Publications

An understanding of dispersal of nuclear materials from an explosive event is needed to support design studies of weapon storage and transportation. Assessing the consequences and requirements for cleanup of a fire or nonnuclear detonation of a system containing nuclear material requires knowledge of the aerosol formation process. Information about the aerosol chemical composition, the physical size and shape of the particulates, as well as the efficiency of aerosol formation ate needed to conduct meaningful assessments. This report describes laboratory tests to study aerosol from materials of interest. An electromagnetic launcher is used to heat and propel molten metallic samples under energetic high-velocity conditions. We describe the apparatus and first results from tests using uranium-molybdenum alloy samples. Contained laboratory-scale measurements are described that determine aerosol morphology, chemical composition, and aerosol formation efficiency under high-velocity conditions. Data from the launcher tests describe (1) the aerodynamic breakup process of high-velocity molten liquid into droplets, and (2) the formation of still finer aerosols by combustion of these droplets at high velocity. The measurements show efficient aerosol production in air that is dominated by the formation of fine chain-agglomerate combustion aerosol. Particle morphology information for both the chain agglomerate and the less common liquid breakup products is described. The aerodynamic breakup of the liquid sample material is described. Lognormal distributions are shown to accurately represent the data. The geometric mean diameter is related to the mass mean diameter and maximum stable droplet diameter for the distributions. 28 refs., 27 figs., 3 tabs.

Several potential incident scenarios involving the accidental release of radioactive material at five reference, nonreactor nuclear material licensees are analyzed in this report. The economic risk ($/licensee/yr) of decontamination is evaluated for each reference licensee. Although most releases and cleanup costs are minor, some less frequent incidents may result in very high cleanup costs that dominate the economic risk of decontamination of a particular licensee. The economic risk for the 5 plants ranged from a low of $14,000 per licensee per year to a high of $104,000 per licensee per year. This report is the second of two reports by Sandia National Laboratories on the economic risk of nonreactor nuclear material licensee operations. 40 refs., 21 figs., 31 tabs.

Both the US Environmental Protection Agency (EPA) and the US Nuclear Regulatory Commission (NRC) have promulgated regulations regarding the performance of geologic repositories for the disposal of high-level nuclear waste. One of the responsibilities of the US Department of Energy (DOE) is to demonstrate compliance with the appropriate regulations. The DOE will most likely use extensive numerical modeling to show compliance with the various quantitative requirements. These analyses will then be evaluated by the NRC. There are different levels of evaluation: peer review, conservative estimates,used of existing models/codes, and development of models/codes by the NRC. The intensity of the review will vary from analysis to analysis, depending on the importance of the analysis, the acceptability of the conceptual model behind the analysis and the solution technique used, and the potential for increasing confidence in the system description, should the NRC decide to develop its own models/codes. An appropriate level of review can be determined by applying these four criteria in a specific manner. 24 refs.

This report examines the computational implementation of a continuum model for jointed rock media. The jointed rock model uses strain partitioning between the elastic rock matrix and joint sets with nonlinear normal and shear responses. A specific model using a rational polynomial to describe normal joint response was first used as the basis for a computational implementation of a jointed rock model for two-dimensional problems. This particular implementation can be extended to three dimensions, but it would be a very expensive material model from a computational standpoint. The problem of trying to implement a joint model in three dimensions so that it would not be an extremely expensive computational tool has led to a study of various computational implementations of joint models for two-dimensional geometries. These studies have produced implementations of joint models that are very computationally efficient and that can handle joint models with normal joint behavior described by general relations. The implementations studied in this report make the use of jointed rock models in three dimensions much more feasible in terms of computational expense. 6 refs., 8 figs., 2 tabs.

Thermal imagers are effective tools for detecting aggressive actions and enhancing physical security in both tactical and peacetime environments. However, from an operator's perspective, these devices are rarely used on a continuous basis because of inconvenience and a requirement to have the operator be the detector'' while using the imager as a sensor. This paper describes an area sensor and assessment system designed to reduce operator fatigue and improve the effectiveness of costly thermal imagers. Several prototypes have been installed and operated at sites worldwide. The device uses a thermal imager as the primary sensor but also incorporates a laser rangefinder, automatic area precision scanning, robust scan-to-scan scene change detection, a deliberate-motion detection features. The system setup, control, and alarm assessment functions of the operator console are described. The digital processing is discussed and performance measures are given. 2 refs., 7 figs.

This report describes the development of the following new catalytic materials based on hydrous metal oxide (HMO) ion exchange materials: Na-Ti, Nb, Zr, and mixtures of hydrated silica with hydrous Ti-oxide. HMO's provide a versatile system for the preparation of heterogeneous catalysts. The preparation chemistry allows synthesis of catalysts that can be tailored to particular processes with respect to both chemical and physical properties. Bulk catalysts with surface areas over 300 m{sup 2}/g and pore volumes up to 0.4 cc/g as well as thin films of the HMO materials can be prepared on supports having a wide range of catalytically important physical properties. This report, the first of two parts, presents research performed to date regarding the preparation chemistry, and physical and chemical properties of HMO materials which may be used to develop heterogeneous catalysts for direct coal liquefaction processes. During the course of this work, new ideas for research areas relative to direct coal liquefaction were briefly explored. Two of them that merit further work, catalyst-anchored hydrogen donors and alkoxide-derived crystalline titanate compounds, are briefly described. 25 refs., 34 figs., 8 tabs.

