Publications

This report presents the results of three fire endurance tests and one ampacity derating test set of the fire barrier system Thermo-Lag 330-1 Subliming Coating. Each test was performed using cable tray specimens protected by a nominal three-hour fire barrier envelope comprised of two layers of nominal 1/2 inch thick material. The fire barrier systems for two of the three fire endurance test articles and for the ampacity derating test article were installed in accordance with the manufacturer`s installations procedures. The barrier system for the third fire endurance test article was a full reproduction of one of the original manufacturer`s qualification test articles. This final test article included certain installation enhancements not considered typical of current nuclear power plant installations. The primary criteria for fire endurance performance evaluation was based on cable circuit integrity testing. Secondary consideration was also given to the temperature rise limits set forth in the ASTM E119 standard fire barrier test procedure. All three of the fire endurance specimens failed prematurely. Circuit integrity failures for the two fire endurance test articles with procedures-based installations were recorded at approximately 76 and 59 minutes into the exposures for a 6 inch wide and 12 inch wide cable tray respectively. Temperature excursion failures (single point) for these two test articles were noted at approximately 65 and 56 minutes respectively. The first circuit integrity failure for the full reproduction test article was recorded approximately 119 minutes into the exposure, and the first temperature excursion failure for this test article was recorded approximately 110 minutes into the exposure.

An application protocol is an information systems engineering view of a specific product. The view represents an agreement on the generic activities needed to design and fabricate the product, the agreement on the information needed to support those activities, and the specific constructs of a product data standard for use in transfering some or all of the information required. This applications protocol describes the data for electrical and electronic products in terms of a product description standard called the Initial Graphics Exchange Specification (IGES). More specifically, the Layered Electrical Product IGES Application Protocol (AP) specifies the mechanisms for defining and exchanging computer-models and their associated data for those products which have been designed in two dimensional geometry so as to be produced as a series of layers in IGES format. The AP defines the appropriateness of the data items for describing the geometry of the various parts of a product (shape and location), the connectivity, and the processing and material characteristics. Excluded is the behavioral requirements which the product was intended to satisfy, except as those requirements have been recorded as design rules or product testing requirements.

Abstract not provided.

Remediation of waste from Underground Storage Tanks (UST) at Hanford will require the use of large remotely controlled equipment. Inherent safety methods need to be identified and incorporated into the retrieval system to prevent contact damage to the UST or to the remediation equipment. This report discusses the requirements for an adequate protection system and reviews the major technologies available for inclusion in a damage protection system. The report proposes that adequate reliability of a protection system can be achieved through the use of two fully-independent subsafety systems. Safety systems technologies reviewed were Force/Torque Sensors, Overload Protection Devices, Ultrasonic Sensors, Capacitance Sensors, Controller Software Limit Graphic Collision Detection, and End Point Tracking. A relative comparison between retrieval systems protection technologies is presented.

Horizontal drilling is a viable approach for accessing hydrocarbons in many types of naturally-fractured reservoirs. Cost-effective improvements in the technology to drill, complete, and produce horizontal wells in difficult geologic environments require a better understanding of the mechanical and fluid-flow behavior of these reservoirs with changes ineffective stress during their development and production history. In particular, improved understanding is needed for predicting borehole stability and reservoir response during pore pressure drawdown. To address these problems, a cooperative project between Oryx Energy Company and Sandia National Laboratories was undertaken to study the effects of rock properties, in situ stress, and changes in effective stress on the deformation and permeability of stress sensitive, naturally-fractured reservoirs. A low value for the proelastic parameter was found, implying that the reservoir should have a low sensitivity to declining pore pressure. A surprisingly diverse suite of fractures was identified from core. From the coring-induced fractures, it was plausible to conclude that the maximum principal stress was in the horizontal plane. Measurements on permeability of naturally fractured rock in a newly-developed experimental arrangement showed that slip on fractures is much more effective inchangingpcrtncability than is normal stress. The intermediate principal stress was found to have a strong effect, on the strength and ductility of the chalk, implying the need for a more sophisticated calculation of borehole stability.

Abstract not provided.

