Paramount to the modeling of unsaturated flow and transport through fractured porous media is a clear understanding of the processes controlling fracture-matrix interaction. As a first step toward such an understanding, two preliminary experiments have been performed to investigate the influence of matrix imbibition on water percolation through unsaturated fractures in the plane normal to the fracture. Test systems consisted of thin slabs of either tuff or an analog material cut by a single vertical fracture into which a constant fluid flux was introduced. Transient moisture content and solute concentration fields were imaged by means of x-ray absorption. Flow fields associated with the two different media were significantly different owing to differences in material properties relative to the imposed flux. Richards` equation was found to be a valid means of modeling the imbibition of water into the tuff matrix from a saturated fracture for the current experiment.
A set of detailed geostatistical simulations of porosity has been produced for a layered stratigraphic sequence of welded and nonwelded volcanic tuffs at Yucca Mountain, Nevada. The simulations are produced using a composite. model of spatial continuity and they are highly conditioned to abundant drill hole (core) information. A set of derivative simulations of saturated hydraulic conductivity has been produced, in the absence of conditioning data, using a cross-variable relationship developed from similar data elsewhere. The detailed simulations reproduce both the major stratigraphic units and finer scale layering indicated by the drill hole data. These simulations have been scaled up several order of magnitude to represent block-scale effective hydrologic properties suitable for use in numerical modeling of groundwater flow and transport. The upscaling process involves the reformulation of a previously reported method that iteratively adapts an initial arbitrary grid to ``homogenize`` the detailed hydraulic properties contained within the adjusted cell limits and to minimize the size of cell in highly heterogeneous regions. Although the computation of the block-effective property involves simple numerical averaging, the blocks over which these averages are computed are relatively homogeneous, which reduces the numerical difficulties involved in averaging non-additive properties, such as permeability. The entire process of simulation and upscaling is rapid and computationally efficient compared with alterative techniques. It is thus suitable for the Monte Carlo evaluation of the uncertainty in site characterization as it affects the results of groundwater flow and transport calculations.
Hydrologic properties have been measured on outcrop samples taken from a detailed, two-dimension grid covering a 1.4 km outcrop exposure of the 10-m thick non-welded-to-welded, shardy base microstratigraphic unit of the Tiva Canyon Member of the Miocene Paintbrush Tuff at Yucca Mountain, Nevada. These data allow quantification of spatial trends in rock matrix properties that exist in this important hydrologic unit. Geologic investigation, combined with statistical and geostatistical analyses of the numerical data, indicates that spatial variability of matrix properties is related to deterministic geologic processes that operated throughout the region. Linear vertical trends in hydrologic properties are strongly developed in the shardy base microstratigraphic unit, and they are more accurately modeled using the concept of a thickness-normalized stratigraphic elevation within the unit, rather than absolute elevation. Hydrologic properties appear to be correlated over distances of 0.25 to 0.3 of the unit thickness after removing the deterministic vertical trend. The use of stratigraphic elevation allows scaling of identified trends by unit thickness which may be of particular importance in a basal, topography-blanketing unit such as this one. Horizontal changes in hydrologic properties do not appear to form obvious trends within the limited lateral geographic extent of the ash-flow environment that was examined. Matrix properties appear to be correlated horizontally over distances between 100 and 400 m. The existence and quantitative description of these trends and patterns of vertical spatial continuity should increase confidence in models of hydrologic properties and groundwater flow in this area that may be constructed to support the design of a potential high-level nuclear waste repository at Yucca Mountain.
This paper presents a method of estimating the rock mass properties for the welded and nonwelded tuffs based on currently available information on intact rock and joint characteristics at the Yucca Mountain site. Variability of the expected ground conditions at the potential repository horizon (the TSw2 thermomechanical unit) and in the Calico Hills nonwelded tuffs is accommodated by defining five rock mass quality categories in each unit based upon assumed and observed distributions of the data.
A numerical approach for modeling unsaturated flow is developed for heterogeneous simulations of fractured tuff generated using a geostatistical method. Cross correlations of hydrologic properties and upscaling of moisture retention curves is discussed. The approach is demonstrated for a study of infiltration at Yucca Mountain.