Drillholes H-17 and H-18 were drilled at the WIPP site to assess uncertainties in site hydrologic parameters and to serve as monitoring points for planned hydrologic tests. H-17 was drilled south of H-11 and east of P-17 to evaluate the existence of a high-permeability region in the Culebra Dolomite Member that had been indicated by groundwater-flow modeling and surface geophysical surveys. H-18 was drilled north of H-2 to help reduce the uncertainties of boundaries between high and low transmissivities and fluid density that had been identified by drilling and by modeling. 1 ref., 4 figs., 6 tabs.

An extensive literature review has been conducted as part of an effort to quantify the fidelity of Sandia's lightning burn-through simulation technique. The dominant parameters affecting damage have been identified and are discussed. Two alternative techniques for qualitatively improving the Sandia simulation have been identified, but quantification of the correlation of the results of each with those of natural lightning awaits completion of further experimental work. A systematic set of laboratory experiments is proposed to assess the sensitivity of each technique to key simulation parameters. An available calibration linkage to natural lightning is the reproduction of damage spots that were created by lightning on a set of copper disks mounted on TV towers, and an attempt to do this is included in the proposed experiments. In order to reduce the uncertainties of this approach, more lightning-spot data are required, along with records of the flash currents that produced them. It is recommended that such data be acquired in conjunction with the Rocket-Triggered Lightning Program being conducted each summer at the Kennedy Space Center. 25 refs., 5 figs., 1 tab.

The inverse triax diode is a high power, low impedance electron diode which offers significant advantages over conventional electron diodes on short-pulse (<30 ns FWHM) high power x-ray simulators. Parametric calculations show that the radiation efficiency of the inverse triax is competitive with standard diodes fro mean photon energies below about 120 keV, and sometimes up to 150 keV. Particle-in-cell code simulations show the impedance behavior and flow pattern in the inverse triax with and without the presence of an anode plasma. The simulation results are used to suggest design rules for inverse triax diodes. Experimental results show good agreement with calculations of the impedance behavior and electron beam dynamics. Using inverse triax diodes, we have produced peak doses of 1.4 {times} 10{sup 11} rad(TLD)/s over 840 cm{sup 2} with a mean photon energy of 120 keV on SPEED and 3.1 {times} 10{sup 11} rad(TLD)/s over 3700 cm{sup 2} with a mean photon energy of 140 keV on Saturn. 20 refs., 16 figs.

The BES Materials Science program at Sandia Albuquerque has the central theme of Scientifically Tailored Materials. The major objective of this program is to combine Sandia's expertise and capabilities in the areas of solid state sciences, advanced atomic-level diagnostics and materials-processing science to produce new classes of tailorable materials for the US energy industry, the electronics industry and for defense needs. Current research in this program includes the physics and chemistry of ceramics, the use of energetic particles for the synthesis and study of materials, high-temperature and organic superconductors, tailored surfaces for materials applications, chemical vapor deposition sciences, strained-layer semiconductors, advanced growth techniques for improved semiconductor structures and boron-rich very high temperature semiconductors. A new start just getting underway deals with the atomic level science of interfacial adhesion. Our interdisciplinary program utilizes a broad array of sophisticated, state-of-the-art experimental capabilities provided by other programs. The major capabilities include several molecular-beam epitaxy and chemical-vapor-deposition facilities, electron- and ion-beam accelerators, laser-based diagnostics, advanced surface spectroscopies, unique combined high-pressure/low-temperature/high-magnetic-field facilities, and the soon to be added scanning tunneling and atomic force microscopies.

Calorimetry was performed on Sandia National Laboratories' Test Bed Concentrator {number sign}1 (TBC-1) during late July and early August 1989. The purpose of the tests was to determine the total power available from the concentrator and the amount of the total power that can be focused through a 22-cm aperture plate located at the nominal focal point of the dish. The 22-cm aperture corresponds to the diameter of several reflux receivers that are currently under development, fabrication and testing at Sandia. The calorimeter test will allow the efficiency of the sodium reflux receivers to be calculated. The total power (normalized to 1000 W/m{sup 2}) available from TBC-1 is 66.4 kW into the 22-cm aperture plate. Within error limits, this power level is the same with or without the aperture plate. The power levels stated are for this time (July 1989) and will probably change as the mirrors further degrade. Since the last calorimetry tests were performed, the mirror facets have degraded significantly, and the results presented here support this effect. Finally, three of the 220 facets were missing. 3 refs., 5 figs., 2 tabs.