This study investigates the high frequency response of Faraday effect optical fiber current sensors that are bandwidth-limited by the transit time of the light in the fiber. Mathematical models were developed for several configurations of planar (collocated turns) and travelling wave (helical turns) singlemode fiber sensor coils, and experimental measurements verified the model predictions. High frequency operation above 500 MHz, with good sensitivity, was demonstrated for several current sensors; this frequency region was not previously considered accessible by fiber devices. Planar fiber coils in three configurations were investigated: circular cross section with the conductor centered coaxially; circular cross section with the conductor noncentered; and noncircular cross section with arbitrary location of the conductor. The helical travelling wave fiber coils were immersed in the dielectric of a coaxial transmission line to improve velocity phase matching between the field and light. Three liquids (propanol, methanol, and water) and air were used as transmission line dielectric. Complete models, which must account for liquid dispersion and waveguide dispersion from the multilayer dielectric in the transmission line, were developed to describe the Faraday response of the travelling wave sensors. Other travelling wave current sensors with potentially greater Faraday sensitivity, wider bandwidth and smaller size are investigated using the theoretical models developed for the singlemode fibers coils.

Abstract not provided.

The U.S. Department of Energy (DOE) is responsible for disposing of a variety of radioactive and mixed wastes, some of which are considered special-case waste because they do not currently have a clear disposal option. It may be possible to dispose of some of the DOE`s special-case waste using greater confinement disposal techniques at the Nevada Test Site (NTS). The DOE asked Sandia National Laboratories to investigate this possibility by performing system configuration analyses. The first step in performing system configuration analyses is to estimate the characteristics of special-case waste that might be destined for disposal at the NTS. The objective of this report is to characterize this special-case waste based upon information available in the literature. No waste was sampled and analyzed specifically for this report. The waste compositions given are not highly detailed, consisting of grains and curies of specific radionuclides per cubic meter. However, such vague waste characterization is adequate for the purposes of the system configuration task. In some previous work done on this subject, Kudera et al. [1990] identified nine categories of special-case radioactive waste and estimated volumes and activities for these categories. It would have been difficult to develop waste compositions based on the categories proposed by Kudera et al. [1990], so we created five groups of waste on which to base the waste compositions. These groups are (1) transuranic waste, (2) fission product waste, (3) activation product waste, (4) mobile/volatile waste, and (5) sealed sources. The radionuclides within a given group share common characteristics (e.g., alpha-emitters, heat generators), and we believe that these groups adequately represent the DOE`s special-case waste potentially destined for greater confinement disposal at the NTS.

The purpose of the Reactor Pressure vessel Thermal Annealing Workshop was to provide a forum for US utilities and interested parties to discuss relevant experience and issues and identify potential solutions/approaches related to: An understanding of the potential benefits of thermal annealing for US commercial reactors; on-going technical research activities; technical aspects of a generic, full-scale, in-place vessel annealing demonstration; and the impact of economic, regulatory, and technical issues on the application of thermalannealingtechnology to US plants. Experts from the international nuclear reactor community were brought together to discuss issues regarding application of thermal annealing technology in the US and identify the steps necessary to commercialize this technology for US reactors. These proceedings contain all presentation materials discussed during the Workshop. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

Abstract not provided.

This SAND report summarizes the work completed for a Novel Project Research and Development LDRD project. In this research effort, new mathematical techniques from the theory of nonlinear generalized functions were applied to compute solutions of nonlinear hyperbolic field equations in nonconservative form. Nonconservative field equations contain products of generalized functions which are not defined in classical mathematics. Because of these products, traditional computational schemes are very difficult to apply and can produce erroneous numerical results. In the present work, existing first-order computational schemes based on results from the theory of nonlinear generalized functions were applied to simulate numerically two model problems cast in nonconservative form. From the results of these computational experiments, a higher-order Godunov scheme based on the piecewise parabolic method was proposed and tested. The numerical results obtained for the model problems are encouraging and suggest that the theory of nonlinear generalized functions provides a powerful tool for studying the complicated behavior of nonlinear hyperbolic field equations.

Abstract not provided.

Abstract not provided.

In situ design verification activities are being conducted in the North Ramp Starter Tunnel of the Yucca Mountain Project Exploratory Studies Facility. These activities include: monitoring the construction blasting, evaluating the damage to the rock mass associated with construction, assessing the rock mass quality surrounding the tunnel, monitoring the performance of the installed ground support, and monitoring the stability of the tunnel. In this paper, examples of the data that have been collected and preliminary conclusions from the data are presented.

The authors consider the following problem that arises in assembly planning: given an assembly, identify a subassembly that can be removed as a rigid object without disturbing the rest of the assembly. This is the assembly partitioning problem. Specifically, they consider planar assemblies of simple polygons and subassembly removal paths consisting of a single finite translation followed by a translation to infinity. They show that such a subassembly and removal path can be determined in O(n{sup 1.46}N{sup 6}) time, where n is the number of polygons in the assembly and N is the total number of edges and vertices of all the parts together. They then extend this formulation to removal paths consisting of a small number of finite translations, followed by a translation to infinity. In this case the algorithm runs in time polynomial in the number of parts, but exponential in the number of translations a path may contain.