The regulations that currently govern repositories for spent fuel and high-level waste require demonstrations that are sometimes described as impossible to make. To make them will require an understanding of the current and the future phenomena at repository sites; it will also require credible estimates of the probabilities that the phenomena will occur in the distant future. Experts in many fields{emdash}earth sciences, statistics, numerical modeling, and the law{emdash}have questioned whether any amount of data collection can allow modelers to meet these requirements with enough confidence to satisfy the regulators. In recent years some performance assessments have begun to shed light on this question because they use results of actual site investigations. Although these studies do not settle the question definitively, a review of a recent total-system assessment suggests that compliance may be possible to demonstrate. The review also suggests, however, that the demonstration can be only at the ``reasonable`` levels of assurance mentioned, but not defined, in the regulations.
Previous laboratory investigations of tuff have shown that porosity has a dominant, general effect on mechanical properties. As a result, it is very important for the interpretation of mechanical property data that porosity is measured on each sample tested. Porosity alone, however, does not address all of the issues important to mechanical behavior. Variability in size and distribution of pore space produces significantly different mechanical properties. A nondestructive technique for characterizing the internal structure of the sample prior to testing is being developed and the results are being analyzed. The information obtained from this technique can help in both qualitative and quantitative interpretation of test results.
In situ thermomechanical experiments are planned as part of the Yucca Mountain Site Characterization Project that require instruments to measure stress and displacement at temperatures that exceed the typical specifications of existing geotechnical instruments. A high degree of instrument reliability will also be required to satisfy the objectives of the experiments, therefore a study was undertaken to identify areas where improvement in instrument performance was required. A preliminary list of instruments required for the experiments was developed, based on existing test planning and analysis. Projected temperature requirements were compared to specifications of existing instruments to identify instrumentation development needs. Different instrument technologies, not currently employed in geotechnical instrumentation, were reviewed to identify potential improvements of existing designs for the high temperature environment. Technologies with strong potentials to improve instrument performance with relatively high reliability include graphite fiber composite materials, fiber optics, and video imagery.
As a follow-on to Sandia`s 1991 preliminary total-system performance assessment of the Yucca Mountain site, this paper presents results of some sensitivity analyses that were done using results from the 1991 study. Two conceptual models of unsaturated-zone flow and transport at Yucca Mountain were included in the study, including both aqueous and gaseous releases. The sensitivities are quite different for the two models. For the composite-porosity model, the results are most sensitive to groundwater percolation flux, gaseous transport time, container lifetime, and fuel-matrix-alteration rate. For the weeps model, the results are most sensitive to parameters used to characterize fracture flow (fracture aperture and fracture connectivity) and infiltration (percolation flux and weep-episode factor).
The event-tree method of scenario construction has been chosen for the Yucca Mountain performance assessment. Its applicability and suitability to the problem are discussed and compared with those of the Nuclear Regulatory Commission (NRC) method. The event-tree method is appropriate for an incompletely characterized site, where there must be an evolving understanding, over time, of the processes at work, for a site that may require analysis of details in specific context, and when the scenario functions to guide site characterization. Anticipating the eventual requirement for using the NRC method, we show that the event-tree method can be translated to the NRC format after final scenario screening.
Chemical vapor deposition (CVD) is a widely used method for depositing thin films of a variety of materials. Applications of CVD range from the fabrication of microelectronic devices to the deposition of protective coatings. New CVD processes are increasingly complex, with stringent requirements that make it more difficult to commercialize them in a timely fashion. However, a clear understanding of the fundamental science underlying a CVD process, as expressed through computer models, can substantially shorten the time required for reactor and process development. Research scientists at Sandia use a wide range of experimental and theoretical techniques for investigating the science of CVD. Experimental tools include optical probes for gas-phase and surface processes, a range of surface analytic techniques, molecular beam methods for gas/surface kinetics, flow visualization techniques and state-of-the-art crystal growth reactors. The theoretical strategy uses a structured approach to describe the coupled gas-phase and gas-surface chemistry, fluid dynamics, heat and mass transfer of a CVD process. The software used to describe chemical reaction mechanisms is easily adapted to codes that model a variety of reactor geometries. Carefully chosen experiments provide critical information on the chemical species, gas temperatures and flows that are necessary for model development and validation. This brochure provides basic information on Sandia`s capabilities in the physical and chemical sciences of CVD and related materials processing technologies. It contains a brief description of the major scientific and technical capabilities of the CVD staff and facilities, and a brief discussion of the approach that the staff uses to advance the scientific understanding of CVD processes.
