Publications

We have developed a new multilayer a-tC material that is thick stress-free, adherent, low friction, and with hardness and stiffness near that of diamond. The new a-tC material is deposited by J pulsed-laser deposition (PLD) at room temperature, and fully stress-relieved by a short thermal anneal at 600°C. A thick multilayer is built up by repeated deposition and annealing steps. We measured 88 GPa hardness, 1100 GPa Young's modulus, and 0.1 friction coefficient (under high load). Significantly, these results are all well within the range reported for crystalline diamond. In fact, this material, if considered separate from crystalline diamond, is the 2nd hardest material known to man. Stress-free a-tC also has important advantages over thin film diamond; namely, it is smooth, processed at lower temperature, and can be grown on a much broader range of substrates. This breakthrough will enable a host of applications that we are actively pursuing in MEMs, sensors, LIGA, etc.

The Integrated Fuel-Coolant Interaction Code (IFCI) is a best-estimate computer program for analysis of phenomena related to mixing of molten nuclear reactor core material with reactor coolant (water). The stand-alone version of the code, IFCI 7.0, has been designed for analysis of small- and intermediate-scale experiments in order to gain insight into the physics (including scaling effects) of molten fuel-coolant interactions. The code's methods, models, and correlations are being assessed. This report describes the flow regime, friction factor, and heat-transfer models used in the current version of IFCI (IFCI 7.0).

Object-oriented analysis methods have been used in the computer science arena for a number of years to model the behavior of computer-based systems. This report documents how such methods can be applied to surety analysis. By embodying the causality and behavior of a system in a common object-oriented analysis model, surety analysts can make the assumptions that underlie their models explicit and thus better communicate with system designers. Furthermore, given minor extensions to traditional object-oriented analysis methods, it is possible to automatically derive a wide variety of traditional risk and reliability analysis methods from a single common object model. Automatic model extraction helps ensure consistency among analyses and enables the surety analyst to examine a system from a wider variety of viewpoints in a shorter period of time. Thus it provides a deeper understanding of a system's behaviors and surety requirements. This report documents the underlying philosophy behind the common object model representation, the methods by which such common object models can be constructed, and the rules required to interrogate the common object model for derivation of traditional risk and reliability analysis models. The methodology is demonstrated in an extensive example problem.

The integrated fuel-coolant interaction (IFCI) computer code is being developed at Sandia National Laboratories to investigate the fuel-coolant interaction (FCI) problem at large scale using a two-dimensional, three-field hydrodynamic framework and physically based models. IFCI will be capable of treating all major FCI processes in an integrated manner. This document is a description of IFCI 7.0. The user's manual describes the hydrodynamic method and physical models used in IFCI 7.0. Appendix A is an input manual provided for the creation of working decks.

We have developed a wafer fusion technology to achieve integration of semiconductor materials and heterostructures with widely disparate lattice parameters, electronic properties, and/or optical properties for novel devices not now possible on any one substrate. Using our simple fusion process which uses low temperature (400-600 C) anneals in inert N{sub 2} gas, we have extended the scope of this technology to examine hybrid integration of dissimilar device technologies. As a specific example, we demonstrate wafer bonding vertical cavity surface emitting lasers (VCSELs) to transparent AlGaAs and GaP substrates to fabricate bottom-emitting short wavelength VCSELs. As a baseline fabrication technology applicable to many semiconductor systems, wafer fusion will revolutionize the way we think about possible semiconductor devices, and enable novel device configurations not possible by epitaxial growth.

In this combination background and position paper, the authors argue that careful work is needed to develop accurate methods for relating the results of fine-scale numerical simulations of material processes to meaningful values of macroscopic properties for use in constitutive models suitable for finite element solid mechanics simulations. To provide a definite context for this discussion, the problem is couched in terms of the lack of general objective criteria for identifying the size of the representative volume (RV) of a material. The objective of this report is to lay out at least the beginnings of an approach for applying results and methods from statistical physics to develop concepts and tools necessary for determining the RV size, as well as alternatives to RV volume-averaging for situations in which the RV is unmanageably large. The background necessary to understand the pertinent issues and statistical physics concepts is presented.

This report is a cradle-to-grave fabrication and postmortem analysis of a sodium-filled heat pipe solar receiver. The Stirling Thermal Motors Gen. H engine was tested with the Thermacore, Inc. heat pipe receiver on Sandia's Test Bed Concentrator II in the fall of 1996. Although engine performance was significantly increased relative to a direct insolation version of the receiver, hot spots did develop on the heat pipe receiver dome. Over the course of a couple of weeks, after tests were completed, the sodium was distilled out of this receiver, and the front dome was removed. Several failure spots and/or cracks (dubbed volcanoes ) were present on the surface of the wick. Postmortem analysis indicates that the cracks in the wick of the heat pipe are not a product of corrosive oxide action. Voids formed within the wick (created either by mechanical or thermal means) serve to concentrate phosphorous from the electroless plating into the liquid sodium. The presence of phosphorous has an apparently harmful effect on the wick. Examination of a virgin piece of the nickel wick material treated in the same manner as the bulk, prior to the introduction of sodium, would be the best baseline sample for comparison. This sample could be analyzed for phosphorous migration into the wick and determine if there is any initial crack formation from the sintering process. Utiortunately a sample of this material was not available during the preparation of this report. Continued work to determine the mechanism of crack formation could significantly increase the hours of available lifetime testing for future solar thermal heat pipe receivers

