Publications

The electronics industry has relied heavily upon the use of soldering for both package construction and circuit assembly. The solder attachment of devices onto printed circuit boards and ceramic microcircuits has supported the high volume manufacturing processes responsible for low cost, high quality consumer products and military hardware. Defects incurred during the manufacturing process are minimized by the proper selection of solder alloys, substrate materials and process parameters. Prototyping efforts are then used to evaluate the manufacturability of the chosen material systems. Once manufacturing feasibility has been established, service reliability of the final product is evaluated through accelerated testing procedures.

To deliver high bandwidth, a ubiquitous inter-/intra-building cable plant consisting of single mode and multimode fiber as well as twisted pair copper is required. The selection of the ``glue`` to transport and interconnect distributed LANs with central facility resources over a pervasive cable plant is the focus of this paper. A description of the traditional problems that must be overcome to provide very high bandwidth beyond the narrow confines of a computer center is given. The applicability of Asynchronous Transfer Mode (ATM) switching (interconnection) and Synchronous Optical NETwork (SONET) (transport) for high bandwidth delivery is described using the environment and requirements of Sandia National Laboratories. Other methods for distributing high data rates are compared and contrasted. Sandia is implementing a standards based foundation utilizing a pervasive single mode fiber cable plant, SONET transport, and ATM switching to meet the goals of gigabit networking.

The intent of this report is to examine the performance of the Deployable Seismic Verification System (DSVS) developed by the Department of Energy (DOE) through its national laboratories to support monitoring of underground nuclear test treaties. A DSVS was installed at the Pinedale Seismic Research Facility (PSRF) near Boulder, Wyoming during 1991 and 1992. This includes a description of the system and the deployment site. System performance was studied by looking at four areas: system noise, seismic response, state of health (SOH) and operational capabilities.

The three papers in this report were presented at the second international workshop to feature the Waste Isolation Pilot Plant (WIPP) Materials Interface Interactions Test (MIIT). This Workshop on In Situ Tests on Radioactive Waste Forms and Engineered Barriers was held in Corsendonk, Belgium, on October 13--16, 1992, and was sponsored by the Commission of the European Communities (CEC). The Studiecentrum voor Kernenergie/Centre D`Energie Nucleaire (SCK/CEN, Belgium), and the US Department of Energy (via Savannah River) also cosponsored this workshop. Workshop participants from Belgium, France, Germany, Sweden, and the United States gathered to discuss the status, results and overviews of the MIIT program. Nine of the twenty-five total workshop papers were presented on the status and results from the WIPP MIIT program after the five-year in situ conclusion of the program. The total number of published MIIT papers is now up to almost forty. Posttest laboratory analyses are still in progress at multiple participating laboratories. The first MIIT paper in this document, by Wicks and Molecke, provides an overview of the entire test program and focuses on the waste form samples. The second paper, by Molecke and Wicks, concentrates on technical details and repository relevant observations on the in situ conduct, sampling, and termination operations of the MIIT. The third paper, by Sorensen and Molecke, presents and summarizes the available laboratory, posttest corrosion data and results for all of the candidate waste container or overpack metal specimens included in the MIIT program.

This paper is an introductory discussion of stress pulse phenomena in simple solids and fluids. Stress pulse phenomena is a very rich and complex field that has been studied by many scientists and engineers. This paper describes the behavior of stress pulses in idealized materials. Inviscid fluids and simple solids are realistic enough to illustrate the basic behavior of stress pulses. Sections 2 through 8 deal with the behavior of pressure pulses. Pressure is best thought of as the average stress at a point. Section 9 deals with shear stresses which are most important in studying solids.

Sandia National Laboratories, New Mexico, conducts the Utility Battery Storage Systems Program, which is sponsored by the US Department of Energy`s Office of Energy Management. As a part of this program, four utility-specific systems studies were conducted to identify potential battery energy storage applications within each utility network and estimate the related benefits. This report contains the results of these systems studies.

Solid state silicon-29 nuclear magnetic resonance (NMR) spectroscopy has been used to characterize the formation of high pressure silica polymorphs and amorphous material associated with the shocked Coconino Sandstone from Meteor Crater, Arizona. Five samples of the sandstone were obtained from several locations at the crater to represent a range of shock conditions associated with the hypervelocity impact of a 30 m-diameter meteorite. The NMR spectra for these powdered materials exhibit peaks assigned to quartz, coesite, stishovite, and glass. A new resonance in two of the moderately shocked samples is also observed. This resonance has been identified as a densified form of amorphous silica with silicon in tetrahedra with one hydroxyl group. Such a phase is evidence for a shock-induced reaction between quartz and steam under high pressure conditions.

Sandia has developed an advanced operational control system approach, called Graphical Programming, to design and operate robot systems in unstructured environments. This Graphical Programming approach produces robot systems that are faster to develop and use, safer in operation, and cheaper overall than altemative teleoperation or autonomous robot control systems. This approach uses 3-D visualization and simulation software with intuitive operator interfaces for the programming and control of complex robotic systems. Supervisor software modules allow an operator to command and simulate complex tasks in a graphic preview mode and, when acceptable, command the actual robots and monitor their motions with the graphic system. Graphical Programming Supervisors maintain registration with the real world and allow the robot to perform tasks that cannot be accurately represented with models alone by using a combination of model and sensor-based control. All of these capabilities when combined result in a flexible system which is readily able to meet the demands called for in construction automation. This paper describes the Graphical Programming approach, several example control systems that use Graphical Programming, key features necessary for implementing successful Graphical Programming systems, and specific examples of applying these systems to robotic operations.

High spatial resoslution x-ray microanalysis in the analytical electron microscope (AEM) can be used to determine chemical composition on spatial scales of < 50 nm. Simple scattering models have the drawback of being incapable of treating electron scattering in inhomogeneous specimens, such as at phase interfaces or grain boundary segregation. The best method for calculating electron scattering and x-ray generation function is by Mone Carlo methods. Two examples are discussed: a phase interface in an Fe-Ni-Cr alloy, and grain boundary segregation using a 0.3 nm Cu slab in a 25 nm Al film (the slab is parallel to incident electron beam). It is concluded that high spatial resolution x-ray microanalysis can achieve near atomic resolution, but that massively parallel Monte Carlo models for electron scattering and a well characterized electron beam are needed.

Under a Cooperative Agreement between the Commission of European Communities (CEC) and the U. S. Department of Energy (DOE), the Joint Research Centre, (JRC) ISPRA, and Sandia National Laboratories (SNL) have been cooperating in the development of Containment and Surveillance equipment for a number of years. With recent technology advancements, this cooperation is expanding into the areas of Data Authentication, Safeguards Data Networks, Integrated Systems, and Image Processing. This paper will describe recently expanded efforts in connecting the Integrated Monitoring System designed by SNL to the Computer Aided Video Surveillance System designed by JRC. An SNL Modular Video Authentication System was furnished to test in the video circuitry of the Computer Aided Video Surveillance System. The two systems will remain at JRC for demonstrations, training, and future development activities.

Effective application of pan-tilt cameras in alarm assessment systems requires that the overall system design be such that any threat for which the system is designed will be within the field of view of the camera for a sufficiently long time for the assessment of the alarm to be performed. The assessment of alarms in large, unobstructed areas requires a different type of analysis than traditionally used for clear zones between fences along fixed perimeters where an intruder`s possible location is well defined. This paper presents a design methodology which integrates the threat characteristics, sensor detection pattern, system response time, and optics geometry considerations to identify all feasible locations for camera placement for effective assessment of large, unobstructed areas. The methodology also can be used to evaluate tradeoffs among these various considerations to improve candidate designs.

In this study we have developed the techniques to investigate the hydrodynamic response of high-strength ceramics by mixing these powders with copper powder, preparing compacts, and performing shock compression tests on these mixtures. Hydrodynamics properties of silicon carbide, titanium diboride, and boron carbide to 30 GPa were examined by this method, and hydrodynamic compression data for these ceramics have been determined. We have concluded, however, that the measurement method is sensitive to sample preparation and uncertainties in shock wave measurements. Application of the experimental technique is difficult and further efforts are needed.

Developments are reported in both experimental and numerical capabilities for characterizing the debris spray produced in penetration events. We have performed a series of high-velocity experiments specifically designed to examine the fragmentation of the projectile during impact. High-strength, well-characterized steel spheres (6.35 mm diameter) were launched with a two-stage light-gas gun to velocities in the range of 3 to 5 km/s. Normal impact with PMMA plates, thicknesses of 0.6 to 11 mm, applied impulsive loads of various amplitudes and durations to the steel sphere. Multiple flash radiography diagnostics and recovery techniques were used to assess size, velocity, trajectory and statistics of the impact-induced fragment debris. Damage modes to the primary target plate (plastic) and to a secondary target plate (aluminum) were also evaluated. Dynamic fragmentation theories, based on energy-balance principles, were used to evaluate local material deformation and fracture state information from CTH, a three-dimensional Eulerian solid dynamics shock wave propagation code. The local fragment characterization of the material defines a weighted fragment size distribution, and the sum of these distributions provides a composite particle size distribution for the steel sphere. The calculated axial and radial velocity changes agree well with experimental data, and the calculated fragment sizes are in qualitative agreement with the radiographic data. A secondary effort involved the experimental and computational analyses of normal and oblique copper ball impacts on steel target plates. High-resolution radiography and witness plate diagnostics provided impact motion and statistical fragment size data. CTH simulations were performed to test computational models and numerical methods.

