In order to achieve higher rendering performance, the use of parallel sort-last architecture on a PC cluster is presented. The sort-last library (libpglc) can be linked to an existing parallel application to achieve high rendering rates. The efficient use of 64 commodity graphics cards enables to establish pace-setting rendering performance of 300 million triangles per second on extremely large data.
This report is a summary of the work completed in FY00 for science-based characterization of the processes used to fabricate cermet vias in source feedthrus. In particular, studies were completed to characterize the CND50 cermet slurry, characterize solvent imbibition, and identify critical via filling variables. These three areas of interest are important to several processes pertaining to the production of neutron generator tubes. Rheological characterization of CND50 slurry prepared with 94ND2 and Sandi94 primary powders were also compared. The 94ND2 powder was formerly produced at the GE Pinellas Plant and the Sandi94 is the new replacement powder produced at CeramTec. Processing variables that may effect the via-filling process were also studied and include: the effect of solids loading in the CND50 slurry; the effect of milling time; and the effect of Nuosperse (a slurry ''conditioner''). Imbibition characterization included a combination of experimental, theoretical, and computational strategies to determine solvent migration though complex shapes, specifically vias in the source feedthru component. Critical factors were determined using a controlled set of experiments designed to identify those variables that influence the occurrence of defects within the cermet filled via. These efforts were pursued to increase part production reliability, understand selected fundamental issues that impact the production of slurry-filled parts, and validate the ability of the computational fluid dynamics code, GOMA, to simulate these processes. Suggestions are made for improving the slurry filling of source feedthru vias.
As part of the full scale fuel fire experimental program, a series of JP-8 pool fire experiments with a large cylindrical calorimeter (3.66 m diameter), representing a C-141 aircraft fuselage, at the lee end of the fuel pool were performed at Naval Air Warfare Center, Weapons Division (NAWCWPNS). The series was designed to support Weapon System Safety Assessment (WSSA) needs by addressing the case of a transport aircraft subjected to a large fuel fire. The data collected from this mock series will allow for characterization of the fire environment via a survivable test fixture. This characterization will provide important background information for a future test series utilizing the same fuel pool with an actual C-141 aircraft in place of the cylindrical calorimeter.
This report provides an independent assessment of information on mixed waste streams, chemical compatibility information on polymers, and standard test methods for polymer properties. It includes a technology review of mixed low-level waste (LLW) streams and material compatibilities, validation for the plan to test the compatibility of simulated mixed wastes with potential seal and liner materials, and the test plan itself. Potential packaging materials were reviewed and evaluated for compatibility with expected hazardous wastes. The chemical and physical property measurements required for testing container materials were determined. Test methodologies for evaluating compatibility were collected and reviewed for applicability. A test plan to meet US Department of Energy and Environmental Protection Agency requirements was developed. The expected wastes were compared with the chemical resistances of polymers, the top-ranking polymers were selected for testing, and the most applicable test methods for candidate seal and liner materials were determined. Five recommended solutions to simulate mixed LLW streams are described. The test plan includes descriptions of test materials, test procedures, data collection protocols, safety and environmental considerations, and quality assurance procedures. The recommended order of testing to be conducted is specified.
In this study, the erosion properties of four sediments related to the Canaveral Ocean Dredged Material Disposal Site have been determined as a function of density, consolidation, and shear stress by means of a high shear stress sediment erosion flume at Sandia National Laboratories. Additional analysis was completed for each sediment to determine mineralogy, particle size, and organic content. This was done to support numerical modeling efforts, aid in effective management, and minimize environmental impact. The motivation for this work is based on concerns of dredged material transporting beyond the designated site and estimates of site capacity.
This paper provides an overview John Holland's Echo model, describes an implementation of the model, documents results from preliminary experiments using the model, and proposes further research in using Echo to study complex adaptive systems. Echo simulates the behavior of complex adaptive systems and can provide an experimental testbed for exploring theories of, and developing tools useful for analyzing these systems. Preliminary results indicate that the dynamic behavior of Echo can be used to generate interesting, time-series data that will be useful for evaluating the applicability of and developing tools, techniques, and possibly general theories, for the analysis of specific complex adaptive systems.
This report contains the design basis for a generic molten-salt solar power tower. A solar power tower uses a field of tracking mirrors (heliostats) that redirect sunlight on to a centrally located receiver mounted on top a tower, which absorbs the concentrated sunlight. Molten nitrate salt, pumped from a tank at ground level, absorbs the sunlight, heating it up to 565 C. The heated salt flows back to ground level into another tank where it is stored, then pumped through a steam generator to produce steam and make electricity. This report establishes a set of criteria upon which the next generation of solar power towers will be designed. The report contains detailed criteria for each of the major systems: Collector System, Receiver System, Thermal Storage System, Steam Generator System, Master Control System, and Electric Heat Tracing System. The Electric Power Generation System and Balance of Plant discussions are limited to interface requirements. This design basis builds on the extensive experience gained from the Solar Two project and includes potential design innovations that will improve reliability and lower technical risk. This design basis document is a living document and contains several areas that require trade-studies and design analysis to fully complete the design basis. Project- and site-specific conditions and requirements will also resolve open To Be Determined issues.
