Publications

Abstract not provided.

Cadmium plating on metal surfaces is commonly used for corrosion protection and to achieve good solderability on the 304L stainless steel shell of the MC4636 lightning arrestor connector (LAC) for the W76-1 system. This study examined the use of zinc as a potential substitute for the cadmium protective surface finish. Tests were performed with an R and RMA flux and test temperatures of 230 C, 245 C, and 260 C. Contact angle, {theta}{sub c}, served as the generalized solderability metric. The wetting rate and wetting time parameters were also collected. The solderability ({theta}{sub c}) of the Erie Plating Cd/Ni coatings was better than that of similar Amphenol coatings. Although the {theta}{sub c} data indicated that both Cd/Ni platings would provide adequate solderability, the wetting rate and wetting time data showed the Amphenol coatings to have better performance. The Zn/Ni coatings exhibited non-wetting under all flux and temperature conditions. Based on the results of these tests, it has been demonstrated that zinc plating is not a viable alternate to cadmium plating for the LAC connectors.

Abstract not provided.

A major research goal of the national spherical torus experiment is establishing long-pulse, high beta, high confinement operation and its physics basis. This research has been enabled by facility capabilities developed during 2001 and 2002, including neutral beam (up to 7 MW) and high harmonic fast wave (HHFW) heating (up to 6 MW), toroidal fields up to 6 kG, plasma currents up to 1.5 MA, flexible shape control, and wall preparation techniques. These capabilities have enabled the generation of plasmas with {beta}{sub T} {triple_bond} <p>/(B{sub T0}{sup 2}/2{mu}{sub 0}) of up to 35%. Normalized beta values often exceed the no-wall limit, and studies suggest that passive wall mode stabilization enables this for H mode plasmas with broad pressure profiles. The viability of long, high bootstrap current fraction operations has been established for ELMing H mode plasmas with toroidal beta values in excess of 15% and sustained for several current relaxation times. Improvements in wall conditioning and fueling are likely contributing to a reduction in H mode power thresholds. Electron thermal conduction is the dominant thermal loss channel in auxiliary heated plasmas examined thus far. HHFW effectively heats electrons, and its acceleration of fast beam ions has been observed. Evidence for HHFW current drive is obtained by comparison of the loop voltage evolution in plasmas with matched density and temperature profiles but varying phases of launched HHFW waves. Studies of emissions from electron Bernstein waves indicate a density scale length dependence of their transmission across the upper hybrid resonance near the plasma edge that is consistent with theoretical predictions. A peak heat flux to the divertor targets of 10 MW m{sup -2} has been measured in the H mode, with large asymmetries being observed in the power deposition between the inner and outer strike points. Non-inductive plasma startup studies have focused on coaxial helicity injection. With this technique, toroidal currents up to 400 kA have been driven, and studies to assess flux closure and coupling to other current drive techniques have begun.

Research on the spherical torus (or spherical tokamak) (ST) is being pursued to explore the scientific benefits of modifying the field line structure from that in more moderate aspect ratio devices, such as the conventional tokamak. The ST experiments are being conducted in various US research facilities including the MA-class National Spherical Torus Experiment (NSTX) at Princeton, and three medium sized ST research facilities: PEGASUS at University of Wisconsin, HIT-II at University of Washington, and CDX-U at Princeton. In the context of the fusion energy development path being formulated in the US, an ST-based Component Test Facility (CTF) and, ultimately a Demo device, are being discussed. For these, it is essential to develop high performance, steady-state operational scenarios. The relevant scientific issues are energy confinement, MHD stability at high beta ({beta}), non-inductive sustainment, Ohmic-solenoid-free start-up, and power and particle handling. In the confinement area, the NSTX experiments have shown that the confinement can be up to 50% better than the ITER-98-pby2 H-mode scaling, consistent with the requirements for an ST-based CTF and Demo. In NSTX, CTF-relevant average toroidal beta values {beta}{sub T} of up to 35% with a near unity central {beta}{sub T} have been obtained. NSTX will be exploring advanced regimes where {beta}{sub T} up to 40% can be sustained through active stabilization of resistive wall modes. To date, the most successful technique for non-inductive sustainment in NSTX is the high beta poloidal regime, where discharges with a high non-inductive fraction ({approx}60% bootstrap current+NBI current drive) were sustained over the resistive skin time. Research on radio-frequency (RF) based heating and current drive utilizing high harmonic fast wave and electron Bernstein wave is also pursued on NSTX, PEGASUS, and CDX-U. For non-inductive start-up, the coaxial helicity injection, developed in HIT/HIT-II, has been adopted on NSTX to test the method up to I{sub p} {approx} 500 kA. In parallel, start-up using a RF current drive and only external poloidal field coils are being developed on NSTX. The area of power and particle handling is expected to be challenging because of the higher power density expected in the ST relative to that in conventional aspect-ratio tokamaks. Due to its promise for power and particle handling, liquid lithium is being studied in CDX-U as a potential plasma-facing surface for a fusion reactor.