Magnetoluminescence determined conduction-band and valence-band dispersion curves are presented for n-type InGaAs/GaAs stained-single-quantum well structures. The magnetic field range was 0 to 30 tesla, and the temperature varied between 4.2 and 77.4 K.

Effects of frequency, temperature and hydrostatic pressure on dielectric properties, molecular relaxations, and phase transitions of PVDF and a copolymer with 30 mol % trifluoroethylene are discussed. Pressure causes large slowing down of the {beta} molecular relaxations as well as large increases in the, ferroelectric transition temperatures and melting points, but the magnitudes of the effects are different for the different transitions. These effects can be understood in terms of pressure-induced hindrance of the molecular motions and/or reorientations. A unique application of these polymers as time-resolved dynamic stress gauges based on PVDF studies under very high pressure shock compression is discussed.

Design improvements for the International Atomic Energy Agency`s Spent Fuel Attribute Tester, recommended on the basis of an optimization study, were incorporated into a new instrument fabricated under the Finnish Support Programme. The new instrument was tested at a spent fuel storage pool on September 8 and 9, 1993. The result of two of the measurements have been compared with calculations. In both cases the calculated and measured pulse height spectra in good agreement and the {sup 137}Cs gamma peak signature from the target spent fuel element is present.

NATO and former Warsaw Pact nations have agreed to allow overflights of their countries in the interest of easing world tension. The United States has decided to implement two C-135 aircraft with a Synthetic Aperture Radar (SAR) that has a 3-meter resolution. This work is being sponsored by the Defense Nuclear Agency (DNA) and will be operational in Fall 1995. Since the SAR equipment must be exportable to foreign nations, a 20-year-old UPD-8 analog SAR system was selected as the front-end and refurbished for this application by Loral Defense Systems. Data processing is being upgraded to a currently exportable digital design by Sandia National Laboratories. Amplitude and phase histories will be collected during these overflights and digitized on VHS cassettes. Ground stations will use reduction algorithms to process the data and convert it to magnitude-detected images for member nations. System Planning Corporation is presently developing a portable ground station for use on the demonstration flights. Aircraft integration into the C-135 aircraft is being done by the Air Force at Wright-Patterson AFB, Ohio.

We describe the design and fabrication of two types of solid state moisture sensors, and discuss the results of an evaluation of the sensors for the detection of trace levels of moisture in semiconductor process gases. The first sensor is based on surface acoustic wave (SAW) technology. A moisture sensitive layer is deposited onto a SAW device, and the amount of moisture adsorbed on the layer produces a proportional shift in the operating frequency of the device. Sensors based on this concept have excellent detection limits for moisture in inert gas (100 ppb) and corrosive gas (150 ppb in HCl). The second sensor is a simple capacitor structure that uses porous silicon as a moisture-sensitive dielectric material. The detection limits of these sensors for moisture in inert gas are about 700 ppb prior to HCl exposure, and about 7 ppm following HCl exposure.

Several basic reasons are given to support the position that an integrated, systems methodology entailing probabilistic assessment offers the best means for addressing the problems in software safety. The recognized hard problems in software safety, or safety per se, and some of the techniques for hazard identification and analysis are then discussed relative to their specific strengths and limitations. The paper notes that it is the combination of techniques that will lead to safer systems, and that more experience, examples, and applications of techniques are needed to understand the limits to which software safety can be assessed. Lastly, some on-going project work at Sandia National Laboratories on developing a solution methodology is presented

The Australian Safeguards Office (ASO) and the US Department of Energy (DOE) have sponsored work under a bilateral agreement to implement a Remote Monitoring System (RMS) at an Australian nuclear site operated by the Australian Nuclear Science and Technology Organization (ANSTO). The RMS, designed by Sandia National Laboratories (SNL), was installed in February 1994 at the Dry Spent Fuel Storage Facility (DSFSF) located at Lucas Heights, Australia. The RMS was designed to test a number of different concepts that would be useful for unattended remote monitoring activities. The DSFSF located in Building 27 is a very suitable test site for a RMS. The RMS uses a network of low cost nodes to collect data from a number of different sensors and security devices. Different sensors and detection devices have been installed to study how they can be used to complement each other for C/S applications. The data collected from the network will allow a comparison of how the various types of sensors perform under the same set of conditions. A video system using digital compression collects digital images and stores them on a hard drive and a digital optical disk. Data and images from the storage area are remotely monitored via telephone from Canberra, Australia and Albuquerque, NM, USA. These remote monitoring stations operated by ASO and SNL respectively, can retrieve data and images from the RMS computer at the DSFSF. The data and images are encrypted before transmission. The Remote Monitoring System field tests have been operational for six months with good test results. Sensors have performed well and the digital images have excellent resolution. The hardware and software have performed reliably without any major difficulties. This paper summarizes the highlights of the prototype system and the ongoing field tests.