This report documents an investigation of irreversible electrical breakdown in ZnO varistors due to short pulses of high electric field and current density. For those varistors that suffer breakdown, there is a monotonic, pulse-by-pulse degradation in the switching electric field. The electrical and structural characteristics of varistors during and after breakdown are described qualitatively and quantitatively. Once breakdown is nucleated, the degradation typically follows a well-defined relationship between the number of post-initiation pulses and the degraded switching voltage. In some cases the degraded varistor has a remnant 20 {micro}m diameter hollow track showing strong evidence of once-molten ZnO. A model is developed for both electrical and thermal effects during high energy pulsing. The breakdown is assumed to start at one electrode and advance towards the other electrode as a thin filament of conductive material that grows incrementally with each successive pulse. The model is partially validated by experiments in which the varistor rod is cut at several different lengths from the electrode. Invariably one section of the cut varistor has a switching field that is not degraded while the other section(s) are heavily degraded. Based on the experiments and models of behavior during breakdown, some speculations about the nature of the nucleating mechanism are offered in the last section.
This report describes the 19-foot diameter blast tunnel at Sandia National Laboratories. The blast tunnel configuration consists of a 6 foot diameter by 200 foot long shock tube, a 6 foot diameter to 19 foot diameter conical expansion section that is 40 feet long, and a 19 foot diameter test section that is 65 feet long. Therefore, the total blast tunnel length is 305 feet. The development of this 19-foot diameter blast tunnel is presented. The small scale research test results using 4 inch by 8 inch diameter and 2 foot by 6 foot diameter shock tube facilities are included. Analytically predicted parameters are compared to experimentally measured blast tunnel parameters in this report. The blast tunnel parameters include distance, time, static, overpressure, stagnation pressure, dynamic pressure, reflected pressure, shock Mach number, flow Mach number, shock velocity, flow velocity, impulse, flow duration, etc. Shadowgraphs of the shock wave are included for the three different size blast tunnels.
Strain-induced self-assembly during semiconductor heteroepitaxy offers a promising approach to produce quantum nanostructures for nanologic and optoelectronics applications. Our current research direction aims to move beyond self-assembly of the basic quantum dot towards the fabrication of more complex, potentially functional structures such as quantum dot molecules and quantum wires. This report summarizes the steps taken to improve the growth quality of our GeSi molecular beam epitaxy process, and then highlights the outcomes of this effort.
Methods to determine unsaturated hydraulic properties can exhibit random and nonunique behavior. We assess the causes for these behaviors by visualizing microscale phase displacement processes that occur during equilibrium retention and transient outflow experiments. For both types of experiments we observe the drainage process to be composed of a mixture of fast air fingering and slower air back-filling. The influence of each of these microscale processes is controlled by a combination of the size and the speed of the applied boundary step, the initial saturation and its structure, and small-scale heterogeneities. Because the mixture of these microscale processes yields macroscale effective behavior, measured unsaturated flow properties are also a function of these controls. Such results suggest limitations on the current definitions and uniqueness of unsaturated hydraulic properties.
As a participating national lab in the inter-institutional effort to resolve performance issues of the non-elutable ion exchange technology for Cs extraction, they have carried out a series of characterization studies of UOP IONSIV{reg_sign} IE-911 and its component parts. IE-911 is a bound form (zirconium hydroxide-binder) of crystalline silicotitanate (CST) ion exchanger. The crystalline silicotitanate removes Cs from solutions by selective ion exchange. The performance issues of primary concern are: (1) excessive Nb leaching and subsequent precipitation of column-plugging Nb-oxide material, and (2) precipitation of aluminosilicate on IE-911 pellet surfaces, which may be initiated by dissolution of Si from the IE-911, thus creating a supersaturated solution with respect to silica. In this work, they have identified and characterized Si- and Nb-oxide based impurity phases in IE-911, which are the most likely sources of leachable Si and Nb, respectively. Furthermore, they have determined the criteria and mechanism for removal from IE-911 of the Nb-based impurity phase that is responsible for the Nb-oxide column plugging incidents.
This report summarizes progress from the Laboratory Directed Research and Development (LDRD) program during fiscal year 2000. In addition to a programmatic and financial overview, the report includes progress reports from 244 individual R and D projects in 13 categories.