A tutorial is presented discussing the basic issues associated with propagation of uncertainty analysis and statistical validation of engineering and scientific models. The propagation of uncertainty tutorial illustrates the use of the sensitivity method and the Monte Carlo method to evaluate the uncertainty in predictions for linear and nonlinear models. Four example applications are presented; a linear model, a model for the behavior of a damped spring-mass system, a transient thermal conduction model, and a nonlinear transient convective-diffusive model based on Burger's equation. Correlated and uncorrelated model input parameters are considered. The model validation tutorial builds on the material presented in the propagation of uncertainty tutoriaI and uses the damp spring-mass system as the example application. The validation tutorial illustrates several concepts associated with the application of statistical inference to test model predictions against experimental observations. Several validation methods are presented including error band based, multivariate, sum of squares of residuals, and optimization methods. After completion of the tutorial, a survey of statistical model validation literature is presented and recommendations for future work are made.

In this paper, we report details of our computational study of two shock wave physics experiments performed on the Sandia Z machine in 1998. The novelty of these particular experiments is that they represent the first successful appli- cation of VISAR interferometry to diagnose shock waves generated in experi- mental payloads by the primary X-ray pulse of the machine. We use the Sandia shock-wave physics code ALEGRA to perform the simulations reported in this study. Our simulations are found to be in fair agreement with the time-resolved VISAR experimental data. However, there are also interesting and important discrepancies. We speculate as to future use of time-resolved shock wave data to diagnose details of the Z machine X-ray pulse in the future.

Optical Micro Electro Mechanical Systems (Optical MEMS) Technology holds the promise of one-day producing highly integrated optical systems on a common, monolithic substrate. The choice of fabrication technology used to manufacture Optical MEMS will play a pivotal role in the size, functionality and ultimately the cost of optical Microsystems. By leveraging the technology base developed for silicon integrated circuits, large batches of routers, emitters, detectors and amplifiers will soon be fabricated for literally pennies per part. In this article we review the current status of technologies used for Optical MEMS, as well as fabrication technologies of the future, emphasizing manufacturable surface micromachining approaches to producing reliable, low-cost devices for optical communications applications.

The Sandia National Laboratories (SNL) Data Encryption Standard (DES) Application Specific Integrated Circuit (ASIC) is the fastest known implementation of the DES algorithm as defined in the Federal Information Processing Standards (FIPS) Publication 46-2. DES is used for protecting data by cryptographic means. The SNL DES ASIC, over 10 times faster than other currently available DES chips, is a high-speed, filly pipelined implementation offering encryption, decryption, unique key input, or algorithm bypassing on each clock cycle. Operating beyond 105 MHz on 64 bit words, this device is capable of data throughputs greater than 6.7 Billion bits per second (tester limited). Simulations predict proper operation up to 9.28 Billion bits per second. In low frequency, low data rate applications, the ASIC consumes less that one milliwatt of power. The device has features for passing control signals synchronized to throughput data. Three SNL DES ASICS may be easily cascaded to provide the much greater security of triple-key, triple-DES.

We have observed low threshold operation of a broadly tunable (2.18-3.4 µm) pump-resonant cw periodically poled lithium niobate (PPLN) optical parametric oscillator (OPO). When pumped at 806 nm with 410 mW from a custom-built diode laser the OPO generated 20 mW of idler output at 3.3 µm.

Anisotropic, smooth etching of the group-III nitrides has been reported at relatively high rates in high-density plasma etch systems. However, such etch results are often obtained under high de-bias andlor high plasma flux conditions where plasma induced damage can be significant. Despite the fact that the group-III nitrides have higher bonding energies than more conventional III-V compounds, plasma-induced etch damage is still a concern. Attempts to minimize such damage by reducing the ion energy or increasing the chemical activity in the plasma often result in a loss of etch rate or anisotropy which significantly limits critical dimensions and reduces the utility of the process for device applications requiring vertical etch profiles. It is therefore necessary to develop plasma etch processes which couple anisotropy for critical dimension and sidewall profile control and high etch rates with low-damage for optimum device performance. In this study we report changes in sheet resistance and contact resistance for n- and p-type GaN samples exposed to an Ar inductively coupled plasma (ICP). In general, plasma-induced damage was more sensitive to ion bombardment energies as compared to plasma flux. In addition, p-GaN was typically more sensitive to plasma-induced damage as compared to n-GaN.