This paper presents a brief summary of condition monitoring results from an NRC-sponsored test program on aging, condition monitoring, and accident testing of Class 1E cables. In addition, since the program has been completed and the final reports have been published, this paper presents a list of references, along with abstracts for each reference. This list can serve as a guide for finding references to any desired information on the test program in varying levels of detail. The major conclusions of the test program with regard to condition monitoring were as follows: (a) of the parameters tested, elongation at break had the best correlation with aging for the most cable types; (b) hardness and indenter modulus (performed using the cable indenter developed under Electric Power Research Institute (EPRI) sponsorship) measurements both increased with aging for some of the materials, especially the jacket materials, and the modulus measurements were significantly more sensitive to aging than the hardness measurements; (c) where indenter modulus was sensitive to aging, it was most sensitive in the later stages of aging, after the elongation had reached nearly 0%; (d) density generally increased with aging for most materials, but some changes were inconsistent; and (e) with only a few exceptions, tensile strength and a number of different electrical measurements did not correlate well with aging.
A fundamental concern in the design of the potential repository at Yucca Mountain. Nevada is the response of the host rock to the emplacement of heat-generating waste. The thermal perturbation of the rock mass has implications regarding the structural, hydrologic. and geochemical performance of the potential repository. The phenomenological coupling of many of these performance aspects makes repository thermal modeling a difficult task. For many of the more complex, coupled models, it is often necessary to reduce the geometry of the potential repository to a smeared heat-source approximation. Such simplifications have impacts on induced thermal profiles that in turn may influence other predicted responses through one- or two-way thermal couplings. The effect of waste employment layout on host-rock thermal was chosen as the primary emphasis of this study. Using a consistent set of modeling and input assumptions, far-field thermal response predictions made for discrete-source as well as plate source approximations of the repository geometry. Input values used in the simulations are consistent with a design-basis a real power density (APD) of 80 kW/acre as would be achieved assuming a 2010 emplacement start date, a levelized receipt schedule, and a limitation on available area as published in previous design studies. It was found that edge effects resulting from general repository layout have a significant influence on the shapes and extents of isothermal profiles, and should be accounted for in far-field modeling efforts.
Calculations of residual stresses in braze joints are required to validate designs for a variety of metal/ceramic joining applications. In particular, finite element analysis (FEA) codes have the capability of incorporating either elastic-plastic or minimum creep rate constitutive models for the braze material. This paper presents both elevated temperature mechanical properties correlations for the eutectic Ag-Cu alloy, along with FEA results which use this data in calculating residual stresses in a generic metal/ceramic ``shear'' type braze joint. Three constitutive relations have been developed for eutectic Ag-Cu alloy: (i) an elastic/plastic correlation incorporating temperature-dependent yield stress and work hardening data, (ii) a high temperature minimum creep rate correlation with a temperature-dependent stress exponent and (iii) a minimum creep rate correlation using the Garofalo hyperbolic sine (sinh) equation. FEA calculations are presented for a eutectic Ag-Cu braze joint between metallized alumina ceramic and either Fe-29Ni-17Co or Fe-27Ni-25Co alloys using the three different constitutive relations for the brazement. The two creep correlations, since they are time-dependent, permit a study of the effect of various cooldown cycles on the maximum residual stress in the alumina ceramic. For the cooldown profiles studied in this paper, lower residual stresses are predicted in the ceramic-relative to the elastic-plastic model - when either of the two creep models are used as the constitutive law for the eutectic Ag-Cu braze joint. A second important result is that the simulations which incorporate the Fe-29-Ni-17Co alloy show higher peak stresses than the Fe-27Ni-25Co alloy at 420°C, along with much lower peak stresses compared to Fe-27Ni-25Co alloy at room temperature. The reason for this somewhat surprising behavior can be understood in terms of the coefficient of thermal expansion for the two Fe-Ni-Co alloys.