This report describes research leading to the development of new catalytic materials based on hydrous metal oxide (HMO) ion exchangers. Present in this part, the second of two parts, are results of catalyst-related research and application of the materials to catalytic reactions for direct coal liquefaction processes. HMO materials are inorganic ion exchangers, derived from the alkoxides of Ti, Zr, Nb, or Ta, that exhibit a number of properties applicable to the preparation of catalysts. Research on the catalytic properties of HMO's has focused on the hydrous titanium oxide (HTO) system. However, exploratory coal liquefaction experiments with hydrous niobium oxides (HNO's) and hydrous zirconium oxides (HZO's) have demonstrated that these HMO's also exhibit potential as coal liquefaction catalysts. Studies performed during the course of this research include (1) preliminary coal liquefaction and hydrotreating tests, (2) tests of hydrogenation, hydrodesulfurization, hydrodeoxygenation and hydrodenitrogenation activity using model compounds, (3) development of catalyst pretreatment and activation procedures, (4) modification of HTO supports with silicon, (5) preparation and testing of thin film HTO catalysts, (6) synthesis, characterization and evaluation of base and noble metal catalyst deactivation tests, and (9) exploratory tests of applications other than direct liquefaction. The versatility of the HTO system for synthesis of catalysts allows great potential for further improvements in activity and selectivity as well as tailoring of catalysts for specific processes. Research is continuing in these areas. 54 refs., 63 figs., 25 tabs.

Drillholes H-14 and H-15 were drilled to investigate data gaps in the hydrologic hole distribution at the WIPP site. In addition to the information gained on the Culebra Dolomite Member, the holes yielded hydraulic and/or stratigraphic information on the Forty-niner, Magenta Dolomite, and Tamarisk Members of the Rustler Formation in an era where no such information was available. Hydraulic tests were also conducted on the lower part of the Dewey Lake Redbeds in H-14. A suite of geophysical logs was run on the drillholes and was used to identify different lithologies and aided in the interpretation of the hydraulic tests. 3 refs., 4 figs., 6 tabs.

This report presents a method of running batch jobs from menu-driven interactive EQUEL programs. EQUEL is the embedded query language of INGRES, a popular database management system used widely at Sandia. The method is framed in the VAX/VMS operating system environment.

For more than 10 years, the US Department of Energy's Solar Thermal Program has pioneered the development of heliostats, mirrors that track the sun, for solar central-receiver power plants. The field of heliostats is the single most expensive part of such plants, so their cost must be as low as possible for the technology to be commercially successful. Recent efforts have focused on the development of heliostats that use stretched-membrane reflectors in place of the more familiar glass mirrors. In such heliostats, metal foils are stretched over both sides of a large-diameter metal ring. The reflective surface is a silvered-polymer film glued to the front membrane. A slight vacuum in the space between the two membranes is actively controlled to provide a concave, focused contour to the mirror, and in an emergency this space can be rapidly pressurized to defocus it. Because of their simplicity and lighter weight, stretched- membrane heliostats have the potential to cost significantly less than current glass-mirror designs. The first 50-m{sup 2} mirror modules, built under contract to Sandia in 1986, demonstrated that membrane heliostats could perform at least as well as heliostats using glass mirrors. Insights gained from Sandia's testing and evaluation of the first-generation units were incorporated into the designs of two improved 50-m{sup 2} mirror modules. The results of Sandia's evaluation show significant improvement in optical performance over the first-generation designs, especially in windy conditions. 22 refs., 29 figs.

This report describes the application of word processing, graphics and data base software to the task necessary for the exclusion of Building 823 from the secure technical area at Sandia National Laboratories. In particular, this report focuses on the development of the building floor plans layouts and the space/personnel data base which were used by management to plan and coordinate the project. Once the project is complete, these information systems will continue to be maintained by other personnel for administrative purposes. The software developed has potential applicability to other facilities where administrative monitoring or space assessment is required. 6 figs.

Personnel from Stockpile Evaluation Program Division I, 7261, have been testing Joint Test Assemblies (JTAs) at Meppen Range, Federal Republic of Germany (FRG) since 1984. JTA trajectories were obtained from cinetheodolite film. The MPS-36 radar at Meppen Range is required to track the aircraft before bomb release to verify the release parameters for range safety and for the bomb trajectory after release. This is a difficult task because of the low-level approach of the aircraft. Division 7261 personnel asked Tonopah Test Range Department 7170 to assist in solving radar tracking problems. We recommended a new closed-circuit television system with a zoom lens and a force-operated, two-axis joystick. This system provides the operator a means of overriding the automode of the radar and manually positioning the radar antenna in azimuth (AZ) and elevation (EL). The joystick operator keeps the target (aircraft or bomb) centered in the TV picture by applying the correct pressure to the joystick. At the same time, the radar console operator maintains automatic range tracking by assisting the range gate through ground clutter using the control level of the range gate, as a rate-aid control in automatic mode. During the period May 8-17, 1989, the visual tracking equipment was installed in the Meppen radar. On May 16, 1989 a bomb dummy unit, loft maneuver was tracked successfully. The video, with time of day, was recorded for posttest, quick-look data. In the ten years of planned testing, a twenty-fold cost savings would be achieved with incorporation of the visual tracking capability to the MPS-36 radar, rather than providing radar beacons on each JTA. 8 figs.