We are developing a method for the real-time analysis of airborne microparticles based on laser ablation mass spectroscopy. Airborne particles enter an ion trap mass spectrometer through a differentially-pumped inlet, are detected by light scattered from two CW laser beams, and sampled by a 10 ns excimer laser pulse at 308 nm as they pass through the center of the ion trap electrodes. After the laser pulse, the stored ions are separated by conventional ion trap methods. In this work thousands of positive and negative ion spectra were collected for eighteen different species: six bacteria, six pollen, and six particulate samples. The data were then averaged and analyzed using the Multivariate Patch Algorithm (MPA), a variant of traditional multivariate anal ysis. The MPA correctly identified all of the positive ion spectra and 17 of the 18 negative ion spectra. In addition, when the average positive and negative spectra were combined the MPA correctly identified all 18 species. Finally, the MPA is also able to identify the components of computer synthesized mixtures of the samples studied

We study the low-temperature in-plane magnetoresistance of tunnel-coupled quasi-one-dimensional quantum wires. The wires are defined by two pairs of mutually aligned split gates on opposite sides of a < 1 micron thick AlGaAs/GaAs double quantum well heterostructure, allowing independent control of their widths. In the ballistic regime, when both wires are defined and the field is perpendicular to the current, a large resistance peak at ~6 Tesla is observed with a strong gate voltage dependence. The data is consistent with a counting model whereby the number of subbands crossing the Fermi level changes with field due to the formation of an anticrossing in each pair of 1D subbands.

On November 23, 1998, an 18,000-foot-deep wild-cat natural gas well being drilled near Bakersfield, CA blew out and caught fire. All attempts to kill this well failed, and the well continues to flow under limited control, producing large volumes of natural gas, salt water, and some oil. The oil and some of the water is being separated and trucked off site, and the remaining gas and water is being burned at the well head. A relief well is being drilled approximately one-quarter mile away in an attempt to intercept the first well. If the relief well is successful, it will be used to cement in and kill the first well. Epoch Wellsite Services, Inc., the mud-logging company for the initial well and the relief well, requested Sandia's rolling float meter (RFM) for these critical drilling operations. The RFM is being used to measure the mud outflow rate and detect kicks while drilling the relief well, which will undoubtedly encounter reservoir conditions similar to those responsible for the blow out. Based on its prior experience with the RFM, Epoch believes that it is the only instrument capable of providing the level of accuracy and response to mudflow needed to quickly detect kicks and minimize the risk of a blowout on this second critical well. In response to the urgent request from industry, Sandia and Epoch technicians installed the RFM on the relief well return line, and completed its initial calibration. The data from the RFM is displayed in real-time for the driller, the companyman, and the toolpusher via Epochs RIGWATCH Drilling Instmmentation System. The RFM has already detected several small kicks while drilling toward the annulus of the blown out well. A conventional paddle meter is located downstream of the RFM to provide redundancy and the opportunity to compare the two meters in an actual drilling operation, The relief well is nearing 14,000 feet deep, targeting an intercept of the first well near 17,600 feet. The relief well is expected to be completed in about 30 days. Several other Sandia instruments being developed for geothermal drilling are also being evaluated during this operation, Successful performance of these instruments on this important drilling job will reinforce our efforts to commercialize this technology for the geothermal and oil and gas drilling industries. Sandia's Rolling Float Meter was developed through the Lost Circulation Technology Program sponsored by the U. S. Department of Energy, Office of Geothermal Technologies. It monitors drilling fluid returns to rapidly detect loss of circulation during geothermal drilling. Lost circulation is particularly prevalent in geothermal wells, and can add as much as 10% to the total cost of drilling the well. Consequently, rapid detection and treatment of lost circulation is necessary for cost- effective geothermal drilling. Sandia has been evaluating and demonstrating the capabilities of the RFM to the geothermal industry for several years. In addition to lost circulation, the RFM is also useful for accurately detecting well kicks. Contacts have been made with mud logging companies that are involved with both geothermal and oil and gas drilling operations.

Microstructure in the reaction interface between molten Al and dense mullite have been studied by transmission electron microscopy to provide insight into mechanisms for forming ceramic-metal composites by reactive metal penetration. The reactions, which have the overall stoichiometry, 3Al#iz01~ + (8+ x)A1 + 13 AlzO~ + xA1 + 6Si, were carried out at temperatures of 900, 1100, and 1200oC for 5 minutes and 60 minutes, and 1400oC for 15 minutes. Observed phases generally were those given in the above reaction, although their proportions and interracial rnicrostructures differed strongly with reaction temperature. After reaction at 900oC, a thin Al layer separated unreacted mullite from the cx-AlzO~ and Al reaction products. No Si phase was found near the reaction front. After 5 minutes at 1100"C, the nxtction front contained Si, ct-A120~, and an aluminum oxide phase with a high concentration of Si. After 60 minutes at 11O(YC many of the cx-A120g particles were needle-shaped with a preferred orientation. After reaction at 1200oC, the reaction front contained a high density of Si particles that formed a continuous layer over many of the mullite grains. The sample reacted at 140VC for 15 minutes had a dense ct-A120J reaction layer less than 2~m thick. Some isolated Si particles were present between the a-AlzO~ layer and the unreacted mullite. Using previously measured reaction kinetics data, the observed temperature dependence of the interracial microstructure have been modeled as three sequential steps, each one of which is rate-limiting in a different temperature range.