Today`s integrated circuits are so complex that it is often necessary to have access to the layouts and schematics when performing voltage contrast, cross sectioning, light emission, mechanical probing, optical beam induced current, and even simple SEM and Optical Examination. To deal with these issues, Sandia National Laboratories is developing an advanced failure analysis laboratory networking scheme to provide computer control, layout navigation, schematic navigation, and report generation on each of the major pieces of failure analysis equipment. This concept is known as an Integrated Diagnostic Environment or IDE. An integrated diagnostic environment is an environment where failure analysis equipment is computer-controlled and linked by a high speed network. The network allows CAD databases to be shared between instruments, improving the failure analyst`s productivity on each analysis task. At Sandia, we are implementing this concept using SUN Sparcstation computers running Schlumberger`s IDE software. To date, we have incorporated our electron beam prober and light emission system into the environment. We will soon add our scanning optical microscope and focused ion beam system and eventually add our optical microscope and microprobe station into the network. There are a number of issues to consider when implementing an Integrated Diagnostic Environment; these are discussed in detail in this paper.

This paper describes the development and use of the Multi-Axis Seam racking (MAST) sensor for tracking seams or other features in real-time. Four independent, spatially-distributed electric fields are used to sense changes in the relative position of the sensor and the workpiece. The MAST sensor is very inexpensive compared with commercially available seam tracking sensors. It can be used in systems to perform cost-effective small-lot manufacturing operations in a faster, more consistent manner. The MAST sensor is used in an automated system for dispensing braze paste during a rocket nozzle fabrication process.

Short communication.

The ability for a communications network to realize arbitrary communications patterns can be expensive both in terms of hardware and in terms of system software. One might instead ask whether a system can be built which performs well for a given application program. In this paper we look at the question of when a set of communications patterns is suitable for fast realization on a given network. In particular we look at which patterns are realizable quickly on a mesh. Contrary to common wisdom, transpose is efficiently realizable on a mesh. However, some other important patterns such as shuffle are not.

The Milling Assistant (MA) programming system demonstrates the automated development of tool paths for Numerical Control (NC) machine tools. By integrating a Case-Based Reasoning decision processor with a commercial CAD/CAM software, intelligent tool path files for milled and point-to-point features can be created. The operational system is capable of reducing the time required to program a variety of parts and improving product quality by collecting and utilizing ``best of practice`` machining strategies.

The US Department of Energy (DOE) is sponsoring the Utility Battery Storage Systems Program at Sandia National Laboratories and its contractors. This program is specifically aimed at developing battery energy storage systems for electric utility applications commencing in the mid to late 1990s. One factory-integrated utility battery system and three battery technologies: sodium/sulfur, zinc/bromine, and lead-acid are being developed under this program. In the last few years the emphasis of this program has focused on battery system development. This emphasis has included greater interactions with utilities to define application requirements. Recent activities have identified specific applications of battery energy storage in certain utility systems and quantified the value of these applications to these utility companies. In part due to these activities, battery energy storage is no longer regarded by utilities as a load-leveling resource only, but as a multifunction, energy management resource.

The US Department of Energy is sponsoring the development of battery energy storage systems for electric utilities. An important part of this DOE program is the engineering of the battery subsystem. Because lower costs are possible and less space is required compared with conventional battery technologies, two advanced battery systems are being developed: sodium/sulfur and zinc/bromine. A brief description of the development approach being followed along with the current status of the sodium/sulfur technology is described in this paper. Of immediate relevance, a factory integrated modular sodium/sulfur system has been designed that incorporates many of the advantages of this technology. Each module (designated as NAS-P{sub AC}) combines a 600-kWh sodium/sulfur battery, a 300 kW power converter and a control system. In addition to the potential for low life-cycle cost, other specific benefits include excellent portability and an installed system-level footprint that is about 20% of an equivalent system using lead-acid batteries. The sodium/sulfur battery is designed to deliver its rated energy for 1500 cycles or 5 years of maintenance-free operation.

Sandia National Laboratories determined that the most effective method to address records management initiatives would be through a single, comprehensive facilities wide records inventory and retention schedule project. The logistic of such an undertaking (estimated at 425,000 linear feet) are demanding. The relatively short time frame required for completion and the project`s size called for sound, up front planning by Sandia and ultimately the support of an outside contractor for qualified resources to execute the plan.

Development of a high-temperature, superconducting, synchronous motor for large applications (>1000 HP) could offer significant electrical power savings for industrial users. Presently 60% of all electric power generated in the United States is converted by electric motors. A large part of two power is utilized by motors 1000 HP or larger. The use of high-temperature superconducting materials with critical temperatures above that of liquid nitrogen (77 K) in the field winding would reduce the losses in these motors significantly, and therefore, would have a definite impact on the electrical power usage in the US. These motors will be 1/3 to 1/2 the size of conventional motors of similar power and, thus, offer potential savings in materials and floor space. The cooling of the superconducting materials in the field windings of the rotor presents a unique application of cryogenic engineering. The rotational velocity results in significant radial pressure gradients that affect the flow distribution of the cryogen. The internal pressure fields can result in significant nonuniformities in the two-phase flow of the coolant. Due to the variable speed design, the flow distribution has the potential to change during operation. A multiphase-flow computer model of the cryogenic cooling is developed to calculate the boiling heat transfer and phase distribution of the nitrogen coolant in the motor. The model accounts for unequal phase velocities and nonuniform cooling requirements of the rotor. The unequal radial pressure gradients in the inlet and outlet headers result in a larger driving force for flow in the outer cooling channels. The effect of this must be accounted for in the design of the motor. Continuing improvements of the model will allow the investigation of the transient thermal issues associated with localized quenching of the superconducting components of the motor.

The deliverability of a reservoir depends primarily on its permeability, which, in many reservoirs, is controlled by a combination of natural fractures and the in situ stresses. Therefore it is important to be able to predict which parts of a basin are most likely to contain naturally fractured strata, what the characteristics of those fractures might be, and what the most likely in situ stresses are at a given location. This paper presents a set of geologic criteria that can be superimposed onto factors, such as levels of maturation and porosity development, in order to predict whether fractures are present once the likelihood of petroleum presence and reservoir development have been determined. Stress causes fracturing, but stresses are not permanent. A natural-fracture permeability pathway opened by one system of stresses may be held open by those stresses, or narrowed or even closed by changes of the stress to an oblique or normal orientation. The origin of stresses and stress anisotropies in a basin, the potential for stress to create natural fractures, and the causes of stress reorientation are examined in this paper. The appendices to this paper present specific techniques for exploiting and characterizing natural fractures, for measuring the present-day in situ stresses, and for reconstructing a computerized stress history for a basin.

By extracting and analyzing measurement (variables) data from portal metal detectors whenever possible instead of the more typical ``alarm``/``no-alarm`` (attributes or binomial) data, we can be more informed about metal detector health with fewer tests. This testing methodology discussed in this report is an alternative to the typical binomial testing and in many ways is far superior.

Varistor material is currently supplied by a single commercial source. The chem-prep varistor process was developed as a backup/replacement. With the transfer of the process to the production facility, studies were made to verify that the process is stable in manufacturing. Process variables are the precursors oxalic acid, NaOH, and ZnCl{sub 2}. Process stability was determined by comparing assay uncertainty region with precipitant/ZnCl{sub 2} compositional region meeting electrical and physical property specifications. Assay variability was assessed by conducting a round robin; standard deviations of repeated assays of the same sample was 0.1 wt% by the same labs; 0.1-0.4 wt% among laboratories. A mixture experiment was then conducted to assess the effects of the precipitants/ZnCl{sub 2} on breakdown field, nonlinearity coefficient, and bulk density. Results indicate that the chem-prep process can be stable; however the nominal target composition was on the edge of the composition region, and it was moved to the center of the large region with acceptable electrical and physical properties. Tests of unpotted component rods made from the new composition met all specifications. 8 refs, 10 figs, 10 tabs.

A summary is presented of the results of a number of studies conducted prior to March 1992 that have led to a conceptual model describing how the porosity (and therefore the permeability) of waste and backfill in a Waste Isolation Pilot Plant disposal room changes with time and also describes how results from calculations involving mathematical models of these processes are used to provide input into performance assessment of the repository. Included in the report are descriptions of essential material response or constitutive models that include the influence of gas generation and the response of simple gas-pressurized cracks and fractures in salt, marker beds, and clay seams. Two-dimensional versus three-dimensional disposal room configurations and descriptions of the differences between numerical codes are also discussed. Calculational results using the mathematical models for disposal room response are described, beginning with closure of empty rooms and becoming progressively more complex. More recent results address some of the effects of gas generation in a room containing waste and backfill and intersected by a gas permeable marker bed. Developments currently in progress to improve the evaluation of the disposal room performance are addressing the coupling between brine flow and closure and the two-dimensional capability for analyzing a complete panel of rooms. Next, a method is described for including disposal room closure results into performance assessment analyses that determine if the repository is in compliance with regulatory standards. The coupling is accomplished using closure surfaces that describe the relationship among porosity, total amount of gas in the repository, and time. A number of conclusions about room response and recommendations for further work are included throughout the report.

The transverse motion of a projectile in an electromagnetic induction launcher is considered. The equations of motion for translation and rotation are derived assuming a rigid projectile and a flyway restoring force per unit length that is proportional to the local displacement. Transverse forces and torques due to energized coils are derived for displaced or tilted projectile elements based on a first order perturbation method. The resulting equations of motion for a rigid projectile composed of multiple elements in a multi-coil launcher are analyzed as a coupled oscillator system of equations and a simple stability condition is derived. The equations of motion are incorporated into the 2-D Slingshot code and numerical solutions for the transverse motion are obtained. For the 20 meter navy launcher parameters we find that stability is achieved with a flyway spring constant of k {approx} 1{times} 10{sup 8} N/m{sup 2}. For k {approx} 1.5 {times} 10{sup 8} N/m{sup 2} and sample coil misalignment modeled as a sine wave of I mm amplitude at wavelengths of one or two meters, the projectile displacement grows to a maximum of 4 mm. This growth is due to resonance between the natural frequency of the Projectile transverse motion and the coil displacement wavelength. This resonance does not persist because of the changing axial velocity. Random coil displacement is also found to cause roughly the same projectile displacement. For the maximum displacement a rough estimate of the transverse pressure is 50 bars.