A description of ion-irradiation-induced reduction in the photoluminescence (PL) signal from porous silicon is given and a simple model which is consistent with a nanocrystalline Si structure is presented. Ion irradiation with 250 keV Ne is used to controllably reduce the integrated PL signal by 20% after a fluence of 4*1012 Ne cm-2 and completely eliminate the PL signal after a fluence of 4*1013 Ne cm-2. The use of vacuum and air annealing to recover ion-induced damage is also described, but the high temperatures for annealing cause elimination of the PL signal.
Proceedings, Annual Technical Meeting - Institute of Environmental Sciences
Benham, R.A.; Duggins, B.D.
Pyro shock loads are generated in many missile or rocket systems when stages are separated or shrouds are removed. These shocks are localized, of short rise time (10's of ns) and of very high stress level. This paper will document some anomalous behavior that occurs when pyro shock accelerometers (Endevco 7270A) are exposed to levels of high frequency shock that is higher than the manufacturer's recommended limits. Such shocks occur in many pyro shock events. Standard, accepted recording techniques can produce totally erroneous data with no obvious indicator that the data is in error. Wide band data recording, along with Fourier Analysis of the data, and dynamic analysis, made by the gage manufacturer of the transducer, allow recognition of some of the non-standard response modes excited but no method of quantifying the corrupted data has been developed. Wide band recording, which will preserve the data in the gage resonance range and above, are required to insure understanding of these pyro shock events.
We have measured the efficiency (tracks per incident neutron) of pure CR-39 for detecting DD and DT neutrons. Neutrons having average energies of 2.9 MeV (DD) and 14.8 MeV (DT) were produced by a 200-keV electrostatic accelerator and the neutron yields were measured using the associated particle counting technique. All CR-39 samples irradiated by DD or DT neutrons were etched for 2 h in a 70°, 6.25-N- NaOH bath. For bare CR-39, the efficiencies for detecting 2.9- and 14.8-MeV neutrons were found to be (1.3±0.4)×10 -4 and (5.0±1.8)×10-5, respectively. We also investigated using CR-39 and polyimide as proton radiators. For detecting 2.9-MeV neutrons, the radiators had no significant effect on efficiency; but for detecting 14.8-MeV neutrons the polyimide radiator increased the efficiency to (7.8±2.8)×10-5.
Progress in Z-pinch experiments at Sandia's Saturn facility have underscored a need for an absolute yield measurement for DD fusion neutrons. The technique chosen for making this absolute yield measurement was neutron activation of indium metal samples. To calibrate the technique, a 175-keV deuteron beam was allowed to impinge on a 3.0-μm-thick erbium deuteride target, producing neutrons through the 2H(d,n)3He fusion reaction. The neutron flux produced at 0° and incident on nominal 5-g indium samples was determined by the associated particle method. This method employed protons measured from the 2H(d,p)3H reaction to infer the neutron flux produced. After neutron irradiation, the activity of the indium samples was measured with a Ge gamma-ray detector. The total activity of the metastable state 115mIn (336.23 keV) was measured, compared with the total incident flux, and a calibration factor (indium counts/neutron/gram of indium) determined. For completeness, a calibration factor for DT neutrons from the 3H(d,n)4He fusion reaction was also obtained through the measured activity of the metastable state 114mIn(190.29 keV). The experiment and the measured calibration factors for both reactions are described in the paper.
The CR-39/range-filter technique measures ion energy by determining the maximum filter thickness which ions can penetrate. CR-39 located behind the filter records the ions. This method is used to measure peak voltage in pulsed power accelerators. We investigated range and straggling effects in this diagnostic by exposing it to 8- and 15-MeV protons for both Al and Ta filters. The range agreed with published values to better than ±6%. The range straggling decreased for higher incident ion energy and lower atomic number, as expected, although there were differences up to a factor of 1.7 between the experimental values and predictions. The dependence of the track diameter distribution on ion energy enabled us to establish a signature which is characteristic of ions which penetrate a filter, via straggling. These results can be used to evaluate the errors present when this diagnostic is used to measure accelerator voltage.