Sandia National Laboratories, as part of the Containment Integrity Programs under the sponsorship of the Nuclear Regulatory Commission (NRC), has developed analytical techniques for predicting the performance of light water reactor steel containment buildings subject to loads beyond the design basis. The analytical techniques are based on experience with large-scale steel containment model tests that provided important insights and experimental validation of the analytical methods. As a means of demonstrating these analytical techniques, the NRC asked Sandia to conduct a structural evaluation of an actual steel containment building. The objective of the analysis was to determine the actual pressure capacity and the mode, location, and size of failure, where a functional definition of failure is used. The purpose of this report is to document the calculations performed to determine the pressure limits for the shell- rupture mode of failure. General failure of the containment shell is predicted by application of a failure criterion to the results from finite element structural analyses. The failure criterion relates the calculated values of strain in the containment plates, due to internal-pressurization loading, to the ultimate strain limit of the steel. Included in the failure criterion are adjustments for factors inherent in finite element analysis, such as level of detail and element size of the finite element model and variations in material property data. Separate finite element models were used to evaluate the overall free-field behavior of the structure and the localized behavior at a specific penetration location. 18 refs., 68 figs., 10 tabs.

In an experiment conducted at Sandia National Laboratories, 1:6-scale model of a reinforced concrete light water reactor containment building was pressurized with nitrogen gas to more than three times its design pressure. The pressurization produced one large tear and several smaller tears in the steel liner plate that functioned as the primary pneumatic seal for the structure. The data collected from the overpressurization test have been used to evaluate and further refine methods of structural analysis that can be used to predict the performance of containment buildings under conditions produced by a severe accident. This report describes posttest finite element analyses of the 1:6-scale model tests and compares pretest predictions of the structural response to the experimental results. Strain and displacements calculated in axisymmetric finite element analyses of the 1:6-scale model are compared to strains and displacement measured in the experiment. Detailed analyses of the liner plate are also described in the report. The region of the liner surrounding the large tear was analyzed using two different two-dimensional finite elements model. The results from these analyzed indicate that the primary mechanisms that initiated the tear can be captured in a two- dimensional finite element model. Furthermore, the analyses show that studs used to anchor the liner to the concrete wall, played an important role in initiating the liner tear. Three-dimensional finite element analyses of liner plates loaded by studs are also presented. Results from the three-dimensional analyses are compared to results from two-dimensional analyses of the same problems. 12 refs., 56 figs., 1 tab.

The Yucca Mountain Project (YMP) is examining the feasibility of siting a repository for high-level nuclear waste at Yucca Mountain, on and adjacent to the Nevada Test Site (NTS). The proposed repository will be excavated in the Topopah Spring Member, which is a moderately fractured, unsaturated, welded tuff. Excavation stability will be required during construction, waste emplacement, retrieval (if required), and closure to ensure worker safety. The subsurface excavations will be subject to stress changes resulting from thermal expansion of the rock mass and seismic events associated with regional tectonic activity and underground nuclear explosions (UNEs). Analyses of drift stability are required to assess the acceptable waste emplacement density, to design the drift shapes and ground support systems, and to establish schedules and cost of construction. This paper outlines the proposed methodology to assess drift stability and then focuses on an example of its application to the YMP repository drifts based on preliminary site data. Because site characterization activities have not begun, the database currently lacks the extensive site-specific field and laboratory data needed to form conclusions as to the final ground support requirements. This drift design methodology will be applied and refined as more site-specific data are generated and as analytical techniques and methodologies are verified during the site characterization process.

This Test Plan describes laboratory and modeling studies of: the chemistry of brines that could enter Waste Isolation Pilot Plant (WIPP) disposal rooms; the effects of anoxic corrosion of metals in steel containers and the waste on the gas and H{sub 2}O budgets of the repository; the effects of microbial activity, especially microbial degradation of cellulosics in the waste, on the gas and H{sub 2}O budgets of the repository, the Eh and pH of any brine present, and the chemical behavior of radionuclides; the effects of radiolysis on the gas and H{sub 2}O budgets of the repository; the efficacy of backfill additives proposed to remove microbially produced CO{sub 2} or prevent the formation of H{sub 2} from anoxic corrosion, and their effects on repository chemistry; the chemical behavior of Pu, Am, Th, and U in WIPP brines; additional development of the EQ3/6 geochemical software package for use in predicting the behavior of silicates and radionuclides in brines. This Test Plan describes studies of the chemical behavior of the repository as currently designed, and the chemical behavior of radionuclides under these conditions. Addenda will discuss additional studies relevant to design modifications, especially reprocessed waste, and chemically hazardous waste constituents. 165 refs., 7 tabs.

Generally multicomponent mixtures can exhibit a rich collection of phenomena. Thus it is to be expected that they will be described by complicated theories. In this paper we describe a relatively simple theory that is still theoretically correct, and discuss some of the phenomena that it exhibits. 12 refs.