Uncertainty and sensitivity analysis techniques based on Latin hypercube sampling, partial correlation analysis, stepwise regression analysis and examination of scatterplots are used in conjunction with the BRAGFLO model to examine two phase flow (i.e., gas and brine) at the Waste Isolation Pilot Plant (WIPP), which is being developed by the US Department of Energy as a disposal facility for transuranic waste. The analyses consider either a single waste panel or the entire repository in conjunction with the following cases: (1) fully consolidated shaft, (2) system of shaft seals with panel seals, and (3) single shaft seal without panel seals. The purpose of this analysis is to develop insights on factors that are potentially important in showing compliance with applicable regulations of the US Environmental Protection Agency (i.e., 40 CFR 191, Subpart B; 40 CFR 268). The primary topics investigated are (1) gas production due to corrosion of steel, (2) gas production due to microbial degradation of cellulosics, (3) gas migration into anhydrite marker beds in the Salado Formation, (4) gas migration through a system of shaft seals to overlying strata, and (5) gas migration through a single shaft seal to overlying strata. Important variables identified in the analyses include initial brine saturation of the waste, stoichiometric terms for corrosion of steel and microbial degradation of cellulosics, gas barrier pressure in the anhydrite marker beds, shaft seal permeability, and panel seal permeability.

Satellite servicing is in many ways analogous to subsea robotic servicing in the late 1970`s. A cost effective, reliable, telerobotic capability had to be demonstrated before the oil companies invested money in deep water robot serviceable production facilities. In the same sense, aeronautic engineers will not design satellites for telerobotic servicing until such a quantifiable capability has been demonstrated. New space servicing systems will be markedly different than existing space robot systems. Past space manipulator systems, including the Space Shuttle`s robot arm, have used master/slave technologies with poor fidelity, slow operating speeds and most importantly, in-orbit human operators. In contrast, new systems will be capable of precision operations, conducted at higher rates of speed, and be commanded via ground-control communication links. Challenges presented by this environment include achieving a mandated level of robustness and dependability, radiation hardening, minimum weight and power consumption, and a system which accommodates the inherent communication delay between the ground station and the satellite. There is also a need for a user interface which is easy to use, ensures collision free motions, and is capable of adjusting to an unknown workcell (for repair operations the condition of the satellite may not be known in advance). This paper describes the novel technologies required to deliver such a capability.

A numerical method to simulate viscous diffusion of vorticity using vortex blobs (i.e., without a grid) is presented. The method consists of casting the effects of viscous diffusion into an effective ``diffusion velocity`` at which vortex blobs convect. The diffusion velocity was proposed previously by Ogami and Akamatsu, but they did not consider the effects of the divergence of the diffusion velocity. In fact, the diffusion velocity is highly non-solenoidal, which significantly affects the area over which a vortex blob diffuses. A formulation is presented that relates the area expansion to the diffusion velocity divergence. By taking into account the area expansion, more accurate simulations of diffusion are obtained, as demonstrated by a comparison of numerical and analytical diffusion solutions. Results from simulations show that vortex areas expand significantly in regions of large vorticity gradients. As a result of the area expansion, adjacent vortices remain overlapped, thereby maintaining smooth solution fields. The non-solenoidal diffusion velocity method is easily implemented in vortex blob algorithms, thus facilitating the development of vortex methods to simulate flows with finite Reynolds numbers.

Designed experiments were employed to characterize a process for etching phosphorus doped polycrystalline silicon with HBr in a close-coupled ECR plasma reactor configured for 200 mm wafers. A fractional factorial screening experiment was employed to determine the principal input factors and the main etch effects. Linear models of the process responses indicate RF power, O{sub 2} flow rate, and the position of the resonance zone (with respect to the wafer) as the three strongest factors influencing process performance. Response surfaces generated using data from a follow-on response surface methodology (RSM) experiment predicted an optimum operating region characterized by relatively low RF power, a small O{sub 2} flow, and a resonance zone position close to the wafer. The optimized process demonstrated a polysilicon etch rate of 270 nm/min, an etch rate non-uniformity of 2.2% (1s), an etch selectivity to oxide greater than 100:1, and anisotropic profiles. Particle test results for the optimized process indicated that careful selection of the O{sub 2} fraction is required to avoid polymer deposition and particle formation.

Before disposing of transuranic radioactive waste in the Waste Isolation Pilot Plant (WIPP), the United States Department of Energy (DOE) must evaluate compliance with applicable long-term regulations of the United States Environmental Protection Agency (EPA). Sandia National Laboratories is conducting iterative performance assessments (PAs) of the WIPP for the DOE to provide interim guidance while preparing for a final compliance evaluation. This volume of the 1992 PA contains results of uncertainty and sensitivity analyses with respect to migration of gas and brine from the undisturbed repository. Additional information about the 1992 PA is provided in other volumes. Volume 1 contains an overview of WIPP PA and results of a preliminary comparison with 40 CFR 191, Subpart B. Volume 2 describes the technical basis for the performance assessment, including descriptions of the linked computational models used in the Monte Carlo analyses. Volume 3 contains the reference data base and values for input parameters used in consequence and probability modeling. Volume 4 contains uncertainty and sensitivity analyses with respect to the EPA`s Environmental Standards for the Management and Disposal of Spent Nuclear Fuel, High-Level and Transuranic Radioactive Wastes (40 CFR 191, Subpart B). Finally, guidance derived from the entire 1992 PA is presented in Volume 6. Results of the 1992 uncertainty and sensitivity analyses indicate that, conditional on the modeling assumptions and the assigned parameter-value distributions, the most important parameters for which uncertainty has the potential to affect gas and brine migration from the undisturbed repository are: initial liquid saturation in the waste, anhydrite permeability, biodegradation-reaction stoichiometry, gas-generation rates for both corrosion and biodegradation under inundated conditions, and the permeability of the long-term shaft seal.

Experiment results are presented for unconfined compressive strength and elastic moduli of tuffaceous rocks from Busted Butte near Yucca Mountain, Nevada. The data have been compiled for the Yucca Mountain Site Characterization Project Site and Engineering Properties Data Base. Experiments were conducted on water-saturated specimens of the potential nuclear waste repository horizon Topopah Spring Member tuff (thermal/mechanical unit TSw2). The influence of strain rate on mechanical properties of the tuff was examined by loading six specimens in uniaxial compression at a strain rate of 10{sup {minus}9} s{sup {minus}1}. The experiments performed under ambient pressure and temperature conditions and conformed to Technical Procedure 91, titled ``Unconfined Compression Experiments at 22{degrees}C and a Strain Rate of 10{sup {minus}9} s{sup {minus}1}.`` The mean and standard deviation values of ultimate strength, Young`s modulus and Poisson`s ratio determined from these experiments are 85.4{plus_minus}21.7 MPa, 33.9{plus_minus}4.6 GPa, and 0.09{plus_minus}0.07, respectively.

Thermomechanical models are being developed to support the design of an Exploratory Studies Facility (ESF) and a potential high-level nuclear waste repository at Yucca Mountain, Nevada. These models are used for preclosure design of underground openings, such as access drifts, emplacement drifts, and waste emplacement boreholes; and in support of postclosure issue resolution relating to waste canister performance, disturbance of the hydrological properties of the host rock, and overall system performance assessment. For both design and performance assessment, the purpose of using models in analyses is to better understand and quantify some phenomenon or process. Therefore, validation is an important process that must be pursued in conjunction with the development and application of models. The Site Characterization Plan (SCP) addressed some general aspects of model validation, but no specific approach has, as yet, been developed for either design or performance assessment models. This paper will discuss a proposed process for thermomechanical model validation and will focus on the use of laboratory and in situ experiments as part of the validation process. The process may be generic enough in nature that it could be applied to the validation of other types of models, for example, models of unsaturated hydrologic flow.

Basaltic volcanism has been identified as a possible future event initiating a release of radionuclides from a potential repository at the proposed Yucca Mountain high-level waste repository site. The performance assessment method set forth in the Site Characterization Plan (DOE, 1988) requires that a set of scenarios encompassing all significant radionuclide release paths to the accessible environment be described. This report attempts to catalogue the details of the interactions between the features and processes produced by basaltic volcanism in the presence of the presumed groundwater flow system and a repository structure, the engineered barrier system (EBS), and waste. This catalogue is developed in the form of scenarios. We define a scenario as a well-posed problem, starting from an initiating event or process and proceeding through a logically connected and physically possible combination or sequence of features, events, and processes (FEPs) to the release of contaminants.

Sandia National Laboratories—a Department of Energy multiprogram national laboratory—has for over four decades applied its talents, tools, and techniques to solving technological problems of national scale. This publication provides information of interest about Sandia National Laboratories and the work being done there.

Commercial applications for advanced rechargeable batteries are constantly increasing. These applications include electric vehicles, large scale energy storage at electric utilities, storage of electrical energy produced by renewable energy resources such as solar or wind generators, and consumer electronics. Commercially available batteries are not able to meet the performance and/or cost requirements of many of these applications. To be successful, advanced battery technology need different combinations of high energy and power densities, long life, low cost, and little or no maintenance. In addition. completely safe operation must be assured.

There are many remote applications which require the dexterous manipulation of tools and materials in the field. These tasks range from the assembly and maintenance of space structures to the characterization and retrieval of hazardous materials here on Earth. Operations which involve the dexterous manipulation of hazardous materials in the field have, in the past, been completed by technicians. Use of humans in such hazardous operations is under increased scrutiny due to high costs and low productivity associated with providing protective clothing and environments. Traditional remote manual field operations have, unfortunately, proven to have very low productivity when compared with unencumbered human operators. Recent advances in the integration of sensors and computing into the control of remotely operated equipment have shown great promise for reducing the cost of remote systems while providing faster and safer remote systems. This paper discusses applications of such advances to remote field operations.