In recent proton beam experiments on PBFA-II, foam-filled gold targets and gas-filled spherical exploding pushers were shot as physics targets. Surrounding these targets were gold foils used to characterize the beam. The target fabrication and characterization are presented in this paper.
Because a direct measurement of the voltage (V) in pulsed power bremsstrahlung sources can be difficult, the energy spectrum of x rays emitted is sometimes used to infer V. Both the voltage and current in such sources vary with time. Moreover, for modern x-ray simulators with multiple cathodes, multiple voltages may exist simultaneously. We demonstrate here how such sources lead to systematic errors in several types of simple-to-field x-ray voltage measurements, especially those with broad spectral response functions, when calibrated against constant-potential bremsstrahlung spectra.
We have built a five-channel, x-ray detector array based on diamond photoconducting detectors (PCDs). The diamond elements have dimensions of 3 mm × 1 mm × 1 mm (or 0.5 mm). We use diamond PCDs for their stability, flat spectral response, and low leakage currents. The good time response of diamond PCDs is due to the 100-ps electron/hole recombination time. Filters were designed to give information in the 1-10-keV spectral region. Calibration of the diamond PCDs showed sensitivities between 4 and 7 × 10-4 A/W for a bias of 100 V. We shall present data from z-pinch experiments on Saturn.
Numerical simulations of perforation in steel plates involve the treatment of material failure during the perforation process. One way to model physical material separation is to delete failed elements from the analysis based on an appropriate failure criterion. Different algorithms were used in different transient finite element codes to delete failed elements. This investigation compares the results of PRONTO 2D and LS-DYNA2D codes for a specific steel plate perforation problem. Influences of the deletion algorithms on material parameters are discussed.
A framework for coupled elastoplastic and damage theories is developed, following a rigorous thermodynamic procedure. This framework is sufficiently general to include anisotropic plasticity and damage formulations. Both the plastic yield and damage functions are constructed using homogeneous functions of degree one. The principle of maximum dissipation or maximum entropy production is used to derive the evolution relations together with the loading and unloading conditions. In addition, the convexity of the undamaging elastic domain is shown. For plasticity the resulting evolution of the plastic strains corresponds to an associative flow. This general framework is shown to be sufficiently general to describe several popular theories for both plasticity and damage. Limitations of some existing damage theories are discussed.
Continuum damage theories describe the progressive reduction in stiffness and strength of brittle materials resulting from the initiation and growth of microcracks and microvoids. When brittle materials are loaded into the nonlinear regime, they often exhibit localized zones of intense deformation and the eventual formation of macrocracks. Criteria for diffuse and discontinuous bifurcations have previously been developed and used to study the initiation of necking and localization in elastic-plastic materials. In this investigation, the same bifurcation criteria are applied to continuum damage theories. Since the bifurcation criteria depend on the fourth-order tangent modulus tensor, the first step in this investigation is the derivation of the tangent modulus tensor for a general continuum damage theory. An eigenanalysis of the symmetric part of the tangent modulus tensor is then shown to fully characterize the potential diffuse and discontinuous bifurcations associated with a given continuum damage theory.
As part of the NRC-sponsored program to study the implications of Generic Issue 57, Effects of Fire Protection System Actuation on Safety-Related Equipment,'' a subtask was performed to evaluate the applicability of formal decision analysis methods to generic issues cost/benefit-type decisions and to apply these methods to the GI-57 results. In this report, the numerical results obtained from the analysis of three plants (two PWRs and one BWR) as developed in the technical resolution program for GI-57 were studied. For each plant, these results included a calculation of the person-REM averted due to various accident scenarios and various proposed modifications to mitigate the accident scenarios identified. These results were recomputed to break out the benefit in terms of contributions due to random event scenarios, fire event scenarios, and seismic event scenarios. Furthermore, the benefits associated with risk (in terms of person-REM) averted from earthquakes at three different seismic ground motion levels were separately considered. Given this data, formal decision methodologies involving decision trees, value functions, and utility functions were applied to this basic data. It is shown that the formal decision methodology can be applied at several different levels. Examples are given in which the decision between several retrofits is changed from that resulting from a simple cost/benefit-ratio criterion by virtue of the decision-makinger's expressed (and assumed) preferences.