An important aspect of insider protection in production facilities is the monitoring of the movement of special nuclear material (SNM) and personnel. One system developed at Sandia National Labs for this purpose is the Personnel and Material Tracking System (PAMTRAK). PAMTRAK can intelligently integrate different sensor technologies and the security requirements of a facility to provide a unique capability in monitoring and tracking SNM and personnel. Currently many sensor technologies are used to track the location of personnel and SNM inside a production facility. These technologies are generally intrusive; they require special badges be worn by personnel, special tags be connected to material, and special detection devices be mounted in the area. Video technology, however, is non-intrusive because it does not require that personnel wear special badges or that special tags be attached to SNM. Sandia has developed a video-based image processing system consisting of three major components: the Material Monitoring-Subsystem (MMS), the Personnel Tracking Subsystem (PTS) and the Item Recognition Subsystem (IRS). The basic function of the MMS is to detect movements of SNM, that occur in user-defined regions of interest (ROI) from multiple cameras; these ROI can be of any shape and size. The purpose of the PTS is to track location of personnel in an area using multiple cameras. It can also be used to implement the two-person rule or to detect unauthorized personnel in a restricted area. Finally, the IRS can be used for the recognition and inventory of SNM in a working area. It can also generate a log record on the status of each SNM. Currently the MMS is integrated with PAMTRAK to complement other monitoring technologies in the system. The paper will discuss the system components and their implementations, and describe current enhancements as well as future work.

Sticky foam is an extremely tacky, tenacious material used to entangle and impair an individual. It was developed at Sandia National Laboratories (SNL) in the late 1970`s for usage in nuclear safeguards and security applications. In late 1992, the National Institute of Justice (NIJ), the research arm of the Department of Justice, began a project with SNL to determine the applicability of sticky foam for law enforcement usage. The objectives of the project were to develop a dispenser capable of firing sticky foam, to conduct an extensive toxicology review of sticky foam (formulation SF-283), to test the developed dispenser and sticky foam effectiveness on SNL volunteers acting out prison and law enforcement scenarios, and to have the dispenser and sticky foam further evaluated by correctional representatives. This paper discusses the results of the project.

MOS oxides have been fabricated by oxidation of silicon in N{sub 2}O. Processes studied include oxidation in N{sub 2}O alone, and two-step oxidation in O{sub 2} followed by N{sub 2}O. For both oxides, a nitrogen-rich layer with a peak N concentration of {approximately} 0.5 at. % is observed at the Si-SiO{sub 2} interface with SIMS. Electrical characteristics of N{sub 2}O oxides, such as breakdown and defect generation, are generally improved, especially for the two-step process. Drawbacks typically associated with NH{sub 3}-nitrided oxides such as high fixed oxide charge and enhanced electron trapping, are not observed in N{sub 2}O oxides, which is probably due to their smaller nitrogen content.

The Explosive Inventory and Information System (EIS) is being developed and implemented by Sandia National Laboratories (SNL) to incorporate a cradle to grave structure for all explosives and explosive containing devices and assemblies at SNL from acquisition through use, storage, reapplication, transfer or disposal. The system does more than track all material inventories. It provides information on material composition, characteristics, shipping requirements; life cycle cost information, plan of use; and duration of ownership. The system also provides for following the processes of explosive development; storage review; justification for retention; Resource, Recovery and Disposition Account (RRDA); disassembly and assembly; and job description, hazard analysis and training requirements for all locations and employees involved with explosive operations. In addition, other information systems will be provided through the system such as the Department of Energy (DOE) and SNL Explosive Safety manuals, the Navy`s Department of Defense (DoD) Explosive information system, and the Lawrence Livermore National Laboratories (LLNL) Handbook of Explosives.

This paper describes a method of reducing the mechanical stress caused when a ferrite pot core is encapsulated in a rigid epoxy. the stresses are due to the differences of coefficient of thermal expansion between the two materials. A stress relief medium, phenolic micro-balloon-filled, syntactic polysulfide, is molded into the shape of the pot core. The molded polysulfide is bonded to the core prior to encapsulation. The new package design has made a significant difference in the ability to survive temperature cycles.