Guest-host poled polymer films have become an active area of research as potential candidates for second-order nonlinear optical and electro-optic devices. This interest derives mainly from their large nonlinear optical coefficients, ease of fabrication, and high optical quality. Progress has been rapid in producing stable, efficient materials, and in building demonstration devices. The second-order nonlinear optical properties arise from the orientational order induced in a collection of highly nonlinear molecules incorporated in a glassy polymer matrix. After reviewing the alignment physics, we present results of nonlinear optical measurements on a methacrylate polymer functionalized with a dicyanovinyl terminated azo dye. Device issues concerning nonlinear optical devices are described with particular attention to phase-matching. We present data on the demonstration of anomalous-dispersion phase matched second harmonic generation in dye solutions. We also present results on electro-optic modulators. © 1989 SPIE.

The author describes a waveform-recorder evaluation system which is controlled by a Microvax II with instrumentation control through the IEEE-488 bus. Evaluation procedures are described with attention to the 'pathological cases' that can lead to significant misestimates of a digitizer's performance. The aim of these evaluation procedures is consistency with the new Trial Waveform Digitizer Standard generated by the Waveform Measurements and Analysis Committee appointed by the Instrumentation and Measurement Society of the IEEE. Methods are discussed for measuring the effective-bits performance of a waveform digitizer and determining differential nonlinearity.

The Primary Standards Laboratory at Sandia National Laboratories (SNL) and the Precision Engineering Division at the National Institute of Standards and Technology (NIST) are in the process of implementing software error correction on two nearly identical high-accuracy coordinate measuring machines (CMMs). Both machines are Moore Special Tool Company M-48 CMMs which are fitted with laser positioning transducers. Although both machines were manufactured to high tolerance levels, the overall volumetric accuracy was insufficient for calibrating standards to the levels both laboratories require. The error mapping procedure was developed at NIST in the mid 1970's on an earlier but similar model. The error mapping procedure was originally very complicated and did not make any assumptions about the rigidness of the machine as it moved, each of the possible error motions was measured at each point of the error map independently. A simpler mapping procedure was developed during the early 1980's which assumed rigid body motion of the machine. This method has been used to calibrate lower accuracy machines with a high degree of success and similar software correction schemes have been implemented by many CMM manufacturers. The rigid body model has not yet been used on highly repeatable CMMs such as the M48. In this report we present early mapping data for the two M48 CMMs. The SNL CMM was manufactured in 1985 and has been in service for approximately four years, whereas the NIST CMM was delivered in early 1989. 4 refs., 5 figs.

Merlin is a memory based, interconnection system designed to provide very high-performance capability in a disturbed multicomputer environment. By using dynamically mapped reflective memory operations, the system creates a virtual memory environment which permits users to utilize both local and shared memory techniques. This mapped virtual memory approach permits selected information to be shared at high speeds and with relatively low latency. There is no software involvement in the actual sharing of information and the system automatically overlaps computation and communication, to the extent possible, on a word-by-word basis. Memory-to-Memory mapping allows Merlin to provide a uniform programming environment which is independent of interconnection topology, processing elements, and languages. 14 refs., 4 figs.

In the most transmissive parts of the Culebra Dolomite, fluid flow is controlled by fractures. Gypsum (CaSO{sub 4} 2H{sub 2}O) and corrensite (a mixed chlorite/smectite) are the most abundant fracture-fill minerals. Radionuclide/clay interactions may be the dominant mechanism for radionuclide retardation. For this reason, the focus of this study is to examine the extent of the sorption of uranium and plutonium onto clays within the Culebra matrix and fractures. This paper describes several coordinated activities which will evaluate the potential retardation of radionuclide migration by sorption onto clays within the Culebras. These include characterization of the compositions of clays and groundwaters along the flow path; studies of the surface properties of simple reference clays and Culebra clays in dilute solutions and saline mixed electrolytes; development of a database of intrinsic equilibrium constants and specific-interaction parameters for calculations of the aqueous speciation of uranium and plutonium in Na-Cl-Ca-SO{sub 4}-CO{sub 3}-EDTA solutions which range in ionic strength from 0.1--4.0 molal; and measurement of surface complexation constants for uranium and plutonium in simple and mixed electrolyte solutions containing clays. 2 refs., 2 figs.

The nickel/hydrogen battery was developed in the early nineteen-seventies as an energy storage subsystem for commercial communication satellites. The advantages offered by nickel/hydrogen batteries, including long life, low maintenance and high reliability, make it very attractive for terrestrial applications such as stand-alone photovoltaic systems. The major drawback to the wider use of the nickel/hydrogen battery is its high initial cost. Sandia National Laboratories has placed cost-shared contracts with Comsat Laboratories and Johnson Controls, Inc., to reduce the cost, and a battery consisting of prismatic cells in a common pressure vessel has evolved. A 7-kWh battery has been on test at Sandia since January 1988 using a flat-plate photovoltaic array for charging. © 1990 IEEE

In component reliability assessment programs, three major sources of data are available for reliability assessment: a development program, production data, and field test data. In practice, reliability assessments are required at the end of each stages, and a common method of assessment is to simply combine the test data and provide a pooled estimate. The method suggested in this paper is Bayesian in that the uncertainty about the unreliability is expressed by means of a prior distribution with a specified upper limit. The method is hierarchical Bayes in that the uncertainty about the limit of that prior distribution is also expressed by means of a prior distribution. The data from the development program are incorporated with the prior on the unreliability and with the prior on the upper limit of the prior to obtain a new prior on unreliability. The production data are then used to obtain a revised estimate of the unreliability as well as a modified value for the limit of the prior distribution. This same concept will be carried through when the field data are obtained. The result is a final Bayesian reliability assessment that is iterative in nature and incorporates in a sequential fashion data from each of the three stages common to a component development, production, and surveillance program. 4 refs., 2 tabs.