The Facilities Organization at Sandia has undergone many changes in the past five years. Management has made a commitment to improve the matrix management system and apply quality principles to the organization. This management commitment enabled Facilities to use project management tools for defining and documenting Facilities key processes. The resulting documentation included implementation plans for defining participant roles and responsibilities, identifying critical success factors, measuring performance, and ensuring continuous improvement. All of this resulted in benefits that demonstrate the value of project management and show how project management and quality are intertwined.

Centrifugally-cast concrete liners applied to the interiors of plain steel pipe sections were tested for corrosion performance in brine solutions. An American Petroleum Institute (API) standard concrete, with and without additions of a styrene-butadiene copolymer latex, was subjected to simulated service and laboratory tests. Simulated service tests used a mechanically pumped test manifold containing sections of concrete-lined pipe. Linear polarization probes embedded at steel-concrete interfaces tracked corrosion rates of these samples as a function of exposure time. Laboratory tests used electrochemical impedance spectroscopy to study corrosion occurring at the steel-concrete interfaces. Electron probe microanalysis (EPMA) determined ingress and distribution of damaging species, such as Cl, in concrete liners periodically returned from the field. Observations of concrete-liner fabrication indicate that latex loading levels were difficult to control in the centrifugal-casting process. Overall, test results indicate that latex additions do not impart significant improvements to the performance of centrifugally cast liners and may even be detrimental. Corrosion at steel-concrete interfaces appears to be localized and the area fraction of corroding interfaces can be greater in latex-modified concretes than in API baseline material. EPMA shows higher interfacial Cl concentration in the latex-modified concretes than in the API standard due to rapid brine transport through cracks to the steel surface.

A multimechanism constitutive model of creep has been developed which incorporates the workhardening and recovery transient creep behavior. This model has been applied to the creep of polycrystalline halite. The specific application of the model is in the calculation of the closure of underground rooms in layered salt deposits. Through the use of finite element calculations, this model, with appropriate laboratory material parameters and a Tresca flow potential, has predicted the measured closure of a number of large in situ experimental rooms.

Alkali metal heat-pipe receivers have been identified as a desirable interface to couple a Stirling-cycle engine with a parabolic dish solar concentrator. The reflux receiver provides power nearly isothermally to the engine heater heads while de-coupling the heater head design from the solar absorber surface design. The independent design of the receiver and engine heater head leads to high system efficiency. Heat pipe reflux receivers have been demonstrated at approximately 30 kW{sub t} power throughput by others. This size is suitable fm engine output powers up to 10 kW{sub e}. Several 25-kW{sub e}, Stirling-cycle engines exist, as well as designs for 75-kW{sub t} parabolic dish solar concentrators. The extension of heat pipe technology from 30 kW{sub t} to 75 kW{sub t} is not trivial. Heat pipe designs are pushed to their limits, and it is critical to understand the flux profiles expected from the dish, and the local performance of the wick structure. Sandia has developed instrumentation to monitor and control the operation of heat pipe reflux receivers to test their throughput limits, and analytical models to evaluate receiver designs. In the past 1.5 years, several heat pipe receivers have been tested on Sandia`s test bed concentrators (TBC`s) and 60-kW{sub t} solar furnace. A screen-wick heat pipe developed by Dynatherm was tested to 27.5 kW{sub t} throughput. A Cummins Power Generation (CPG)/Thermacore 30-kW{sub t} heat pipe was pushed to a throughput of 41 kW{sub t} to verify design models. A Sandia-design screen-wick and artery 75-kW{sub t} heat pipe and a CPG/Thermacore 75-kW{sub t} sintered-wick heat pipe were also limit tested on the TBC. This report reviews the design of these receivers, and compares test results with model predictions.

This paper compares the solderability performance and corrosions ion protection effectiveness of electroless tin coatings versus organic azole films after exposure to a series of humidity and thermal (lead-free solders) cycling conditions. The solderability of immersion tin is directly related to the tin oxide growth on the surface and is not affected by the formation of Sn-Cu intermetallic phases as long as the intermetallic phase is protected by a Sn layer. For a nominal tin thickness of 60{mu}inches, the typical thermal excursions associated with assembly are not sufficient to cause the intermetallic phase to consume the entire tin layer. Exposure to humidity at moderate to elevated temperatures promotes heavy tin oxide formation which leads to solderability loss. In contrast, thin azole films are more robust to humidity exposure; however upon heating in the presence of oxygen, they decompose and lead to severe solderability degradation. Evaluations of lead-free solder pastes for surface mount assembly applications indicate that immersion tin significantly improves the spreading of Sn:Ag and Sn:Bi alloys as compared to azole surface finishes.

A variety of industrial-standard and experimental concretes are being evaluated for use in brine disposal pipelines operated by the US Strategic Petroleum Reserve (SPR). This paper reports on interim performance results from on-going studies involving an American Petroleum Institute (API) standard calcium silicate-based (CS) concrete and a commercially available calcium aluminate-based (CA) concrete. Samples exposed to non-flowing SPR brine in the field were returned to the laboratory at regular intervals for analysis. Electron probe microanalysis (EPMA) determined the depth of brine penetration and the amount of concrete deterioration. Corrosion occurring at steel pipe/concrete interfaces during exposure to simulated brine has been studied on laboratory-constructed specimens using electrochemical impedance spectroscopy (EIS).

In December 1991, the Strategic Defense Initiative Organization (SDIO) decided to investigate the possibility of a US launch of a Russian Topaz II space nuclear power system. The primary mission goal would be to demonstrate and evaluate Nuclear Electric Propulsion technology to establish a capability for future civilian and military missions. A preliminary nuclear safety assessment, involving selected safety analyses, was initiated to determine whether or not a space mission could be conducted safely and within budget constraints. This paper describes the preliminary safety assessment results and the nuclear safety program now being established for the Nuclear Electric Propulsion Space Test Program (NEPSTP).

The PANDA code was used to develop an equation of state (EOS) for iron. Separate EOS tables were constructed for four solid phases and the fluid phase. The phase diagram and multiphase EOS table were then computed using the free energies. Results are in good agreement with thermophysical, static compression, phase boundary, and shock-wave measurements. Predicted pressures for the shock-induced {epsilon}-{gamma} and {gamma}-liquid transitions agree with those determined from sound speed measurements. Predicted melting temperatures fall in between two recent sets of experimental data which sharply disagree with one another.

Extensive work has been performed in the past which demonstrates that various metal alloys can be used to detect different toxic, hazardous, and flammable gases. Work has been performed using Pd, Pt, Ir, PdNi, PdAg and Pt/Pd for detecting things such as Hydrogen, Hydrazine, Hydrogen Sulfide, Deuterium, Tritium, Ethanol and Hexane. Perhaps the most familiar is the use of Pd and PdNi for the detection of Hydrogen. These devices work by examining the effect of the gases on the material properties of the metal alloys. Two of the most common material properties examined in these sensors are the resistance of thin film resistors, and the flatband or threshold voltage shifts of MOS structures fabricated with a particular alloy as the gate material. While research into these sensing techniques has shown much promise, few manufacturable, fieldable devices have resulted. These sensing techniques are prone to drift problems due to temperature variations, and typically have large sample to sample variations in performance due to process control issues. Typically, these sensors require significant external instrumentation for measurement and control, making the systems large and expensive. Sandia National Laboratories has designed, fabricated and demonstrated complete functionality of a generic microelectronic based smart sensor platform intended to effectively exploit the research mentioned above into high performance, manufacturable, fieldable devices. This smart sensor platform technology fabricates 2 {mu}m CMOS digital and analog control electronics, sensing elements, and temperature control elements on the same silicon integrated circuit. Our initial demonstration of this technology incorporates PdNi as the sensing alloy for the detection of hydrogen.

The RADionuclide Transport, Removal, And Dose (RADTRAD) code is designed for US Nuclear Regulatory Commission (USNRC) use to calculate the radiological consequences to the offsite population and to control room operators following a design-basis accident at Light Water Reactor (LWR) power plants. This code utilizes updated reactor accident source terms published in draft NUREG-1465, ``Accident Source Terms for Light-Water Nuclear Power Plants.`` The code will track the transport of radionuclides as they are released from the reactor pressure vessel, travel through the primary containment and other buildings, and are released to the environment. As the radioactive material is transported through the primary containment and other buildings, credit for several removal mechanisms may be taken including sprays, suppression pools, overlying pools, filters, and natural deposition. Simple models are available for these different removal mechanisms that use, as input, information about the conditions in the plant and predict either a removal coefficient ({lambda}) or decontamination factor. The user may elect to use these models or input a single value for a removal coefficient or decontamination factor.

A preconceptual design for an Accelerator Production of Tritium (APT) facility is currently under development by several national laboratories in conjunction with industry. The design consists of an accelerator that bombards a spallation target with high energy protons. Neutrons are produced in the spallation target and are absorbed in a blanket material to produce tritium. Two spallation targets are currently under investigation: (1) a tungsten neutron source target and (2) a lead neutron source target. In the tungsten target the neutrons are captured in helium-3, which is circulated through the system, thus producing tritium. The lead target is surrounded with a lithium-aluminum blanket and the tritium is produced in the lithium-6. The investigation of possible radiological impacts on the public is being performed as a part of the safety evaluations of the preconceptual design. These studies include the estimation of releases of radioactive materials from the two spallation targets and the possible impacts on the public.

A research and development program is being conducted by the University of Kentucky/Center for Applied Energy Research, Sandia National Laboratories, LDP Associates and CONSOL Inc. to improve current coal liquefaction technology by physical and chemical pretreatments of the coal and recycle oil. These pretreatment steps include: (1) agglomeration of the coal with ash-containing recycle oil to simultaneously reject coal ash and recycle-oil ash, (2) fluid coking of the distillation bottoms (ash-purge) stream and recycle of the coker overhead, (3) dewaxing of the distillate portion of the recycle oil, and (4) low-severity hydrotreatment of the coker overhead and dewaxed oil using hydrogen from an in-situ water-gas shift reaction. These pretreatment steps will remove the ash and unconverted coal, reducing the ash load in the system and simultaneously recovering the maximum amount of organics. Dewaxing and hydrotreatment will yield a high-quality recycle oil distillate. These pretreatment steps are being evaluated technically and economically to develop an improved conceptual liquefaction process. The baseline process to which the improved process will be compared is the Two-Stage Liquefaction Process as it was practiced at the Wilsonville, AL, USA Advanced Coal Liquefaction Test Facility.