This paper provides an overview of the methodology used in a probabilistic transportation risk assessment conducted to assess the probabilities and consequences of inadvertent dispersal of radioactive materials arising from severe transportation accidents. The model was developed for the Defense Program Transportation Risk Assessment (DPTRA) study. The analysis incorporates several enhancements relative to previous risk assessments of hazardous materials transportation including newly-developed statistics on the frequencies and severities of tractor semitrailer accidents and detailed route characterization using the 1990 Census data.

Protecting sensitive items from undetected tampering in an unattended environment is crucial to the success of non-proliferation efforts relying on the verification of critical activities. Tamper Indicating Packaging (TIP) technologies are applied to containers, packages, and equipment that require an indication of a tamper attempt. Examples include: the transportation and storage of nuclear material, the operation and shipment of surveillance equipment and monitoring sensors, and the retail storage of medicine and food products. The spectrum of adversarial tampering ranges from attempted concealment of a pin-hole sized penetration to the complete container replacement, which would involve counterfeiting efforts of various degrees. Sandia National Laboratories (SNL) has developed a technology base for advanced TIP materials, sensors, designs, and processes which can be adapted to various future monitoring systems. The purpose of this technology base is to investigate potential new technologies, and to perform basic research of advanced technologies. This paper will describe the theory of TIP technologies and recent investigations of TIP technologies at SNL.

Becoming aware of the significant events of the past four years and their effect on the expectations to international safeguards, it is necessary to reflect on which direction the development of nuclear safeguards in a new era needs to take and the implications. The lime proven monitoring techniques, based on quantitative factor`s and demonstrated universal application, have shown their merit. However, the new expectations suggest a possibility that a future IAEA safeguards system could rely more heavily on the value of a comprehensive, transparent and open implementation regime. Within such a regime, the associated measures need to be determined and technological support identified. This paper will identify the proven techniques which, with appropriate implementation support, could most quickly make available additional measures for a comprehensive, transparent and open implementation regime. In particular, it will examine the future of Integrated Monitoring Systems and Remote Monitoring in international safeguards, including technical and other related factors.

The upgrade of the TEXTOR tokamak at KFA Juelich was recently completed. This upgrade extended the TEXTOR pulse length from 5 seconds to 10 seconds. The auxiliary heating was increased to a total of 8.0 MW through a combination of neutral beam injection and radio frequency heating. Originally, the inertially cooled armor tiles of the full toroidal belt Advanced Limiter Test -- II (ALT-II) were designed for a 5-second operation with total heating of 6.0 MW. The upgrade of TEXTOR will increase the energy deposited per pulse onto the ALT-II by about 300%. Consequently, the graphite armor tiles for the ALT-II had to be redesigned to avoid excessively high graphite armor surface temperatures that would lead to unacceptable contamination of the plasma. This redesign took the form of two major changes in the ALT-II armor tile geometry. The first design change was an increase of the armor tile thermal mass, primarily by increasing the radial thickness of each tile from 17 mm to 20 mm. This increase in the radial tile dimension reduces the overall pumping efficiency of the ALT-II pump limiter by about 30%. The reduction in exhaust efficiency is unfortunate, but could be avoided only by active cooling of the ALT-II armor tiles. The active cooling option was too complicated and expensive to be considered at this time. The second design change involved redefining the plasma facing surface of each armor tile in order to fully utilize the entire surface area. The incident charged particle heat flux was distributed uniformly over the armor tile surfaces by carefully matching the radial, poloidal and toroidal curvature of each tile to the plasma flow in the TEXTOR boundary layer. This geometry redefinition complicates the manufacturing of the armor tiles, but results in significant thermal performance gains. In addition to these geometry upgrades, several material options were analyzed and evaluated.

Disposition of electric vehicle (EV) batteries after they have reached the end of their useful life is an issue that could impede the widespread acceptance of EVs in the commercial market. This is especially true for advanced battery systems where working recycling processes have not as yet been established. The DOE sponsors an Ad Hoc Electric Vehicle Battery Readiness Working Group to identify barriers to the introduction of commercial EVs and to advise them of specific issues related to battery reclamation/recycling, in-vehicle battery safety, and battery shipping. A Sub-Working Group on the reclamation/recycle topic has been reviewing the status of recycling process development for the principal battery technologies that are candidates for EV use from the near-term to the long-term. Recycling of near-term battery technologies, such as lead-acid and nickel/cadmium, is occurring today and it is believed that sufficient processing capacity can be maintained to keep up with the large number of units that could result from extensive EV use. Reclamation/recycle processes for midterm batteries are partially developed. Good progress has been made in identifying processes to recycle sodium/sulfur batteries at a reasonable cost and pilot scale facilities are being tested or planned. A pre-feasibility cost study on the nickel/metal hydride battery also indicates favorable economics for some of the proposed reclamation processes. Long-term battery technologies, including lithium-polymer and lithium/iron disulfide, are still being designed and developed for EVs, so descriptions for prototype recycling processes are rather general at this point. Due to the long time required to set up new, full-scale recycling facilities, it is important to develop a reclamation/recycling process in parallel with the battery technologies themselves.