Leonard, J.A.; Floyd, H.L.; Parrott, L.; Goetsch, B.; Doran, L.
This issue describes several innovative technologies in modern manufacturing. Methods in which the HIRCIS sensor may cut costs in precision machining are described. Computer models and experimental methods aid in the chemical vapor deposition of high-temperature coatings. Shared computer networks provide communication for interactive collaboration. Sol-gel processing of tailored thin films furnish low cost, high quality glass coatings at room temperature. Integrated circuit characterization tools and expertise are available to improve quality and reliability in the microelectronic industry.
This paper describes preliminary experiments to investigate electron-beam radiolysis of model compounds appropriate for crude oil spills on water or soil. Since no previous work in this area is known to exist, the rate of destruction of such concentrated organic materials in aqueous media is not known. The experiments conducted here were designed to provide preliminary estimates of the destruction rate and the estimated costs. Samples of model compounds were irradiated to dose levels up to 700 Mrad (H{sub 2}0) and the change in chemical composition was determined by mass spectrometry/gas chromatography and Fourier transform infrared spectroscopy. It was found that a dose of 700 Mrads reduced the liquid volume of the model compound by 60% and that the major effect of irradiation was the formation of long chain alkanes and dimethyl and ethyl benzenes. Under certain conditions a solid polymer was found to form. When alcohol was present in the model compound, additional products included small quantities of ethane diodic acid, butanol, butanediol, and various other alcohols. Further research is recommended to obtain a better analysis of the products, better values for the destruction rates, and better understanding of dose rate effects.
For nearly 10 years, the Gould Electronics, Incorporated manufacturing plant in Chandler, Arizona, has been a model of how medium-temperature solar thermal energy systems can produce economical industrial process heat (IPH). In 1982, a solar IPH system was designed and built on the site by Solar Kinetics, Inc. The system has remained in operation and continues to provide economical process heat for Gould`s copper foil manufacturing operation. System performance and availability has fluctuated over the years, reaching a low point in early 1990 when the system was nearly inoperative because of equipment reliability problems. Gould teamed with engineers from Sandia National Laboratories` (Sandia) Solar Thermal Design Assistance Center to develop a plan to solve the technical problems and refurbish the field. The IPH system is currently operating at over 90-percent equipment availability, returning to Gould a net energy cost savings on the order of $7,500 per month. This paper presents the history and operation of the system from the perspective of the end user and describes the phased upgrade program undertaken with Sandia to refurbish the system.
The Jet Propulsion Laboratory is developing a large space-truss to support a micro-precision interferometer. A finite element model will be used to design and place passive and active elements in the truss to suppress vibration. To improve the model`s predictive capability, it is desirable to identify uncertain structural parameters in the model by utilizing experimental modal data. Testing of both the components and the system was performed to obtain the data necessary to identify the structural parameters. Extracting a modal model, absent of bias errors, from measured data requires great care in test design and implementation. Testing procedures that are discussed include: verification of non-constraining shaker attachment, quantification of the non-linear structural response, and the design and effects of suspension systems used to simulate a free structure. In addition to these procedures, the accuracy of the measured frequency response functions are evaluated by comparing functions measured with random excitation, using various frequency resolutions, and with step sine excitation.
This publication presents information from Sandia laboratories concerning developments in the following areas: a miniaturized sensor system for the testing and analysis of hazardous wastes;a cross-well seismic receiver for petroleum deposit detection; and computer codes for designing dish-stirling sytems.