This paper examines the role of the control objective and the control time in determining fuel-optimal actuator placement for structural vibration suppression. A general theory is developed that can be easily extended to include alternative performance metrics such as energy and time-optimal control. The performance metric defines a convex admissible control set which leads to a max-min optimization problem expressing optimal location as a function of initial conditions and control time. A solution procedure based on a nested Genetic Algorithm is presented and applied to an example problem. Results indicate that the optimal locations vary widely as a function of control time and initial conditions.

When restricted to cost arrays possessing the sum Monge property, many combinatorial optimization problems with sum objective functions become significantly easier to solve. Examples include the usual sum-objective-function versions of the assignment problem, the transportation problem, the traveling-salesman problem, and several shortest-path problems. Furthermore, the more general algebraic assignment and transportation problems, which are formulated in terms of an ordered commutative semigroup (H, *, {le}), are similarly easier to solve given cost arrays possessing the corresponding algebraic Monge property, which requires that for all i < k and j < {ell}, a[i,j] * a[k,{ell}] {le} a[i,{ell}] * a[k,j]. In this paper, we show that Monge-array results for two sum-of-edge-costs shortest-path problems can likewise be extended to a general algebraic setting, provided the problems` ordered commutative semigroup (H, *, {le}) satisfies one additional restriction. We also show how our algorithms can be modified to solve certain bottleneck shortest-path problems, even though the ordered commutative semigroup ({Re}, max, {le}) naturally associated with bottleneck problems does not satisfy our additional restriction. We also provide improved algorithms for several other bottleneck combinatorial optimization problems whose cost arrays possess the strict bottleneck Monge property. Finally, we show how our bottleneck shortest-path techniques can be used to obtain fast algorithms for a variant of Hirschberg and Larmore`s optimal paragraph formation problem, a processor-allocation problem first formulated by Bokhari, and a special case of the bottleneck traveling-salesman problem.

Robotics technology is being developed to assist in remediating high-level radioactive wastes stored in large tanks at the Department of Energy`s Hanford, Washington facility. Remediation activities will likely employ a remotely controlled long reach manipulator, capable of extending over 40 feet from its base, to deploy remediation end-effectors and sensors. Waste inside the tanks consists of hazardous vapor, liquid, sludge, solidified crystal, and various steel pipes and miscellaneous hardware. On November 10--12, 1992, a demonstration by Sandia National Laboratories of environmental sensor scanning and robot manipulated steel pipe cutting was performed on a tank mockup located at the Hanford facility. This paper describes the Sandia developed technology implemented at this demonstration.

The Analytic System and Software for Evaluation of Safeguards and Security (ASSESS) Facility module records site information in the path elements and areas of an Adversary Sequence Diagram. The ASSESS Outsider evaluation module takes this information and first calculates performance values describing how much detection and delay is assigned at each path element and then uses the performance values to determine most-vulnerable paths. This paper discusses new Outsider capabilities that allow the user to view how elements are being defeated and to modify some of these values in Outsider. Outsider now displays how different path element segments are defeated and contrasts the probability of detection for alternate methods of defeating a door (e.g., the lock or the door face itself). The user can also override element segment delays and detection probabilities directly during analysis in Outsider. These capabilities allow users to compare element performance and to verify correct path element performance for all elements, not just those on the most-vulnerable path as is the case currently. Improvements or reductions in protection can be easily checked without creating a set of new facility files to accomplish it.

Sandia National Laboratories (SNL) has shown that an automated personnel tracking and material monitoring system enhances protection of sensitive and classified parts against an insider. Such a system also significantly reduces the number of required, manual physical inventories at Department of Energy (DOE) sites while increasing assurance that material has not been diverted. SNL`s Insider Technology Department developed and is enhancing its generic, real-time, personnel tracking and material monitoring system. The system consists of facility selectable modules. This paper presents an overview of the modules, evaluation results, user`s suggestions, and future modules.

Although plasma cleaning is a recognized substitute for solvent cleaning in removing organic contaminants, some universal problems in plasma cleaning processes prevent wider use of plasma techniques. Lack of understanding of the fundamental mechanisms of the process, unreliable endpoint detection techniques, and slow process times make plasma cleaning processes less than desirable. Our approach to address these plasma cleaning problems is described. A comparison of plasma cleaning rates of oxygen and oxygen/sulfur hexafluoride gases shows that fluorine-containing plasmas can enhance etch rates by 400% over oxygen alone. A discussion of various endpoint indication techniques is discussed and compared for application suitability. Work toward a plasma cleaning database is discussed. In addition to the global problems of plasma cleaning, an experiment where the specific mixed-waste problem of removal of machine oils from radioactive scrap metal is discussed.

The US Department of Energy has required radiological sabotage vulnerability assessments to be conducted for years. However, the exact methodology to be used in this type of analysis still remains somewhat elusive. Therefore, there is tremendous variation in the methodologies and assumptions used to determine release levels and doses potentially affecting the health and safety of the public. In some cases, there are three orders of magnitude difference in results for dispersal of similar materials under similar meteorological conditions. To address this issue, the authors have developed an approach to standardizing radiological sabotage target analysis that starts by addressing basic assumptions and then directs the user to some recommended computerized analytical tools. Results from different dispersal codes are also compared in this analysis.

The ASSESS Neutralization Analysis module (Neutralization) is part of Analytic System and Software for Evaluation of Safeguards and Security, ASSESS, a vulnerability assessment tool. Neutralization models a fire fight engagement between security inspectors (SIs) and adversaries. Since version 1.0 of Neutralization was released in 1989, experience has shown that several features of the user interface should be improved. This report describes the improvements that have been implemented, which simplify operation by consolidating all capabilities under a single mode of operation, remove many restrictions on editing, and concentrate more information into fewer types of printed reports. Every adversary and SI combatant is named and described individually. Time to communicate orders is specified for each SI combatant. Adversaries and SIs can be reinforced. SI posting as well deployment destination is labeled. Scenario details can be revised without losing all completed event information. New on-screen summaries spell out characteristics, minimizing abbreviations. Neutralization will read files created by the previous version and permit the user to enter the additional labels supported in the new version. As described here, Neutralization now has an interface that handles more information, but is easier and faster to use.

Short communication.

This paper describes a passive tamper-indicating secure container that has been designed to demonstrate concepts, features, and materials that can be used in passive container applications. (In a passive security system, physical phenomena provide visual indication of tampering.) The basic container {open_quotes}volume within a volume{close_quotes} assembly consists of a transparent plastic outer container and an aluminum inner container. Both containers incorporate passive, fingerprinted layers as part of the tamper-indicating container system. Many of the tamper-indicating features can be visually inspected without disassembling the container. The status of container development and potential applications for the container are addressed.

A radiological safety evaluation is performed to determine the impacts of Exploratory Studies Facility (ESF) design changes on the preclosure public radiological safety for a potential nuclear waste repository at Yucca Mountain, Nevada. Although the ESF design has undergone significant modification, incorporation of the modified design requires only modest changes to the conceptual repository configuration. To the extent feasible, the results of earlier safety evaluations presented in SAND84-2641, SAND88-7061, and SAND89-7024, which were based on the original ESF configuration, are compared with the results for the modified configuration. This comparison provides an estimate of the range of analysis uncertainty. This preliminary analysis indicates that there are no Q-scenarios, which are defined as those scenarios with a net occurrence probability of greater than 10{sup {minus}6}/yr and produce a radiological dose at the 5-km controlled area boundary of greater than 0.5 rem. The analysis yielded estimates for an underground accident of a probability of 3.8 {times} 10{sup {minus}15}/yr and a dose of 1.5 rem. For a surface-initiated accident, a probability of 1.5 {times} 10{sup {minus}12}/yr and a dose of 0.6 rem was estimated.

Tunnels buried deep within the earth constitute an important class geomechanics problems. Two numerical techniques used for the analysis of geomechanics problems, the finite element method and the boundary element method, have complementary characteristics for applications to problems of this type. The usefulness of combining these two methods for use as a geomechanics analysis tool has been recognized for some time, and a number of coupling techniques have been proposed. However, not all of them lend themselves to efficient computational implementations for large-scale problems. This report examines a coupling technique that can form the basis for an efficient analysis tool for large scale geomechanics problems through the use of an iterative equation solver.

Human Instrusion into the potential repository at Yucca Mountain, Nevada, was modeled in the Total-System Performance Assessment (``TSPA-91``) recently completed for the Yucca Mountain Site Characterization Project Office of the DOE. The scenario model assumed that the repository would be penetrated at random locations by a number of boreholes drilled using twentieth-century rotary drilling techniques.

This report brings into focus the results of numerous studies that have addressed issues associated with the validity of assumptions which are used to justify reducing the dimensionality of numerical calculations of water flow through Yucca Mountain, NV. it is shown that, in many cases, one-dimensional modeling is more rigorous than previously assumed.

Sandia National Laboratories was requested to establish the FAA Aging Aircraft Nondestructive Inspection (NDI) Development and Demonstration Center. The Center is housed in a hangar at the Albuquerque International Airport and owns its own aged transport airplane. The Center`s work encompasses research and development in enhanced structural inspection. The goals of the Center are to: promote NDI technology development and maturation; help transfer new nondevelopment item technology to the hangar floor; validate NDI techniques; assess reliability or probability of detection of NDI processes. An important part of this project will be to make sure that the cost of implementation and operation of any technique is seriously considered and that techniques are usable in the field. Among the initial techniques to be evaluated are: enhanced visual, magneto-optic eddy current; coherent optics; ultrasonics; thermographics; eddy current scanners; experimental modal analysis. This project is a perfect example of how Development Testing draws on its own resources and teams up with others, as necessary, to get the job done. In this case, New Mexico State University and a private company, Science Applications International Corporation, are assisting.