Power loadings experienced by tokamak plasma-facing components during normal operation and during off-normal events are discussed. A model for power and particle flow in the tokamak boundary layer is presented and model predictions are compared to infrared measurements of component heating. The inclusion of the full three-dimensional geometry of the component and of the magnetic flux surface is very important in the modeling. Experimental measurements show that misalignment of component armour tile surfaces by only a millimeter can lead to significant localized heating. An application to the design of plasma-facing components for future machines is presented. Finally, thermal loads expected during tokamak disruptions are discussed. The primary problems are surface melting and vaporization due to localized intense heating during the disruption thermal quench and volumetric heating of the component armour and structure due to localized impact of runaway electrons. © 1990.

The tungsten subfluoride mechanism as well as other proposed mechanisms of selectivity loss are reviewed. To further demonstrate the viability of the tungsten subfluoride mechanism, we have extended the measurement of the tungsten subfluoride production rate down to 450{degree}C. We also report results from some preliminary experiments designed to identify the selectivity loss mechanism when elemental silicon is available for reaction. Comments regarding the origins of the insulator effect and selectivity loss for silane reduction are offered. 23 refs., 2 figs.

The use of NUREG-1150 and similar Probabilistic Risk Assessments in NRC and industry risk management programs is discussed. Risk management'' is more comprehensive than the commonly used term accident management.'' Accident management includes strategies to prevent vessel breach, mitigate radionuclide releases from the reactor coolant system, and mitigate radionuclide releases to the environment. Risk management also addresses prevention of accident initiators, prevention of core damage, and implementation of effective emergency response procedures. The methods and results produced in NUREG-1150 provide a framework within which current risk management strategies can be evaluated, and future risk management programs can be developed and assessed. Examples of the use of the NUREG-1150 framework for identifying and evaluating risk management options are presented. All phases of risk management are discussed, with particular attention given to the early phases of accidents. Plans and methods for evaluating accident management strategies that have been identified in the NRC accident management program are discussed. 2 refs., 3 figs.

A new interfacial force microscope capable of measuring the forces between two surfaces over the entire range of surface separations, up to contact, has been developed. The design is centered around a differential capacitance displacement sensor where the common capacitor plate is supported by torsion bars. A force-feedback control system balances the interfacial forces at the sensor, maintaining the common capacitor plate at its rest position. This control eliminates the instability which occurs with the conventional cantilever-based force sensors when the attractive force gradient exceeds the mechanical stiffness of the cantilever. The ability to measure interfacial forces at surface separations smaller than this instability point using the feedback control is demonstrated. 11 refs., 3 figs.

The lowest excited electronic state of molecular oxygen, singlet oxygen ({sup 1}{Delta}{sub g}0{sub 2}), can be produced in solid organic polymers by a variety of different methods. Once produced, singlet oxygen will return to the ground triplet state by two pathways, radiative (phosphorescence) and non-radiative decay. Although the quantum efficiency of phosphorescence is small ({minus}10{sup {minus}5}), singlet oxygen can be detected by its emission at 1270 mn in both steady-state and time-resolved experiments. The phosphorescence of singlet oxygen can be used to characterize many properties of a solid organic polymer. 2 refs., 5 figs.

We review our work on multi component polymeric nonlinear optical materials. These materials consist of nonlinear optical molecules incorporated in a polymeric host. A cross-linked triazine polymer incorporating a dicyanovinyl terminated azo dye was found to be relatively stable at 85{degree} and posses an electro-optic coefficient of 11pm/V. We have also observed the zero dispersion condition in a new anomalous dispersion dye for phase matched second harmonic generation, and expect efficient conversion to the blue. A squarylium dye, ISQ, has been found to posses a large third order nonlinearity, and may display two-level behavior. 24 refs., 11 figs.

ULSI manufacturing technologies have resulted in the development of Ultra-Pure Processing (UPP) capabilities for the world-wide semiconductor industry. The primary goal of Ultra Pure Processing is the elimination of extraneous contaminants, both gaseous and particulate, from the wafer process environment. This calls for a comprehensive approach to the design, operation, and maintenance of semiconductor process equipment. Through UPP one may reduce the number of uncontrolled variables within a system enhancing implementation of Statistical Process Control on the process environment within the tool (in situ). Greater control over the process environment translates into increased product quality, manufacturability, throughput and yield. Instituting UPP requires the capability of monitoring contaminants in the process environment a well as a systematic approach to isolating and eliminating contamination sources. Ultra Pure Processing can result from a Contamination Reduction Program. Presented here are the results from a Contamination Reduction Program performed on a state-of-the-art vertical thermal process reactor (VTR). 8 figs., 5 tabs.