The design, calibration, and preliminary test results for an underwater shock gauge are presented. The active element is a 25-{mu}m thick polyvinylidene fluoride shock sensor providing rise times as short as 50 ns. Fast rise time is essential to accurate recording of shock pulses with durations of only a few microseconds. The piezoelectric polymer provides a self-generating pressure sensor requiring neither amplification nor additional active electronic circuitry. The gauge package is designed to minimize electromagnetic interference from the high-voltage fire set used to power the exploding bridge wire pressure source. The gauge package is constructed to withstand the initial water shock as well as subsequent reactions in the water that result in strong water motion and bubble generation. Thin-film diaphragm sensors are not sturdy enough to withstand this environment. Initial tests show that the gauge responds in 200 ns in water and that low-frequency response is sufficient to allow recording for at least 40 {mu}s after the initial shock arrival.
Performance and functionality increases in network environments have in the need for readily accessible mass storage. UNIX{reg_sign}-based networks and mass storage systems are providing the required connectivity and interoperability, however, how UNIX-based mass storage systems are being used is not well documented. This paper describes a study of the usage of the UNIX-based Network Storage Service at Sandia National Laboratories.
A discrete element computer program, DMC (Distinct-Motion Code), has been used for several years to simulate blasting-induced rock motion. Recent enhancements of DMC`s capabilities have included addition of an algorithm that couples together rock motion and gas flow. This allows the user to specify a particular explosive which also specifies equation-of-state and other parameters necessary to model explosive gas flow from the blastwell. Rock loading by the flowing gas is calculated automatically. The mechanism for calculating the rock loading is the subject of this paper. The rock motion effects the gas flow calculation by changing the porosity. DMC is currently being used on a SLTN SPARCstation 2 computer workstation.
Solder wettability of Class II environmentally exposed Cu substrates coated with an organic solderability preservative (OSP) is being investigated. The OSP coatings slightly retarded the wetting behavior of 60Sn-40Pb solder during baseline testing of unaged coupons. A nominal increase in wetting angle, or decrease in wettability, was observed on the inhibited surfaces, particularly when less active fluxes were used. Small increases in the wetting time and decreases in the wetting rate were also measured. Simulated accelerated aging tests are underway to determine the effects of aging in a typical indoor industrial environment on the solder wettability of OSP coated Cu.
Sandia operated by AT&T for the US Department of Energy. Sandia has a billion dollar annual budget and over 8,000 employees. Sandia`s main sites are in Albuquerque, New Mexico; Livermore, California; and Tonopah, Nevada. Sandia has a broad base of engineering and scientific skills that supports the whole product cycle from advanced R&D through manufacturing and end-user support. Sandia`s original mission was to develop the non-nuclear portion of nuclear weapons. In the 1970s, the mission was expanded to include technical work on conventional and alternative energy sources. Recently, the mission was further expanded to include technology transfer and US competitiveness. This report describes the activities in the Component Development and Engineering Support Division 2000 (indicated by the bold lines on the organization chart). Division 2000 develops electrical, electronic, optical, explosive, mechanical, and other components that are the core products of Sandia systems. The Division also develops advanced capabilities in CAD/CAE, test, nondestructive test, programming, reliability, failure analysis, and simulation that are part of the core services required by Sandia systems. For each of the core products and services described in this brochure, there is a corresponding set of science and engineering capabilities that are Sandia`s core competencies. Also, there are systems groups that use these core products and services to develop ultra-reliable systems for Sandia`s customers. Most of these groups have literature available describing their capabilities and expertise.
Nuclear power plants have experienced actuations of fire protection systems (FPSs) under conditions for which these systems were not intended to actuate. They have also experienced advertent actuations with the presence of a fire. These actuations have often damaged nearby plant equipment. A review of past occurrences of both types of such events on nuclear power plant safety has been performed. Thirteen different scenarios leading to actuation of fire protection systems due to a variety of causes were identified. These scenarios range from inadvertant actuation caused by human errors to hardware failures and include seismic root causes and seismic/fire interactions. A quantification of these thirteen scenarios, where applicable, was performed on a BWR4/MKI. This report estimates the contribution of FPS actuations to core damage frequency and to risk.
Data are presented from the Geomechanical Evaluation (first phase), a very large scale in situ test fielded underground at the Waste Isolation Pilot Plant (WIPP). These data include selected fielding information, test configuration, instrumentation activities, and comprehensive results from a large number of gages. Construction of the test began in December 1984 and the test has been in operation since that time; gage data in this report cover the period from December 1984 through November 1990.