The Safeguards Information Management System initiative is a program of the Department of Energy`s (DOE) Office of Arms Control and Nonproliferation aimed at supporting the International Atomic Energy Agency`s (IAEA) efforts to strengthen safeguards through the enhancement of information management capabilities. The DOE hopes to provide the IAEA with the ability to correlate and analyze data from existing and new sources of information, including publicly available information, information on imports and exports, design information, environmental monitoring data, and non-safeguards information. The first step in this effort is to identify and define IAEA requirements. In support of this, we have created a users` requirements document based on interviews with IAEA staff that describes the information management needs of the end user projected by the IAEA, including needs for storage, retrieval, analysis, communication, and visualization of data. Also included are characteristics of the end user and attributes of the current environment. This paper describes our efforts to obtain the required information. We discuss how to accurately represent user needs and involve users for an international organization with a multi-cultural user population. We describe our approach, our experience in setting up and conducting the interviews and brainstorming sessions, and a brief discussion of what we learned.

An input shaping scheme originally used to slew flexible beams via a tabletop D.C. motor is modified for use with an industrial-type, hydraulic-drive robot. This trajectory generation method was originally developed to produce symmetric, rest-to-rest maneuvers of flexible rotating rods where the angular velocity vector and gravitational vector were collinear. In that configuration, out-of-plane oscillations were excited due to centripetal acceleration of the rod. The bang-coast-bang acceleration profile resulted in no oscillations in either plane at the end of the symmetric slew maneuver. In this paper, a smoothed version of the bang-coast-bang acceleration is used for symmetric maneuvers where the angular velocity vector is orthogonal to the gravitational vector. Furthermore, the hydraulic robot servo dynamics are considered explicitly in determining the input joint angle trajectory. An instrumented mass is attached to the tip of a flexible aluminum rod. The first natural frequency of this system is about 1.0Hz. Joint angle responses obtained with encoder sensors are used to identify the servo actuator dynamics.

Multidimensional thermal/chemical modeling is an essential step in the development of a predictive capability for cookoff of energetic materials in systems subjected to abnormal thermal environments. COYOTE II is a state-of-the-art two- and three-dimensional finite element code for the solution of heat conduction problems including surface-to-surface thermal radiation heat transfer and decomposition chemistry. Multistep finite rate chemistry is incorporated into COYOTE II using an operator-splitting methodology; rate equations are solved element-by-element with a modified matrix-free stiff solver, CHEMEQ. COYOTE II is purposely designed with a user-oriented input structure compatible with the database, the pre-processing mesh generation, and the post-processing tools for data visualization shared with other engineering analysis codes available at Sandia National Laboratories. As demonstrated in a companion paper, decomposition during cookoff in a confined or semi-confined system leads to significant mechanical behavior. Although mechanical effect are not presently considered in COYOTE II, the formalism for including mechanics in multidimensions is under development.

The molecular-scale species distributions and intermediate-scale structure of silicate sols influence the microstructures of the corresponding thin films prepared by dip-coating. Using multi-step hydrolysis procedures, the authors find that, depending on the sequence and timing of the successive steps, the species distributions (determined by {sup 29}Si NMR) and intermediate scale structure (determined by SAXS) can change remarkably for sols prepared with the same nominal composition. During film formation, these kinetic effects cause differences in the efficiency of packing of the silicate species, leading to thin film structures with different porosities.

VISAR (Velocity Interferometer System for Any Reflector) is a specialized Doppler interferometer system that is gaining world-wide acceptance as the standard for shock phenomena analysis. The VISAR`s large power and cooling requirements, and the sensitive and complex nature of the interferometer cavity has restricted the traditional system to the laboratory. This paper describes the new portable VISAR, its peripheral sensors, and the role it played in optically measuring ground shock of an underground nuclear detonation (UGT). The Solid State VISAR uses a prototype diode pumped Nd:YAG laser and solid state detectors that provide a suitcase-size system with low power requirements. A special window and sensors was developed for fiber optic coupling (1 kilometer long) to the VISCAR. The system has proven itself as reliable, easy to use instrument that is capable of field test use and rapid data reduction using only a notebook personal computer (PC).