Arbitrary Lagrangian Eulerian (ALE) computational techniques allow treatment of gases, liq- uids, and solids in the same simulation. ALE methods include the ability to treat shockwaves in gases, liquids, and solids and the interaction of shockwaves with each other and with media from one of the other categories. ALE codes can also treat explosive detonation and the expansion of the explosive gases and their interaction with air and solids. ALEGRA is a 3-DALE code that has been developed at Sandia National Laboratories over the past few years. ALEGRA has been applied to a 2-D simulation of presplitting using decoupled explosives in rock blasting with very interesting results. The detonation of the explosive at the bottom of the hole sends a shock wave up the borehole driven by the explosive gas expanding into air. The explosive gas compresses the air against the stemming column where it rebounds and recompresses at the bottom of the borehole. This type of ringing takes several cycles to damp out. The explosively induced expansion of the borehole is also treated by ALEGRA as well as the shock wave imparted to the rock. The presentation of this paper will include sev- eral computer animations to aid in understanding this complex phenomenon.

This criticality safety analysis is performed to determine the effective multiplication factor (k_eff) for a storage cabinet filled with unirradiated Cintichem-type targets. These targets will be used to produce ⁹⁹Mo at Sandia National Laboratories and will be stored on-site prior to irradiation in the Annular Core Research Reactor. The analysis consisted of using the Monte Carlo code MCNP (Version 4A) to model and predict the k_eff for the proposed dry storage configuration under credible loss of geometry and moderator control. Effects of target pitch, non-uniform loading, and target internal/external flooding are evaluated. Further studies were done with deterministic methods to verify the results obtained from MCNP and to obtain a clearer understanding of the parameters affecting system criticality. The diffusion accelerated neutral particle transport code ONEDANT was used to model the target in a one-dimensional, infinite half-slab geometry and determine the critical slab thickness. Hand calculations were also completed to determine the critical slab thickness with modified one-group, and one-group, two region approximations. Results obtained from ONEDANT and the hand calculations were compared to applicable cases in a commonly used criticality safety analysis handbook. Overall, the critical slab thicknesses obtained in the deterministic analysis were much larger than the dimensions of the cabinet and further support the predictions by MCNP that a critical system cannot be attained for the base case or in conditions where loss of geometry and moderation control occur.

Localization of light to less than a cubic wavelength, {lambda}{sup 3}, has important quantum consequences. The creation of single mode cavities and the modification of spontaneous emission are two important examples. A defect formed inside a three-dimensional (3D) photonic crystal provides an unique optical environment for light localization. Single mode defect cavities were built, for the first time, from an infrared 3D photonic crystal. A cavity state with modal volume of less than one {lambda}{sup 3} was observed.

Two main assumptions which underlie the Stoney formula relating substrate curvature to mis-match strain in a bonded thin film are that the film is very thin compared to the substrate, and the deformations are infinitesimally small. Expressions for the curvature-strain relastionship are derived for cases in which thses assumptions are relaxed, thereby providing a biasis for interpretation of experimental observations for a broader class of film-substrate configurations.

The formation of quantum wires has much interest due to their novel electronic properties which may lead to enhanced optoelectronic device performance and greater photovoltaic efficiencies. One method of forming these structures is through spontaneous lateral modulation found during the epitaxial growth of III/V alloys. In this paper, we report and summarize our investigations on the formation of lateral moduation in the MBE grown InAlAs/InP(001) system. This system was grown as a short-period superlattice where n-monolayers of InAs are deposited followed by m-Monolayers of AlAs (with n and m~2) and this sequence is repeated to grown a low strain InAlAs ternary alloy on InP(001) that exhibits lateral modulation. Films were grown under a variety of condition (growth temperature, effective alloy composition, superlattice period, and growth rate). These films have been extensively analyzed using X-ray diffraction, atomic force microscopy, and transmission electron microscopy (TEM) and microcharacterization, in addition to photon-based spectroscopes. Here we present results of several microstructural characterizations using a wide range of TEM-based techniques, and compare them to results from the other methods to obtain a unified understanding of composition modulation. Two strong points consistently emerge: 1) The lateral modulation wavelength is insensitive to growth temperature and effective alloy composition, but the strength of the lateral modulation is greatest near an effective alloy composition of In(0.46)Al(0.54)As, which corresponds to a slightly tensile global strain with respect to InP. 2) The composition variation for the strongly modulated films is as much as 0.38 InAs mole fraction. In addition, for these strongly modulated films, the modulation wave is asymmetric showing strongly peaked, narrower InAs-rich regions separated by flat AlAs-rich regions. We discuss these results and their possible implications in addition to detailing the techniques used to obtain them.

Pattern formation on surfaces undergoing low-energy ion bombardment is a common phenomenon. Here, a recently developed in situ spectroscopic light scattering technique was used to monitor periodic ripple evolution on Si(001) during Ar(+) sputtering. Analysis of the rippling kinetics indicated that under high flux sputtering at low temperatures the concentration of mobile species on the surface is saturated, and, surprisingly, is both temperature and ion flux independent. This is due to an effect of ion collision cascades on the concentration of mobile species. This new understanding of surface dynamics during sputtering allowed us to measure straighforwardly the activation energy for atomic migration on the surface to be 1.2+0.1 eV. The technique is generalizable to any material, including high temperature and insulating materials for which surface migration energies are notoriously difficult to measure.

