted both with and without the shaker model in order to identify which effects are specifically due to the presence of the shaker. The results of these simulations are then compared to the undamped nonlinear normal modes of the structure under test to evaluate the influence of shaker-structure interaction on the identified system's dynamics.