This cautionary paper reminds users of quartz shock stress gauges that sensors that ignore the design rules of the ``Sandia quartz gauge`` may produce substantial and unrecognized deviations from normal sensitivity, waveform distortion, and anomalous conduction. Each deviant design must be extensively characterized. The consequence of non-standard gauge designs, like the ``shorted quartz gauge`` designs, are given for prompt response to pulsed radiation while stressed.

PVDF piezoelectric polymer shock stress sensors have been used to measure the shock and impulse generated by soft X-rays and by filter debris in the SATURN Plasma Radiation Source at Sandia National Laboratories, NM. SATURN was used to generate 30 to 40 kJ, 20-ns duration, line radiation at 2 to 3 keV. Fluence on samples was nominally 40, 200, and 400 kJ/m{sup 2} (1, 5, and 10 cal/cm{sup 2}). Measurements of X-ray induced material shock response exposing both aluminum and PMMA acrylic samples agree well with companion measurements made with single crystal X-cut quartz gauges. Time-of-flight, stress, and impulse produced by Kimfol (polycarbonate/aluminum) filter debris were also measured with the PVDF gauges.

PVDF shock stress sensors were subjected to X-ray deposition at nominal absorbed levels of 1, 1{1/2}, 3, and 5 cal/gm (SiO{sub 2} equiv.) and to neutron fluence above 10{sup 13} n/cm{sup 2} while stressed at a peak level of about 2 GPa. Moderate transitory electrical noise that occurred briefly during the radiation did not persist. PVDF shock sensors with aluminum electrodes appear satisfactory for measurement within these exposure limits. Reference quartz gauges were severely affected.

Sandia National Laboratories has the qualification evaluation responsibility for the design of certain components intended for use in nuclear weapons. Specific techniques in assurance and assessment have been developed to provide the quality evidence that the software has been properly qualified for use. Qualification Evaluation is a process for assessing the suitability of either a process used to develop or manufacture the product, or the product itself. The qualification process uses a team approach to evaluating a product or process, chaired by a Quality Assurance professional, with other members representing the design organization, the systems organization, and the production agency. Suitable for use implies that adequate and appropriate definition and documentation has been produced and formally released, adequate verification and validation activities have taken place to ensure proper operation, and the software product meets all requirements, explicitly or otherwise.

Upon achieving ignition and gain, the Laboratory Microfusion Facility (LMF) will be a major tool for Inertial Confinement Fusion (ICF) research and defense applications. Our concept for delivering {approximately}10 MJ with a peak on-target light ion power of {approximately}700 TW involves a multi-modular approach using an extension of the compact inductively isolated cavity and Magnetically Insulated Transmission Line (MITL) Voltage Adder technology that is presently being used in several large accelerators at Sandia/New Mexico. The LMF driver design consists of twelve 8-TW and twelve 38-TW accelerating modules, each with a triaxial MITL/Adder that delivers power to a two stage ion extraction diode. The desired energy, power pulse shape, and deposition uniformity on an ICF target can be achieved by controlling the energy and firing sequence of the ``A`` and ``B`` accelerator modules, plus optimizing the beam transport and focusing. The multi-modular configuration reduces risk by not scaling significantly beyond existing machines and offers the flexibility of staged construction. It permits modular driver testing at the full operating level required by the LMF.

Reconsolidated salt is a fundamental component of the permanent seals for the Waste Isolation Pilot Plant. As regulations are currently understood and seal concepts envisioned, emplaced salt is the sole long-term seal component designed to prevent the shafts from becoming preferred pathways for rating gases or liquids. Studies under way in support of the sealing function of emplaced salt include laboratory testing of crushed salt small-scale in situ tests, constitutive modeling of crushed salt, calculations of the opening responses during operation and closure, and design practicalities including emplacement techniques. This paper briefly summarizes aspects of these efforts and key areas of future work.

In the verification technology arena, there is a pressing need for surveillance and monitoring equipment that produces authentic, verifiable records of observed activities. Such a record provides the inspecting party with confidence that observed activities occurred as recorded, without undetected tampering or spoofing having taken place. The secure authenticated video equipment (SAVE) system provides an authenticated series of video images of an observed activity. Being self-contained and portable, it can be installed as a stand-alone surveillance system or used in conjunction with existing monitoring equipment in a non-invasive manner. Security is provided by a tamper-proof camera enclosure containing a private, electronic authentication key. Video data is transferred communication link consisting of a coaxial cable, fiber-optic link or other similar media. A video review station, located remotely from the camera, receives, validates, displays and stores the incoming data. Video data is validated within the review station using a public key, a copy of which is held by authorized panics. This scheme allows the holder of the public key to verify the authenticity of the recorded video data but precludes undetectable modification of the data generated by the tamper-protected private authentication key.

A multiphase mixture model is presented to describe shock compression of highly porous, multi-component powders. Volume fractions are represented as independent kinematic variables and thermodynamically-admissible phase interaction constitutive models are formulated in the context of a three phase system. Numerical solutions of the multiphase flow equations simulated impact on a porous layer of mixed powders of Al and Fe{sub 2}O{sub 3}. The multiphase model predicts dispersive compaction waves which have features similar to observed time-resolved pressure measurements.

GENSHELL is a three-dimensional shell mesh generation program. The three-dimensional shell mesh is generated by mapping a two-dimensional quadrilateral mesh into three dimensions according to one of several types of transformations: translation, mapping onto a spherical, ellipsoidal, or cylindrical surface, and mapping onto a user-defined spline surface. The generated three-dimensional mesh can then be reoriented by offsetting, reflecting about an axis, revolving about an axis, and scaling the coordinates. GENSHELL can be used to mesh complex three-dimensional geometries composed of several sections when the sections can be defined in terms of transformations of two-dimensional geometries. The code GJOIN is then used to join the separate sections into a single body. GENSHELL updates the EXODUS quality assurance and information records to help track the codes and files used to generate the mesh. GENSHELL reads and writes two-dimensional and three-dimensional mesh databases in the GENESIS database format; therefore, it is compatible with the preprocessing, postprocessing, and analysis codes in the Sandia National Laboratories Engineering Analysis Code Access System (SEACAS).

1990 amendments to the Clean Air Act have created the need for instruments capable of monitoring volatile organic compounds (VOCS) in public air space in an unattended and low cost manner. The purpose of the study was to develop and demonstrate the capability to do long term automatic and unattended ambient air monitoring using an inexpensive portable analytic system at a commercial manufacturing plant site. A gas chromatograph system personal computer hardware, meteorology tower & instruments, and custom designed hardware and software were developed. Comparison with an EPA approved method was performed. The system was sited at an aircraft engines manufacturing site and operated in a completely unattended mode for 60 days. Two VOCs were monitored every 30 minutes during the 24hr day. Large variation in the concentration from 800ppb to the limits of detection of about 10ppb were observed. Work to increase the capabilities of the system is ongoing.

Interest in launching payloads through the atmosphere to ever higher velocity is robust. For hundreds of years, guns and rockets have been improved for this purpose until they are now considered to be near to their performance limits. While the potential of electromagnetic technology to increase launch velocity has been known since late in the nineteenth century, it was not until about 1980 that a sustained and large-scale effort was started to exploit it. Electromagnetic launcher technology is restricted here to mean only that technology which establishes both a current density, J, and a magnetic field, B, within a part of the launch package, called the armature, so that J {times} B integrated over the volume of the armature is the launching force. Research and development activity was triggered by the discovery that high velocity can be produced with a simple railgun which uses an arc for its armature. This so called ``plasma-armature railgun`` has been the launcher technology upon which nearly all of the work has focused. Still, a relatively small parallel effort has also been made to explore the potential of electromagnetic launchers which do not use sliding contacts on stationary rails to establish current in the armature. One electromagnetic launcher of this type is called an induction coilgun because armature current is established by electromagnetic induction. In this paper, we first establish terminology which we will use not only to specify requirements for successful endoatmospheric launch but also to compare different launcher types. Then, we summarize the statuses of the railgun and induction coilgun technologies and discuss the issues which must be resolved before either of these launchers can offer substantial advantage for endoatomospheric launch.

To analyze the vulnerability of nuclear materials to theft or sabotage, Department of Energy facilities have been using, since 1989, a computer program called ASSESS, Analytic System and Software for Evaluation of Safeguards and Security. During the past year Sandia National Laboratories has began using an additional program, SEES, Security Exercise Evaluation Simulation, enhancing the picture of vulnerability beyond what either program achieves alone. ASSESS analyzes all possible paths of attack on a target and, assuming that an attack occurs, ranks them by the probability that a response force of adequate size can interrupt the attack before theft or sabotage is accomplished. A Neutralization module pits, collectively, a security force against the interrupted adversary force in a fire fight and calculates the probability that the adversaries are defeated. SEES examines a single scenario and simulates in detail the interactions among all combatants. Its output includes shots fired between shooter and target, and the hits and kills. Whereas ASSESS gives breadth of analysis, expressed statistically and performed relatively quickly, SEES adds depth of detail, modeling tactical behavior. ASSESS finds scenarios that exploit the greatest weaknesses of a facility. SEES explores these scenarios to demonstrate in detail how various tactics to nullify the attack might work out. Without ASSESS to find the facility weaknesses, it is difficult to focus SEES objectively on scenarios worth analyzing. Without SEES to simulate the details of response vs. adversary interaction, it is not possible to test tactical assumptions and hypotheses. Using both programs together, vulnerability analyses achieve both breadth and depth.