The suitability of the wavelength range provided by silicon photodiode detector arrays for monitoring the spectral reflectance during epitaxial growth of GaSb, AlGaAsSb, and GaInAsSb, which have cutoff wavelengths at 25 degree C of 1.7, 1.2, and 2.3 um, respectively, is demonstrated. These alloys were grown lattice matched to GaSb in a vertical rotating-disk reactor, which was modified to accommodate near normal reflectance without affecting epilayer uniformity, By using a virtual interface model, the growth rate and complex refractive index at the growth temperature are extracted for these alloys over the 600 to 1000 nm spectral range. Excellent agreement is obtained between the extracted growth rate and that determined by ex-situ measurement.

The porosities of three mesoporous silica materials were characterized with {sup 129}Xe NMR spectroscopy. The materials were synthesized by a sol-gel process with r = 0, 25, and 70% methanol by weight in an aqueous cetyltrimethylammonium bromide solution. Temperature dependent chemical shifts and spin lattice relaxation times reveal that xenon does not penetrate the pores of the largely disordered (r= 70%) silica. For both r = 0 and 25%, temperature dependent resonances corresponding to physisorbed xenon were observed. An additional resonance for the r = 25% sample was attributed to xenon between the disordered cylindrical pores. 2D NMR exchange experiments corroborate the spin lattice relaxation data which show that xenon is in rapid exchange between the adsorbed and the gas phase.

The authors present a compact, robust, solid-state blue light (490 nm) source capable of greater than 5 mW of output in a TEM{sub 00} mode. This device is an optically pumped, vertical external-cavity surface-emitting laser (VECSEL) with an intracavity frequency doubling crystal.

Deposition parameters were found to have a marked effect on piezoelectric response of reactive radio frequency (RF) sputtered AlN thin films. The authors observed peizoelectric response values ranging from {minus}3.5 to +4.2 pm/V for 1 {micro}m thick AlN films deposited onto Ti/Ru electrode stacks. An investigation of the effects of deposition parameters, in particular the nature of the Ru/AlN interface, was conducted. The lag time between deposition of adjacent thin film layers appeared to have the greatest affect on the value of the piezoelectric response. This suggests that chemical reaction occurring on the Ru thin film surface is responsible for changing an important thin film property such as dipole orientation within the overlying AlN thin film.

In this paper, we introduce a new approach for altering the properties of bridged polysilsesquioxane xerogels using post-processing modification of the polymeric network. The bridging organic group contains latent functionalities that can be liberated thermally, photochemically, or by chemical means after the gel has been processed to a xerogel. These modifications can produce changes in density, volubility, porosity, and or chemical properties of the material. Since every monomer possesses two latent functional groups, the technique allows for the introduction of high levels of functionality in hybrid organic-inorganic materials. Dialkylenecarbonate-bridged polysilsesquioxane gels were prepared by the sol-gel polymerization of bis(triethoxysilylpropyl)carbonate (1) and bis(triethoxysilylisobutyl)-carbonate (2). Thermal treatment of the resulting non-porous xerogels and aerogels at 300-350 C resulted in quantitative decarboxylation of the dialkylenecarbonate bridging groups to give new hydroxyalkyl and olefinic substituted polysilsesquioxane monolithic xerogels and aerogels that can not be directly prepared through direct sol-gel polymerization of organotrialkoxysilanes.

JavaScript allows the definition and use of large, complex objects. Unlike some other object-oriented languages, it also allows run-time modifications not only of the values of object components, but also of the very structure of the object itself. This feature is powerful and sometimes very convenient, but it can be difficult to keep track of the object's structure and values throughout program execution. What's needed is a simple way to view the current state of an object at any point during execution. There is a debug function that is included in the Netscape server-side JavaScript environment. The function outputs the value(s) of the expression given as the argument to the function in the JavaScript Application Manager's debug window [SSJS].

Traditional safety and reliability analysis methods are applicable to many standard problems, including those examples illustrated in most formal courses. However, there are many real-world situations for which non-traditional methods appear to be more appropriate, mainly because most practical problems involve substantial subjectivity about the inputs and models used. This paper surveys some of the most applicable approaches found in a recent research study. Each approach is developed individually and is illuminated by selecting example situations of apparent applicability. Then, the combinational blending of the approaches with each other and with traditional methodology is discussed.