The improvements in purity of molding materials, the IC wafer passivation layers, and manufacturing quality have resulted over the last decade in extremely high reliability in commercial IC packages. In contrast the ceramic/hermetic package world is suffering from limited availability of the newest IC chips, higher cost, larger size, and decreasing quality and fewer manufacturing lines. Traditional manufacturing line qualification tests are a good start for conversion to commercial plastic parts. However, the use of standard sensitive test chips instead of product die is necessary to perform affordable, quantitative evaluations. These test chips have many integrated sensors measuring chemical, mechanical, thermal, and electrical degradation caused by manufacturing and the package environment. Besides visual, electrical test, and burn-in little has been documented on 100% nondestructive screening of plastic molded parts. Based on realistic process control and system engineer cultural expectations, user screening is necessary. Nondestructive tests of moisture and temperature excursion susceptibility are described.

Abstract not provided.

Short communication.

System behaviors can be accurately simulated using artificial neural networks (ANNs), and one that performs well in simulation of structural response is the radial basis function network. A specific implementation of this is the connectionist normalized linear spline (CNLS) network, investigated in this study. A useful framework for ANN simulation of structural response is the recurrent network. This framework simulates the response of a structure one step at a time. It requires as inputs some measures of the excitation, and the response at previous times. On output, the recurrent ANN yields the response at some time in the future. This framework is practical to implement because every ANN requires training, and this is executed by showing the ANN examples of correct input/output behavior (exemplars), and requiring the ANN to simulate this behavior. In practical applications, hundreds or, perhaps, thousands, of exemplars are required for ANN training. The usual laboratory and non-neural numerical applications to be simulated by ANNs produce these amounts of information. Once the recurrent ANN is trained, it can be provided with excitation information, and used to propagate structural response, simulating the response it was trained to approximate. The structural characteristics, parameters in the CNLS network, and degree of training influence the accuracy of approximation. This investigation studies the accuracy of structural response simulation for a single-degree-of-freedom (SDF), nonlinear system excited by random vibration loading. The ANN used to simulate structural response is a recurrent CNLS network. We investigate the error in structural system simulation.

We are improving the understanding of pulsed-power-driven ion diodes using measurements of the charged particle distributions in the diode anode-cathode (AK) gap. We measure the time - and space-resolved electric field in the AK gap using Stark-shifted Li I 2s-2p emission. The ion density in the gap is determined from the electric field profile and the ion current density. The electron density is inferred by subtracting the net charge density, obtained from the derivative of the electric field profile, from the ion density. The measured electric field and charged particle distributions are compared with results from QUICKSILVER, a 3D particle-in-cell computer code. The comparison validates the fundamental concept of electron build-up in the AK gap. However, the PBFA II diode exhibits considerably richer physics than presently contained in the simulation, suggesting improvements both to the experiments and to our understanding of ion diode physics.

The Arrhenius relation predicts a linear relation between log of time to property change and inverse absolute temperature, with the Arrhenius activation energy E{sub a} given from the slope. For a nitrile rubber, Arrhenius behavior is observed for elongation vs air-oven aging temperature, with a E{sub a} of 22 kcal/mol. Confidence in extrapolation to low temperatures can be increased by measuring oxygen consumption. From 95 to 52 C, the E{sub a} for oxygen consumption is identical to that for elongation; however, below 52 C, the E{sub a} for oxygen consumption drops slightly to 18 kcal/mol, indicating that the extrapolation assumption probably overestimates the tensile property lifetime by a factor of about 2 at 23 C.

Prosperity Games are an outgrowth and adaptation of move/countermove and seminar War Games. Prosperity Games are simulations that explore complex issues in a variety of areas including economics, politics, sociology, environment, education and research. These issues can be examined from a variety of perspectives ranging from a global, macroeconomic and geopolitical viewpoint down to the details of customer/supplier/market interactions in specific industries. All Prosperity Games are unique in that both the game format and the player contributions vary from game to game. This report documents the Prosperity Game conducted under the sponsorship of the Electronic Industries Association. Almost all of the players were from the electronics industry. The game explored policy changes that could enhance US competitiveness in the manufacturing of consumer electronics. Four teams simulated a presidentially appointed commission comprised of high-level representatives from government, industry, universities and national laboratories. A single team represented the foreign equivalent of this commission, formed to develop counter strategies for any changes in US policies. The deliberations and recommendations of these teams provide valuable insights as to the views of this industry concerning policy changes, foreign competition, and the development, delivery and commercialization of new technologies.