To analyze the vulnerability of nuclear materials to theft or sabotage, Department of Energy facilities have been using, since 1989, a computer program called ASSESS, Analytic System and Software for Evaluation of Safeguards and Security. During the past year Sandia National Laboratories has begun using an additional program, SEES, Security Exercise Evaluation Simulation, enhancing the picture of vulnerability beyond what either program achieves alone. Assess analyzes all possible paths of attack on a target and, assuming that an attack occurs, ranks them by the probability that a response force of adequate size can interrupt the attack before theft or sabotage is accomplished. A Neutralization module pits, collectively, a security force against the interrupted adversary force in a fire fight and calculates the probability that the adversaries are defeated. SEES examines a single scenario and simulates in detail the interactions among all combatants. its output includes shots fired between shooter and target, and the hits and kills. Whereas ASSESS gives breadth of analysis, expressed statistically and performed relatively quickly, SEES adds depth of detail, modeling tactical behavior. ASSESS finds scenarios that exploit the greatest weakness of a facility. SEES explores these scenarios to demonstrate in detail how various tactics to nullify the attack might work out. Without ASSESS to find the facility weakness, it is difficult to focus SEES objectively on scenarios worth analyzing. Without SEES to simulate the details of response vs. adversary interaction, it is not possible to test tactical assumptions and hypotheses. Using both programs together, vulnerability analyses achieve both breadth and depth.

Anomalous features in Gulf Coast Salt domes exhibit deviations from normally pure salt and vary widely in form from one dome to the next, ranging considerably in length and width. They have affected both conventional and solution mining in several ways. Gas outbursts, insolubles, and potash (especially carnallite) have led to the breakage of tubing in a number of caverns, and caused irregular shapes of many caverns through preferential leaching. Such anomalous features essentially have limited the lateral extent of conventional mining at several salt mines, and led to accidents and even the closing of several other mines. Such anomalous features, are often aligned in anomalous zones, and appear to be related to diapiric processes of salt dome development. Evidence indicates that anomalous zones are found between salt spines, where the differential salt intrusion accumulates other materials: Anhydrite bands which are relatively strong, and other, weaker impurities. Shear zones and fault displacement detected at Big Hill and Weeks Island domes have not yet had any known adverse impacts on SPR oil storage, but new caverns at these sites conceivably may encounter some potentially adverse conditions. Seismic reflection profiles at Big Hill dome have shown numerous fractures and faults in the caprock, and verified the earlier recognition of a major shear zone transecting the entire salt stock and forming a graben in the overlying caprock. Casing that is placed in such zones can be at risk. Knowledge of these zones should create awareness of possible effects rather than preclude the future emplacement of caverns. To the extent possible, major anomalous zones and salt stock boundaries should be avoided. Shear zones along overhangs may be particularly hazardous, and otherwise unknown valleys in the top of salt may occur along shear zones. These zones often can be mapped geophysically, especially with high-resolution seismic techniques.

Sandia National Laboratories and Los Alamos National Laboratory have been designated as the technical lead for Security, Safeguards and Computer/Information Security systems for all the DOE Complex 21/Weapons Complex Reconfiguration (WCR) facilities. The physical protection systems in these facilities will be required to meet the most current DOE orders and incorporate the latest physical protection technologies, proven state-of-the-art systems and strategies. The planned approach requires that security assistance and information be provided to the designers (e.g. the Complex 21 Architect & Engineer and the Weapons Complex Lead Laboratories) as early as possible and throughout all design phases. The outcome should avoid the costly retrofits to existing facilities that have occurred in the past and result in effective and comprehensive protection against current and projected threats with minimal impact on operations, safety and costs. This paper discusses the physical protection considerations being promoted for the integrated design effort for the Complex 21/Reconfiguration facilities, such as the tritium, uranium/lithium, plutonium processing and storage, high explosive and assembly and disassembly facilities.

The purpose of this report is to summarize the status of computational analysis of hypervelocity impact lethality in relatively nontechnical terms from the perspective of the author. It is not intended to be a review of the technical literature on the problems of concern. The discussion is focused by concentrating on two phenomenology areas which are of particular concern in computational impact studies. First, the material`s equation of state, specifically the treatment of expanded states of metals undergoing shock vaporization, is discussed. Second, the process of dynamic fragmentation is addressed. In both cases, the context of the discussion deals with inaccuracies and difficulties associated with numerical hypervelocity impact simulations. Laboratory experimental capabilities in hypervelocity impact for impact velocities greater than 10.0 km/s are becoming increasingly viable. This paper also gives recommendations for experimental thrusts which utilize these capabilities that will help to resolve the uncertainties in the numerical lethality studies that are pointed out in the present report.

Current classified document management systems require a tremendous amount of space and extensive manpower to account for, inventory, and protect the documents. Comprehensive analysis of current control and accountability procedures reveal the main problem is the actual handling of the paper itself. The purpose of the Networked Microsoft Windows 3.1 based Classified Document Control System (CDOCS) is to eliminate the paper by scanning and storing images of pages on a personal computer using {open_quotes}write once read mostly{close_quotes} (WORM) high density optical media. By saving images on the computer, not only can manpower and space requirements be reduced, but the chance of compromise is diminished. As an added benefit, the information is now more readily available to the authorized user and is provided to the user at the user`s PC. The network target for CDOCS is Microsoft Windows for Workgroups. Thus, the system is also readily applicable to unclassified document imaging uses.

Information system requirements that are expressed as simple English sentences provide a clear understanding of what is needed between system specifiers, administrators, users, and developers of information systems. The approach used to develop the requirements is the Natural-language Information Analysis Methodology (NIAM). NIAM allows the processes, events, and business rules to be modeled using natural language. The natural language presentation enables the people who deal with the business issues that are to be supported by the information system to describe exactly the system requirements that designers and developers will implement. Computer prattle is completely eliminated from the requirements discussion. An example is presented that is based upon a section of a DOE Order involving nuclear materials management. Where possible, the section is analyzed to specify the process(es) to be done, the event(s) that start the process, and the business rules that are to be followed during the process. Examples, including constraints, are developed. The presentation steps through the modeling process and shows where the section of the DOE Order needs clarification, extensions or interpretations that could provide a more complete and accurate specification.

Transparent and secure process monitoring systems may become an important tool in the dismantlement schemes in support of bilateral and multi-lateral treaties. A prototype system, using public key cryptography to authenticate compliance data, has been developed by Sandia National Laboratories. The Authenticated In-plant Process Monitor (AIPM) is an embedded process monitoring system capable of accepting up to sixteen industry standard process variables, at sample rates of up to two samples per second. Each AIPM will synchronously sample the process, authenticate, and transmit the data in real-time to the host receiving station. The receiving station will validate the compliance data and then display in real-time while updating a relational database. This new generation of monitoring systems must include protection from a host of possible threat scenarios while providing the user authentic clear text data. Data threats are controlled by the use of a public key Treaty Data Authentication Module (TDAM) utilizing the National Institute of Standards and Technology (NIST) Digital Signature Standard. System threats are minimized by the use of a tamper indicating enclosure that monitors unauthorized entry and environmental attacks. Insider threats will be controlled by the use of an authenticated bi-directional communication link between each remote AIPM and the host receiving station. This security envelope will be monitored on a real-time basis with appropriate action taken if an attack occurs. The employment of these security features allows the inspectorate to distribute unprocessed clear text data and an attached digital signature with confidence that the data cannot be forged.

Information Surety is the enhancement of the confidentiality, integrity, and availability of information and software systems. It is attained through sequential steps: identification of software reliability requirements and information protection needs, designing for a balanced level of risk throughout the system, and application of appropriate software and hardware technologies and procedures. The ability to apply these steps when developing systems is impaired by a general lack of understanding of surety issues by system developers, and by the fact that there are many separate areas of knowledge involved that are not currently integrated into a disciplined approach (e.g., risk assessment, information access control in computers and networks, secure messaging, trusted software development). Our best systems today are achieved by clever designers who use ad-hoc methods. In the absence of good development tools, technologies may be applied haphazardly and/or retrofitted, without yielding balanced protection. This paper will take the audience through an exploration of the elements of information surety, some common misconceptions about information surety today, and the even greater challenges on the horizon. It will end with some suggestions for research areas which will help evolve the discipline of information surety.

Sandia National Laboratories has considerable experience with monochrome video monitors used in alarm assessment video systems. Most of these systems, used for perimeter protection, were designed to classify rather than to identify intruders. There is a growing interest in the identification function of security video systems for both access control and insider protection. Because color video technology is rapidly changing and because color information is useful for identification purposes, Sandia National Laboratories established a program to evaluate the newest relevant color video equipment. This report documents the evaluation of an integral component, color monitors. It briefly discusses a critical parameter, dynamic range, details test procedures, and evaluates the results.

International Atomic Energy Agency (IAEA) inspectors must maintain continuity of knowledge on all safeguard samples and, in particular, on those samples drawn from plutonium product and spent fuel input tanks at a nuclear reprocessing plant`s blister sampling station. Integrity of safeguard samples must be guaranteed from the sampling point to the moment of sample analysis at an accepted local laboratory or at the IAEA`s Safeguards Analytical Laboratory (SAL) in Seibersdorf, Austria. The safeguard samples are drawn at a blister sampling station with inspector participation and then transferred via a pneumatic post system to the facility`s analytical laboratory. Transfer of the sample by the pneumatic post system, arrival of the sample in the operator`s analytical laboratory, and storage of the sample awaiting analysis are very time consuming activities for an inspector, particularly if continuous human surveillance is required for all these activities. These activities could be observed by ordinary surveillance methods, such as a video monitoring system, but this would be cumbersome and time consuming for both the inspector and the operator. This paper describes a secure container designed to assure sample vial integrity from the point the sample is drawn to treatment of the sample at a facility`s analytical laboratory.

The progress made in advanced packaging development at Sandia National Laboratories for integration of III-V photonic devices and CMOS IC`s on Silicon MCM substrates for planar aid stacked applications will be reported. Studies to characterize precision alignment techniques using solder attach materials compatible with both silicon IC`s and III-V devices will be discussed. Examples of the use of back-side alignment and IR through-wafer inspection will be shown along with the extra processing steps that are used. Under bump metallurgy considerations are also addressed.