Work of adhesion (Wa) measurements are being studied for several types of polymer/metal combinations in order to obtain a better understanding of the adhesive failure mechanisms for systems containing encapsulated and bonded components. A primary concern is whether studies of model systems can be extended to systems of technological interest. One study performed in our laboratory involved the determination of Wa between silicone (PDMS) and Al surfaces in order to establish potential adhesive failure mechanisms. Our initial work with PDMS was based on Dow Corning 170 Sylgard. PDMS hemispheres were synthesized following the procedure outlined by Chaudhury and Whitesides where the filler was stripped from the commercial silicone by centrifuging. Wa between PDMS surfaces was determined using the JKR method. Our results for the Wa of PDMS were in agreement with those reported by Chaudhury and Whitesides. However, further JKR studies using these PDMS hemispheres on flat Al surfaces were fraught with difficulty. We could not discriminate hydrogen-bonding effects between Al{sub 2}O{sub 3} and hydroxyl groups in the PDMS and other possible bonding mechanisms. It was suggested that commercial systems contain inhibitors and additives that interfere with understanding the PMDS/Al interface. Therefore, the current study uses pure PDMS networks synthesized in our lab. Also, two contact mechanics methods were deployed to measure the Wa--JKR method using two hemispheres and a LEFM method using a cylinder containing a circumferential crack. This paper contains a description of the synthesis of the PDMS used for these studies and the determination of Wa between PDMS surfaces using the JKR method, contact angle measurements, and a LEFM method that consists of a cylinder containing a circumferential crack.

This editorial paper presents a vision for intelligent health care in the home of the future, focusing on technologies with the highest potential payoff given targeted government funding over the next ten years. A secure, plug-and-play information framework provides the starting point for identifying technologies that must be developed before home-based devices can know their context and assimilate information to support care decisions.

We propose an object-oriented information architecture for telemedicine systems that promotes secure `plug-and-play' interaction between system components through standardized interfaces, communication protocols, messaging formats, and data definitions. In this architecture, each component functions as a black box, and components plug together in a ''lego-like'' fashion to achieve the desired device or system functionality. Introduction Telemedicine systems today rely increasingly on distributed, collaborative information technology during the care delivery process. While these leading-edge systems are bellwethers for highly advanced telemedicine, most are custom-designed and do not interoperate with other commercial offerings. Users are limited to a set of functionality that a single vendor provides and must often pay high prices to obtain this functionality, since vendors in this marketplace must deliver en- tire systems in order to compete. Besides increasing corporate research and development costs, this inhibits the ability of the user to make intelligent purchasing decisions regarding best-of-breed technologies. This paper proposes a reference architecture for plug-and-play telemedicine systems that addresses these issues.

Global Nuclear Materials Management (GNMM) anticipates and supports a growing international recognition of the importance of uniform, effective management of civilian, excess defense, and nuclear weapons materials. We expect thereto be a continuing increase in both the number of international agreements and conventions on safety, security, and transparency of nuclear materials, and the number of U.S.-Russian agreements for the safety, protection, and transparency of weapons and excess defense materials. This inventory of agreements and conventions may soon expand into broad, mandatory, international programs that will include provisions for inspection, verification, and transparency, To meet such demand the community must build on the resources we have, including State agencies, the IAEA and regional organizations. By these measures we will meet the future expectations for monitoring and inspection of materials, maintenance of safety and security, and implementation of transparency measures.

Sandia has implemented a formal process to verify that new or modified facilities and operations are ready to safely operate. The readiness review process focuses on the status of management systems, personnel, and systems, structures, and components to do work safely. The scope and depth of the review are tailored to match the potential consequences and the likelihood that the consequences could occur. The precepts and methodology of the process are applicable to verifying the readiness of enterprise systems, and should comprise the final element in developing and implementing an enterprise system. This paper describes the readiness review process, the key elements for success, lessons learned from Sandia's readiness assessment process, and outlines how the process can be applied to enterprise systems. Specific topics addressed include selecting the criteria, approach, and lines of inquiry to be used for the review; selecting members for the review team; team leader responsibilities; reporting and closing deficiencies; and, responsibilities of the facility/project owner and management.

Irradiation of red meat and poultry has been approved by the U.S. FDA, and the U.S. Department of Agriculture's rule for processing red meat is out for comment. Looking beyond the current issues of packaging materials, labeling, and consumer acceptance, this paper reviews the next step of implementation and how to remove, or at least reduce, the barriers to utilization. Polls of the user community identified their requirements for electron beam or x-ray processing of meat or poultry and their concerns about implementation for on-line processing. These needs and issues are compared to the capabilities of the accelerator industry. The critical issues of beam utilization and dose uniformity, factors affecting floor space requirements, and treatment costs are examined.

Boolean logic expressions are often derived in safety and reliability analysis. Since the values of the operands are rarely exact, accounting for uncertainty with the tightest justifiable bounds is important. Accurate determination of result bounds is difficult when the inputs have constraints. One example of a constraint is that an uncertain variable that appears multiple times in a Boolean expression must always have the same value, although the value cannot be exactly specified. A solution for this repeated variable problem is demonstrated for two Boolean classes. The classes, termed functions with unate variables (including, but not limited to unate functions), and exclusive-or functions, frequently appear in Boolean equations for uncertain outcomes portrayed by logic trees (event trees and fault trees).