An assessment of the long term containment capabilities of a possible nuclear waste disposal site requires both an understanding of the hydrogeology of the region under consideration and an assessment of the uncertainties associated with this understanding. Stochastic simulation - the generation of random {open_quotes}realizations{close_quotes} of the regions hydrogeology, consistent with the available information, provides a way to incorporate various types of uncertainty into a prediction of a complex system response such as site containment capability. One statistical problem in stochastic simulation is: What features of the data should be {open_quotes}mimicked{close_quotes} in the realizations? The answer can depend on the application. A discussion is provided of some of the more common data features used in recent applications. These features include spatial covariance functions and measures of the connectivity of extreme values, as examples. Trends and new directions in this area are summarized including a brief description of some statistics (the features) presently in experimental stages.

This report describes the Height of Charge measurement for the Middle Key 4 test conducted at the FCDNA Permanent High Explosives Test Site (PHETS) on 17 September, 1993. The object of the measurement was to monitor remotely the change in the height of the explosive charge suspended above the test pad once the site had been evacuated until detonation. Should the measurement have shown that the charge changed height by more than 15cm then a hold in the test was to be called so that a height adjustment in the suspension system could be made. The measurement system consisted of a remotely placed video camera linked to the test control center-based measurement computer via a fiber optical video data link, a pole mounted stationary reference target, and a target mounted on the charge bag. Measurement of the change in height was determined using image analysis software on frame grabbed images. Measurements indicate that the charge bag did not deviate from the initial surveyed height of 1747cm by more than 1cm between the last measurement made by the survey crew until detonation 40 minutes later.

Vehicle lateral dynamics are affected by vehicle mass, longitudinal velocity, vehicle inertia, and the cornering stiffness of the tires. All of these parameters are subject to variation, even over the course of a single trip. Therefore, a practical lateral control system must guarantee stability, and hopefully ride comfort, over a wide range of parameter changes. This paper describes a robust controller which theoretically guarantees stability over a wide range of parameter changes. The robust controller is designed using a frequency domain transfer function approach. An uncertainty band in the frequency domain is determined using simulations over the range of expected parameter variations. Based on this bound, a robust controller is designed by solving the Nevanlinna-Pick interpolation problem. The performance of the robust controller is then evaluated over the range of parameter variations through simulations.

HEISHI is a Fortran computer model designed to aid in analysis, prediction, and optimization of fuel characteristics for use in Space Nuclear Thermal Propulsion (SNTP). Calculational results include fission product release rate, fuel failure fraction, mode of fuel failure, stress-strain state, and fuel material morphology. HEISHI contains models for decay chain calculations of retained and released fission products, based on an input power history and release coefficients. Decay chain parameters such as direct fission yield, decay rates, and branching fractions are obtained from a database. HEISHI also contains models for stress-strain behavior of multilayered fuel particles with creep and differential thermal expansion effects, transient particle temperature profile, grain growth, and fuel particle failure fraction. Grain growth is treated as a function of temperature; the failure fraction depends on the coating tensile strength, which in turn is a function of grain size. The HEISHI code is intended for use in analysis of coated fuel particles for use in particle bed reactors; however, much of the code is geometry-independent and applicable to fuel geometries other than spherical.

Aging Aircraft NDI Validation Center (AANC) was established by the FAA Technical Center (FAATC) at Sandia National Laboratories in August of 1991. The Validation Center supports the inspection portion of the FAA`s National Aging Aircraft Program which was mandated by Congress in the 1988 Aviation Safety Act. The ultimate customers of the AANC include the FAA, airframe and engine manufacturers, airlines, and third party maintenance facilities. One goal of the AANC is to provide independent validation of technologies intended to enhance the structural inspection of aging commuter and transport aircraft. Another goal is to assist in transferring emerging inspection technology from other parts of the FAA`s program to the aircraft industry. The deliverables from both these activities are an assessment of the reliability and cost benefits of an inspection technology as applied to a particular inspection or class of inspections. The validation process consists of a quantitative and systematic assessment of the reliability and cost/benefits on a Nondestructive Inspection (NDI) process. A NDI process is defined as the NDI systems and procedures used for inspections. This includes the NDI operator, inspection environment, and the object being inspected. The phases of the validation process are: 1. Conceptual, 2. Preliminary design, 3. Final design, and 4. Field implementation. The AAANC usually gets involved in the validation process during Phases 2 and 3. The Center supports field trials with a full array of test specimens and established procedures for conducting the trials. Phase 4 reliability includes field trials using independent inspectors either at the Center`s hangar or at outside maintenance facilities. Three activities are summarized below where inspection technology has been validated in the field. These are: (1) eddy current inspection reliability experiment; (2) magneto optic imager validation; and (3) inspection tool improvement.