Nuclear power plants have experienced actuations of fire protection systems (FPSs) under conditions for which these systems were not intended to actuate and also have experienced advertent actuations with the presence of a fire. These actuations have often damaged safety-related equipment. A review of the impact of past occurrences of both types of such events and their impact on plant safety systems, an analysis of the risk impacts of such events on nuclear power plant safety, and a cost-benefit analysis of potential corrective measures have been performed. Thirteen different scenarios leading to actuation of fire protection systems due to a variety of causes were identified. These scenarios ranged from inadvertent actuation caused by human error to hardware failure, and include seismic root causes and seismic/fire interactions. A quantification of these thirteen root causes, where applicable, was performed on generically applicable scenarios. This document, Volume 2, contains appendices A,B, and C of this report.
Nuclear power plants have experienced actuations of fire protection systems (FPSs) under conditions for which these systems were not intended to actuate and also have experienced advertent actuations with the presence of a fire. These actuations have often damaged nearby plant equipment. A review of the impact of past occurrences of both types of such events, a quantification of the risk of FPS actuation, a sensitivity study of the quantification of the risk of FPS actuation and risk calculations in terms of person-REM have been performed. Thirteen different scenarios leading to actuation of fire protection systems due to a variety of causes were identified. A quantification of these thirteen scenarios, where applicable, was performed on a 3-loop Westinghouse Pressurized water Reactor (PWR). These scenarios ranged from inadvertent actuation caused by human error to hardware failures, and include seismic root causes and seismic/fire interaction. This report estimates the contribution of FPS actuations to core damage frequency and risk.
The VICTORIA model of radionuclide behavior in the reactor coolant system (RCS) of a light water reactor during a severe accident is described. It has been developed by the USNRC to define the radionuclide phenomena and processes that must be considered in systems-level models used for integrated analyses of severe accident source terms. The VICTORIA code, based upon this model, predicts fission product release from the fuel, chemical reactions involving fission products, vapor and aerosol behavior, and fission product decay heating. Also included is a detailed description of how the model is implemented in VICTORIA, the numerical algorithms used, and the correlations and thermochemical data necessary for determining a solution. A description of the code structure, input and output, and a sample problem are provided.
Brine inflow to the Waste Isolation Pilot Plant is important in assessing the performance of the repository, and a mechanistic model is needed for performance calculations. Brine inflow experiments are being conducted, and formation parameters such as the permeability and diffusivity are inferred from these data using a simplified one-dimensional radial, uniform property, single-phase Darcy flow model. This model has met with limited success in interpreting some of the recent data. Much of the data could not be satisfactorily fit with the above model because the brine inflow rate increases with time, so a more mechanistic model is being developed based on the TOUGH and TOUGH2 computer codes. These codes are much more complex than the simplified model and include a number of parameters that have not been measured. Therefore, a one-dimensional brine inflow sensitivity study has been undertaken to evaluate the importance of a number of these parameters in influencing the behavior of brine inflow to open boreholes. In addition, two-phase conditions have been included in the study, and the sensitivity of gas inflow rates and the formation pressure and saturation distributions after 1 year are examined. These results should be helpful in determining what additional measurements are necessary to assist in the development of a more mechanistic brine inflow model.
The Precision Linear Shaped Charge (PLSC) design concept involves the independent fabrication and assembly of the liner (wedge of PLSC), the tamper/confinement, and explosive. The liner is the most important part of an LSC and should be fabricated by a more quality controlled, precise process than the tamper material. Also, this concept allows the liner material to be different from the tamper material. The explosive can be loaded between the liner and tamper as the last step in the assembly process rather than the first step as in conventional LSC designs. PLSC designs are shown to produce increased jet penetrations in given targets, more reproducible jet penetration, and more efficient explosive cross sections using a minimum amount of explosive. The Linear Explosive Shaped Charge Analysis (LESCA) code developed at SandiaNational Laboratories has been used to assist in the design of PLSCs. LESCA predictions for PLSC jet penetration in aluminum targets, jet tip velocities and jet-target impact angles are compared to measured data.