This paper presents results from a series of preliminary tests to evaluate a scannerless range-imaging device as a potential sensory enhancement tool for divers and as a potential identification sensor for deployment on small unmanned underwater vehicles. The device, developed by Sandia National Laboratories, forms an image on the basis of point-to-point range to the target rather than an intensity map. The range image is constructed through a classical continuous wave phase detection technique in which the light source is amplitude modulated at radio frequencies. The receiver incorporates a gain-modulated image intensifier, and range information is calculated on the basis of the phase difference between the transmitted and reflected signal. The initial feasibility test at the Coastal Systems Station showed the device to be effective at imaging low-contrast underwater targets such as concertina wire. It also demonstrated success at imaging a 21-inch sphere at a depth of 10 feet in the water column through a wavy air-water interface.

In 1991, the Federal Aviation Administration (FAA) established an Airworthiness Assurance NDI Validation Center (AANC) at Sandia National Laboratories. Its primary mission is to support technology development, validation, and transfer to industry in order to enhance the airworthiness and improve the aircraft maintenance practices of the U.S. commercial aviation industry. The Center conducts projects in a myriad of engineering disciplines. The results are placed in the public domain so that the industry at-large can reap the benefits of FAA-funded Research and Development efforts. To support the Center's goals, the FAA/AANC has set up a hangar facility at the Albuquerque International Airport which contains a collection of transport and commuter aircraft as well as other test specimens. The facility replicates a working maintenance environment by incorporating both the physical inspection difficulties as well as the environmental factors which influence maintenance reliability.

Over a period of 15 months, five sets of adhesively-bonded butt joints were fabricated and tested. This previously unreported data is used to assess the variability of measured interface corner toughness values, K{sub ac}, as well as the dependence of K{sub ac} on surface preparation. A correlation between K{sub ac} and the size of the adhesive failure zone is also noted.

The authors consider a chain of elastic (Hertzian) grains that repel upon contact according to the potential V = a{delta}{sup u}, u > 2, where {delta} is the overlap between the grains. They present numerical and analytical results to show that an impulse initiated at an end of a chain of Hertzian grains in contact eventually propagates as a soliton for all n > 2 and that no solitons are possible for n {le} 2. Unlike continuous, they find that colliding solitons in discrete media initiative multiple weak solitons at the point of crossing.

Abstract not provided.

This paper outlines general physical and computational issues associated with performing numerical simulation of fire suppression. Fire suppression encompasses a broad range of chemistry and physics over a large range of time and length scales. The authors discuss the dominant physical/chemical processes important to fire suppression that must be captured by a fire suppression model to be of engineering usefulness. First-principles solutions are not possible due to computational limitations, even with the new generation of tera-flop computers. A basic strategy combining computational fluid dynamics (CFD) simulation techniques with sub-grid model approximations for processes that have length scales unresolvable by gridding is presented.

As we enter the new millennium, let us recognize that the losses resulting from natural or malevolent events that cause major property damage, severe injuries, and unnecessary death are not always due to forces beyond our control. We can prevent these losses by changing the way we think and act about design and construction projects. New tools, technologies, and techniques can improve structural safety, security, and reliability and protect owners, occupants, and users against loss and casualties. Hurricane Mitch, the African embassy bombings, the ice storms in Canada and the northeastern US last winter, the Oklahoma City bombing, flooding and earthquakes in California, tornadoes and flooding in Florida, and wildfires in the Southwest are threats to the safety and security of the public and the reliability of our constructed environment. Today's engineering design community must recognize these threats and address them in our standards, building codes, and designs. We know that disasters will continue to strike and we must reduce their impact on the public. We must demand and create innovative solutions that assure a higher level of structural performance when disasters strike.

Z-pinches created using the Z accelerator generate {approximately}220 TW, 1.7 MJ radiation pulses that heat large ({approximately}10 cm{sup 3}) hohlraums to 100-150 eV temperatures for times of order 10 nsec. We are performing experiments exploiting this intense radiation to drive shock waves for equation of state studies. The shock pressures are typically 1-10 Mbar with 10 nsec duration in 6-mm-diameter samples. In this paper we demonstrate the ability to perform optical spectroscopy measurements on shocked samples located in close proximity to the z-pinch. These experiments are particularly well suited to optical spectroscopy measurements because of the relatively large sample size and long duration. The optical emission is collected using fiber optics and recorded with a streaked spectrograph. Other diagnostics include VISAR and active shock breakout measurements of the shocked sample and a suite of diagnostics that characterize the radiation drive. Our near term goal is to use the spectral emission to obtain the temperature of the shocked material. Longer term objectives include the examination of deviations of the spectrum from blackbody, line emission from lower density regions, determination of kinetic processes in molecular systems, evaluation of phase transitions such as the onset of metalization in transparent materials, and characterization of the plasma formed when the shock exits the rear surface. An initial set of data illustrating both the potential and the challenge of these measurements is described.

Sandia Laboratories' computational scientists are addressing a very important question: How do we get insight from the human combined with the computer-generated information? The answer inevitably leads to using scientific visualization. Going one technology leap further is teraflop visualization, where the computing model and interactive graphics are an integral whole to provide computing for insight. In order to implement our teraflop visualization architecture, all hardware installed or software coded will be based on open modules and dynamic extensibility principles. We will illustrate these concepts with examples in our three main research areas: (1) authoring content (the computer), (2) enhancing precision and resolution (the human), and (3) adding behaviors (the physics).