Most previous Probabilistic Risk Assessments have excluded consideration of accidents initiated in low power and shutdown modes of operation. A study of the risk associated with operation in low power and shutdown is being performed at Sandia National Laboratories for a US Boiling Water Reactor (BWR). This paper describes the proposed methodology for the analysis of the risk associated with the operation of a BWR during low power and shutdown modes and presents preliminary information resulting from the application of the methodology. 2 refs., 2 tabs.

In this paper we formulate a speech coding system that incorporates trellis coded vector quantization (TCVQ) and adaptive predictive coding (APC). A method for optimizing'' the TCVQ codebooks is presented and experimental results concerning survivor path mergings are reported. Simulation results are given for encoding rates of 16 and 9.6 kbps for a variety of coder parameters. The quality of the encoded speech is deemed excellent at an encoding rate of 16 kbps and very good at 9.6 kbps. 13 refs., 2 figs., 4 tabs.

The Institute of Certified Records Managers (ICRM) is a non-profit, certifying organization of professional records managers and administrators. ICRM members are experienced in information requirements, records and information systems, and the related office systems and technologies. All members have met certification requirements and have received the Certified Records Manager (CRM) designation. As the field of information and records management moves toward standardization, and as the application of new technologies and technicalities complicate the measurement and demonstration of professional competence, the need for a means of identifying persons who have basic competency increases. The ICRM is providing such a means by testing and certifying basic knowledge. More and more job announcements are requiring this evidence of competency. Unfortunately, as an organization, NIRMA has a relatively small number of CRMs. The goal of the ICRM Development Group is two-fold; (1) to encourage NIRMA members to obtain their certification by providing basic information and support and; (2) to develop the Nuclear Specialist test module which will demonstrate that bearers have demonstrated expertise in nuclear records management as well as basic competencies. This report covers the examination process.

The Nuclear Information and Records Management Association (NIRMA) Task Force on Requirements Identification is currently involved in a four part project. During the course of the next year the Task Force will: (1) identify the generic requirements documents which have common applicability to nuclear utilities and DOE organizations; (2) research the requirements documents to identify individual requirements; (3) develop and implement a PC based tracking system to present and maintain the research data; and (4) implement a process for ongoing review of requirements. This report discusses these issues.

Multiplexer and amplifier systems must be designed with transistors that can perform satisfactorily over ten years to a total gamma dose of 120E6 rads and a total neutron fluence of 1.6E15 nvt for the SP-100 reactor system. Series of gamma and neutron tests have been completed to measure transistor degradation as a function of total dose, fluence, and temperature. Test results indicate that modest increases in temperature result in substantial improvement of transistor performance at a neutron flux of 8E8 n/cm{sup 2}/s. 2 refs., 3 figs.

Critical Heat Flux (CHF), also called burnout, is one of the major design limits for water-cooled divertors in tokamaks. Another important design issue is the correct thermal modeling of the divertor plate geometry where heat is applied to only one side of the plate and highly subcooled flow boiling in internal passages is used for heat removal. This paper discusses analytical techniques developed to address these design issues, and the experimental evidence gathered in support of the approach. Typical water-cooled divertor designs for the International Thermonuclear Experimental Reactor (ITER) are analyzed, and design margins estimated. Peaking of the heat flux at the tube-water boundary is shown to be an important issue, and design concerns which could lead to imposing large design safety margins are identified. The use of flow enhancement techniques such as internal twisted tapes and fins are discussed, and some estimates of the gains in the design margin are presented. Finally, unresolved issues and concerns regarding hydraulic design of divertors are summarized, and some experiments which could help the ITER final design process identified. 23 refs., 10 figs.

Our previous calorimetric studies of weld melting efficiency and arc efficiency in the GTAW and PAW processes have naturally led us to speculate as to the magnitude of the efficiencies in the LBW process which to data have also not been adequately investigated. Most welding engineers that have had experience with the LBW process are acutely aware that the metals' absorptivity, the surface finish, and the laser wavelength, all play an important role in affecting the energy transfer efficiency, but the extent of their influence and our understanding of the influence of other process variables is not well understood. In addition, it is widely thought that only the LBW or EBW processes can be selected for applications where thermal damage and distortion from the welding process must be kept to a minimum. For these reasons, we have looked forward to performing these calorimetric experiments since they potentially can answer such important questions as: whether or not the melting efficiency of the LBW process is superior to that obtainable with conventional GTAW and PAW welding processes This study was prompted by poor production yields on switching device due to cracking of the ceramic header after final closure welding with the CO{sub 2} LBW process. This calorimetric study was begun in hopes of determining if allowed variations in production process control variables were responsible for increases in heat input and the resulting thermal stresses. By measuring the net heat input to the workpiece with the calorimeter and by measuring the laser output energy and the weld fusion zone size it was possible to determine the magnitudes of both the energy transfer efficiency and the melting efficiency as well as observe their dependence on the process variables. 3 refs.