A simplified explanation for gas flow instability in parallel heated channels is presented with specific applications to channels containing packed beds of power-producing particles. The explanation captures the basic governing physics of the viscosity-driven instability and hopefully removes some of the misconceptions surrounding this issue. Simple illustrative calculations, steady-state and transient, using the SAFSIM computer program are included in the explanation. The explanation points out that flow instability is common to any and all gas flow systems with parallel heated channels, that the addition of flow resistance to the entrance of a channel mitigates flow instability, and that instabilities do not occur instantaneously.

The design of a magnetically suspended six degree of freedom positioning system capable of nanometer positioning is presented. The sample holder is controlled in six degrees of freedom (DOF) over 300 micrometers of travel in X, Y and Z directions. A design and control summary, and test results indicating stability and power dissipation are included in the paper. The system is vacuum compatible, uses commercially available materials, and requires minimal assembly and setup.

Concepts for underground panel or drift seals at the Waste Isolation Pilot Plant are developed to satisfy sealing requirements of the operational period. The concepts are divided into two groups. In the ``NOW`` group, design concepts are considered in which a sleeve structure is installed in the panel access immediately after excavation and before waste is emplaced. In the ``LATER`` group, no special measures are taken during excavation or before waste emplacement; the seal is installed at a later date, perhaps up to 35 years after the drift is excavated. Three concepts are presented in both the NOW and LATER groups. A rigid sleeve, a yielding sleeve, and steel rings with inflatable tubes are proposed as NOW concepts. One steel ring concept and two concrete monoliths are proposed for seals emplaced in older drifts. Advantages and disadvantages are listed for each concept. Based on the available information, it appears most feasible to recommend a LATER concept using a concrete monolith as a preferred seal for the operational period. Each concept includes the potential of remedial grout and/or construction of a chamber that could be used for monitoring leakage from a closed panel during the operational period. Supporting in situ demonstrations of elements of the concepts are recommended.

An investigation of the shock compression and release properties of silicon carbide ceramic has been performed. A series of planar impact experiments has been completed in which stationary target discs of ceramic were struck by plates of either similar ceramic or other appropriate material at velocities up to 2.2 km/s with a propellant gun facility. The particle velocity history at the interface between the back of the target ceramic and a lithium-fluoride window material was measured with laser velocity interferometry (VISAR). Impact stresses achieved in these experiments range between about 10 and 50 GPa. Numerical solutions and analytic methods were used to determine the dynamic compression and release stress-strain behavior of the ceramic. Further analysis of the data was performed to determine dynamic strength and compressibility properties of silicon carbide.

A joint US/Federal Republic of Germany (FRG) project has successfully tested a unique solar-driven chemical reactor in the CAtalytically Enhanced Solar Absorption Receiver (CAESAR) experiment. The CAESAR test was a {open_quotes}proof-of-concept{close_quotes} demonstration of carbon-dioxide reforming of methane in a commercial-scale, solar, volumetric receiver/reactor on a parabolic dish concentrator. The CAESAR design; test facility and instrumentation; thermal and chemical tests; and analysis of test results are presented in detail. Numerical models for the absorber and the receiver are developed and predicted performance is compared with test data. Post test analyses to assess the structural condition of the absorber and the effectiveness of the rhodium catalyst are presented. Unresolved technical issues are identified and future development efforts are recommended.

This report describes work performed at Sandia under a CRADA with Shell Development of Houston, Texas aimed at developing hydrous metal oxide (HMO) catalysts for oxidation of hydrocarbons. Autoxidation as well as selective oxidation of 1-octene was studied in the presence of HMO catalysts based on known oxidation catalysts. The desired reactions were the conversion of olefin to epoxides, alcohols, and ketones, HMOs seem to inhibit autoxidation reactions, perhaps by reacting with peroxides or radicals. Attempts to use HMOs and metal loaded HMOs as epoxidation catalysts were unsuccessful, although their utility for this reaction was not entirely ruled out. Likewise, alcohol formation from olefins in the presence of HMO catalysts was not achieved. However, this work led to the discovery that acidified HMOs can lead to carbocation reactions of hydrocarbons such as cracking. An HMO catalyst containing Rh and Cu that promotes the reaction of {alpha}-olefins with oxygen to form methyl ketones was identified. Although the activity of the catalyst is relatively low and isomerization reactions of the olefin simultaneously occur, results indicate that these problems may be addressed by eliminating mass transfer limitations. Other suggestions for improving the catalyst are also made. 57 refs.

A mission hazard assessment has been performed for the Strategic Target System Mission 1 (known as STARS M1) for hazards due to potential debris impact in the Marshall Islands area. The work was performed at Sandia National Laboratories as a result of discussion with Kwajalein Missile Range (KMR) safety officers. The STARS M1 rocket will be launched from the Kauai Test Facility (KTF), Hawaii, and deliver two payloads to within the viewing range of sensors located on the Kwajalein Atoll. The purpose of this work has been to estimate upper bounds for expected casualty rates and impact probability or the Marshall Islands areas which adjoin the STARS M1 instantaneous impact point (IIP) trace. This report documents the methodology and results of the analysis.

This Fire Hazards Analysis is sponsored by Plant Engineering and is prepared to support the Safety Assessment for the CNSAC Facility. This is a preliminary fire hazards analysis of a yet to be constructed facility and is based upon the current building design and the current understanding of the potential occupancy hazards. The governing occupancy for this building is personnel offices. The CNSAC facility will be dedicated primarily to two activities: (1) arms control and verification technology and (2) intelligence. This report supplements the Safety Assessment for the CNSAC facility and follows the guidance of DOE Memorandum EH-31.3 and meets the objectives of paragraph 4 of DOE Order 5480.7A, ``Fire Protection.`` This analysis demonstrates that under ``worst case`` assumptions a fire in the CNSAC facility will result in consequences which are below DOE offsite guidelines for accident conditions. This report is based upon preliminary design information and any major changes to the building design may require additional analyses.

The Salado Two-Phase Flow Laboratory Program was established to address concerns regarding two-phase flow properties and to provide WIPP-specific, geologically consistent experimental data to develop more appropriate correlations for Salado rock to replace those currently used in Performance Assessment models. Researchers in Sandia`s Fluid Flow and Transport Department originally identified and emphasized the need for laboratory measurements of Salado threshold pressure and relative permeability. The program expanded to include the measurement of capillary pressure, rock compressibility, porosity, and intrinsic permeability and the assessment of core damage. Sensitivity analyses identified the anhydrite interbed layers as the most likely path for the dissipation of waste-generated gas from waste-storage rooms because of their relatively high permeability. Due to this the program will initially focus on the anhydrite interbed material. The program may expand to include similar rock and flow measurements on other WIPP materials including impure halite, pure halite, and backfill and seal materials. This conceptual plan presents the scope, objectives, and historical documentation of the development of the Salado Two-Phase Flow Program through January 1993. Potential laboratory techniques for assessing core damage and measuring porosity, rock compressibility, capillary and threshold pressure, permeability as a function of stress, and relative permeability are discussed. Details of actual test designs, test procedures, and data analysis are not included in this report, but will be included in the Salado Two-Phase Flow Laboratory Program Test Plan pending the results of experimental and other scoping activities in FY93.

Sandia National Laboratories maintains several libraries of equation of state tables, in a modified Sesame format, for use in hydrocode calculations and other applications. This report discusses one of those libraries, the seslan file, which contains 78 tables from the Los Alamos equation of state library. Minor changes have been made to these tables, making them more convenient for code users and reducing numerical difficulties that occasionally arise in hydrocode calculations.

The ANSI/ANS 8.1 criticality safety standard recommends validation and benchmarking of the calculational methods used in evaluating criticality safety limits for away-from-reactor applications. The lack of critical experiments with burned light-water reactor (LWR) fuel in racks or in casks necessitates the validation of burnup credit methods by comparison with LWR core criticals. These benchmarks are relevant because they test a methodology`s ability to predict spent fuel isotopic and to evaluate the reactivity effects of heterogeneities and strong absorbers. Data are available to perform analyses at precise state points. As part of the Burnup Credit Analysis Verification (BCAV) Task, the U.S. Department of Energy has sponsored analysis of selected reactor core critical configurations from commercial pressurized-water-reactors (PWRs). The initial analysis methodology used the SCALE-4 code system to analyze a set of reactor critical configurations from Virginia Power`s Slurry and North Anna reactors. However, the analysis procedure was complex and included the calculation of lumped fission products. The methodology has since been revised to simplify both the data requirements and the calculational procedure for the criticality analyst. This revised methodology is validated here by a comparison with three reactor critical configurations from Tennessee Valley Authority`s Sequoyah Unit 2 Cycle 3 and two from Virginia Power`s Slurry Unit 1 Cycle 2.

The current political and economic situations suggest that significant reductions of nuclear forces outside the US will continue. This implies that in times of crisis the rapid deployment of nuclear weapons into a theater may be required. This paper describes a proposed Mobile Integrated C{sup 3} and Security System (MICSS). The MICSS, together with associated personnel, could satisfy the command and control and security requirements of a deployed nuclear operation. Rapid deployment poses unique nuclear weapon surety difficulties that must be overcome for the operation to be effective and survivable. The MICSS must be portable, reliable, limited in size, and easily emplaced to facilitate movement, reduce the possibility of detection, and minimize manpower requirements. The MICSS will be based on existing technology. Sandia has designed prototype mobile command centers for the military. These command centers are based on an approach that stresses modularity, standards, and the use of an open architecture. Radio, telephone, satellite communications, communication security, and global positioning system equipment has been successfully integrated into the command centers. Sandia is also supporting the development of portable security systems for the military. These systems are rapidly deployable and mission flexible and are capable of intrusion detection, area and alarm display, night assessment, and wireless sensor communications. This paper is organized as follows: Background information about the prototype mobile command centers will be presented first. Background information about portable security systems concepts will then be given. Next, an integrated communications and security system will be presented, and finally, the design and status of a prototype MICSS will be described.