Over the past two years, New Mexico has been engaged in a significant new approach to implement large purchases of solar power. This effort followed a regulatory process that treated solar power generation similar to conventional generation obtained by an investor-owned utility under the regulation of a public utility commission. In 1997, Public Service Company of New Mexico (PNM) gained approval to purchase power from a 100-MW combustion turbine facility that would be owned and operated by a wholesale generator. At the same time it issued the approval, and following discussions with the utility, the New Mexico Public Utility Commission (NMPUC) also required PNM to issue a request for proposal for a 5-MW central station solar facility, a major step for solar technologies in the state, in what would be the world's largest of its technology type. In cooperation with the staff of the NMPUC, PNM reviewed the proposals received, and Applied Power Corporation was selected for the photovoltaic portion of the proposed plan; retaining ownership of the plant, assuming the risks connected with the technology, and operating the plant in exchange for a power purchase agreement in a first-of-its-kind contract for photovoltaics. During the NMPUC hearings, various parties raised significant opposition to the cost-recovery mechanism that was proposed and voiced issues about the type of solar plant, its size, cost and the tiding approaches to building it. Because of these issues, alternative proposals were put forth that reduced the size and costs of the plant and had implied changes in ownership and risks. The order issued by the NMPUC on October 21, 1998, requires PNM to impose a charge of 0.5% on its retail electric customers' monthly bills to be used to acquire the solar facilities, but also to obtain other renewable electric power resources, both on a pay-as-you-go basis. This paper identifies the issues and their resolution that similar projects are expected to encounter.

We conducted three sets of depth-of-penetration experiments with limestone targets and 3.0 caliber-radius-head (CRH), ogive-nose steel rod projectiles. The limestone targets had a nominal unconfined compressive strength of 60 MPa, a density of 2.31 kg/m{sup 3}, a porosity of 15%, and a water content less than 0.4%. The ogive-nose rod projectiles with length-to-diameter ratios often were machined from 4340 R{sub c} 45 and Aer Met 100 R{sub c} 53 steel, round stock and had diameters and masses of 7.1 mm, 0.020 kg; 12.7 mm, 0.117 kg; and 25.4 mm, 0.931 kg. Powder guns or a two-stage, light-gas gun launched the projectiles at normal impacts to striking velocities between 0.4 and 1.9 km/s. For the 4340 R{sub c} 45 and Aer Met 100 R{sub c} 53 steel projectiles, penetration depth increased as striking velocity increased to a striking velocity of 1.5 and 1.7 km/s, respectively. For larger striking velocities, the projectiles deformed during penetration without nose erosion, deviated from the shot line, and exited the sides of the target. We also developed an analytical penetration equation that described the target resistance by its density and a strength parameter determined from depth of penetration versus striking velocity data.

The delivery of the first one tera-operations/sec computer has significantly impacted production data visualization, affecting data transfer, post processing, and rendering. Terascale computing has motivated a need to consider the entire data visualization system; improving a single algorithm is not sufficient. This paper presents a systems approach to decrease by a factor of four the time required to prepare large data sets for visualization.For daily production use, all stages in the processing pipeline from physics simulation code to pixels on a screen, must be balanced to yield good overall performance. Also, to complete the data path from screen to the analyst's eye, user display systems for individuals and teams are examined. Performance of the initial visualization system is compared with recent improvements. Lessons learned from the coordinated deployment of improved algorithms are also discussed, including the need for 64 bit addressing and a fully parallel data visualization pipeline.

An evaluation of biotic and abiotic attenuation processes potentially important to chlorinated and non-chlorinated volatile organic compound (VOC) fate and transport in the 148 meter thick vadose zone beneath the Chemical Waste Landfill (CWL) was conducted. A unique feature of this evaluation is the comparison of two estimates of VOC mass present in the soil gas, pore-water, and solid phases (but not including mass as non-aqueous phase liquid [NAPL]) of the vadose zone in 1993. One estimate, 1,800 kg, was obtained from vadose zone transport modeling that incorporated molecular diffusion and volatilization to the atmosphere, but not biotic or chemical processes. The other estimate, 2,120 kg, was obtained from the sum of VOC mass physically removed during soil vapor extraction and an estimate of VOC mass remaining in the vadose zone in 1998, both adjusted to exclude NAPL mass. This comparison indicates that biogeochemical processes were at best slightly important to historical VOC plume development. Some evidence of aerobic degradation of non-chlorinated VOCs and abiotic transformation of 1,1,1-Trichloroethane was identified. Despite potentially amenable site conditions, no evidence was found of cometabolic and anaerobic transformation pathways. Relying principally on soil-gas analytical results, an upper-bound estimate of 21% mass reduction due to natural biogeochemical processes was developed. Although available information for the CWL indicates that natural attenuation processes other than volatilization to the atmosphere did not effective y enhance groundwater protection, these processes could be important in significantly reducing groundwater contamination and exposure risks at other sites. More laboratory and field research is required to improve our collective ability to characterize and exploit natural VOC attenuation processes, especially with respect to the combination of relatively thick and dry vadose zones and chlorinated VOCs.