Component test plans are often designed by allocating a system's reliability goal among the system's components, then designing individual component test plans suitable for demonstrating achievement of each component's reliability goal. One use of the resulting component test data is the calculation of estimated system reliability, based on a model linking the component reliabilities to system reliability. The statistical precision of this system estimate depends on the component test plans (numbers of each component tested and the type of tests, e.g., variables or attributes) and, hence, is determined by the component test planners. Because system reliability may be of considerable interest, we feel an integrated view of component testing is required to assure that the ensemble of component tests will provide an adequate system reliability estimate. This paper considers the case of a series system of different components and binomial component data. For the case of equal numbers of units tested of each component (which can be shown to minimize total cost, subject to the risk constraints) the O.C. envelope is readily derived and from this envelope component test plans that satisfy the specified risks can be derived from equations that involve the cumulative binomial distribution function. Existing tables pertaining to acceptance sampling plans based on the binomial distribution can be used to determine the required number of component tests. 10 refs., 2 figs.

Weak formulations in Analytical Dynamics are developed, paralleling the variational methods in elastostatics, and including a fundamental yet novel approach for treating constraints (both holonomic and nonholonomic). A general three field approach is presented, in which the momentum balance conditions, the compatibility conditions between displacement and velocity, the constitutive relations and the displacement and momentum boundary conditions are all enforced in weak form. A primal, or kinematic formulation is developed from the general form by enforcing the compatibility conditions and displacement boundary conditions a priori. The conditional stability of the kinematic formulation is the counterpart of the locking phenomenon in elastostatics and may be avoided, either by reduced order integration, or by utilizing a mixed formulation. Toward this end, a two field mixed formulation is presented, which follows from the general form, when the constitutive relations are satisfied a priori. A general set of the constraint equations are introduced into the kinematic and mixed formulations, using a specific choice of multipliers, which results in modified variational principles. Several simple examples concerning rigid body dynamics are presented. 15 refs., 18 figs.

This paper describes arc discharge tests conducted in a prepressurized, constant-volume pressure vessel to study arc behavior over a wide range of current densities, discharge durations and initial vessel pressures. This method allows controlled access to a wider range of conditions than those previously studied in capillary tests. We have investigated aspects of the radiative heat transfer by calculating the material opacity and mean free paths of photons for conditions typical of arc diagnostics. We also performed one-dimensional Eulerian hydrodynamic calculations of the boundary layer behavior in the radiative diffusion approximation. These calculations, which describe the radial mass flow and heat transfer in the absence of turbulent flow effects, show the characteristic times for equilibrium of the high-pressure arc. Finally, we describe progress on a promising means for increasing the mass flux from the capillary discharge through the use of chemically reactive media on the capillary walls. 20 refs., 7 figs.

Integrated circuit logic states are maintained by virtue of specific transistor combinations being either on'' (conducting) or off'' (nonconducting). High energy ion strikes on the microcircuit generate photocurrents whose primary detrimental effect is to make off'' transistors appear on,'' confusing the logic state and leading to single event upset (SEU). Protection against these soft errors is accomplished using either technology or circuit techniques, actions that generally impact yield and performance relative to unhardened circuits. We describe, and using circuit simulations analyze, a technique for hardening latches which requires combinations of technology and circuit modifications, but which provides SEU immunity without loss of speed. Specifically, a single logic state is hardened against SEU using technology methods and the information concerning valid states is then used to simplify hardened circuit design. The technique emphasizes some basic hardening concepts, ideas for which will be reviewed. 3 refs., 2 figs.

Fabrication of high-efficiency silicon solar cells requires processing technology capable of maintaining long bulk carrier lifetime and low surface recombination. Development of long-lifetime processing techniques using experimental designs based on statistical methods is described. The first three experiments investigated pre-oxidation cleans, phosphorus gettering, and a comparison of different phosphorus diffusion sources. Optimal processing parameters were found to depend on type of silicon material. 2 refs., 2 figs., 2 tabs.

Thin film ferroelectric materials are the basis for a new, promising IC nonvolatile memory technology. The primary material being studied for ferroelectric memories is PZT. One of the key factors in determining the feasibility of PZT ferroelectric memories for weapon or space applications is whether PZT ferroelectric technology can be integrated into a radiation-hardened CMOS or bipolar process. Sandia National Laboratories has a program to study ferroelectric/CMOS process integration issues. The primary goal of this program is to determine if radiation-hardened reliable ferroelectric/CMOS IC memories can be fabricated. This program includes both the fabrication and characterization of ferroelectric test capacitors. In this paper we will give a brief overview of the program, discuss techniques developed to characterize ferroelectric devices for retention and endurance, and give results on studies of fatigue and retention of capacitors.

A travelling wave Faraday effect fiber current sensor, consisting of a helical optical fiber coil immersed in a dielectric medium, has been demonstrated. Improved phase matching conditions have led to measured bandwidth enhancements of greater than a factor of four. Sensitive devices with multi-gigahertz bandwidths are possible using this technique. 7 refs., 3 figs.