Hyphendated LC-MS techniques are quickly becoming the standard tool for protemic analyses. For large homogeneous samples, bulk processing methods and capillary injection and separation techniques are suitable. However, for analysis of small or heterogeneous samples, techniques that can manipulate picoliter samples without dilution are required or samples will be lost or corrupted; further, static nanospray-type flowrates are required to maximize SNR. Microchip-level integration of sample injection with separation and mass spectrometry allow small-volume analytes to be processed on chip and immediately injected without dilution for analysis. An on-chip HPLC was fabricated using in situ polymerization of both fixed and mobile polymer monoliths. Integration of the chip with a nanospray MS emitter enables identification of peptides by the use of tandem MS. The chip is capable of analyzing of very small sample volumes (< 200 pl) in short times (< 3 min).

Abstract not provided.

Optically detected magnetic resonance (ODMR) has been performed on Si-doped GaN homoepitaxial layers grown by organometallic chemical vapor deposition on free-standing GaN templates. In addition to intense excitonic bandedge emission with narrow linewidths (<0.4 meV), these films exhibit strong shallow donor-shallow acceptor recombination at 3.27 eV. Most notably, ODMR on this photoluminescence band reveals a highly anisotropic resonance with g{sub {parallel}} = 2.193 {+-} 0.001 and g{sub {perpendicular}} {approx}0 as expected for effective-mass shallow acceptors in wurtzitic GaN from k {center_dot} p theory. This previously elusive result is attributed to the much reduced dislocation density and impurity levels compared to those typically found in the widely investigated Mg-doped GaN heteroepitaxial layers. The possible chemical origin of the shallow acceptors in these homoepitaxial films will be discussed.

Abstract not provided.

Abstract not provided.

Sealed lead acid cells are used in many projects in Sandia National Laboratories Department 2660 Telemetry and Instrumentation systems. The importance of these cells in battery packs for powering electronics to remotely conduct tests is significant. Since many tests are carried out in flight or launched, temperature is a major factor. It is also important that the battery packs are properly charged so that the test is completed before the pack cannot supply sufficient power. Department 2665 conducted research and studies to determine the effects of temperature on cycle time as well as charging techniques to maximize cycle life and cycle times on sealed lead acid cells. The studies proved that both temperature and charging techniques are very important for battery life to support successful field testing and expensive flight and launched tests. This report demonstrates the effects of temperature on cycle time for SLA cells as well as proper charging techniques to get the most life and cycle time out of SLA cells in battery packs.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Intracellular molecular machines synthesize molecules, tear apart others, transport materials, transform energy into different forms, and carry out a host of other coordinated processes. Many molecular processes have been shown to work outside of cells, and the idea of harnessing these molecular machines to build nanostructures is attractive. Two examples are microtubules and motor proteins, which aid cell movement, help determine cell shape and internal structure, and transport vesicles and organelles within the cell. These molecular machines work in a stochastic, noisy fashion: microtubules switch randomly between growing and shrinking in a process known as dynamic instability; motor protein movement along microtubules is randomly interrupted by the motor proteins falling off. A common strategy in attempting to gain control over these highly dynamic, stochastic processes is to eliminate some processes (e.g., work with stabilized microtubules) in order to focus on others (interaction of microtubules with motor proteins). In this paper, we illustrate a different strategy for building nanostructures, which, rather than attempting to control or eliminate some dynamic processes, uses them to advantage in building nanostructures. Specifically, using stochastic agent-based simulations, we show how the natural dynamic instability of microtubules can be harnessed in building nanostructures, and discuss strategies for ensuring that 'unreliable' stochastic processes yield a robust outcome.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Coupling between transient simulation codes of different fidelity can often be performed at the nonlinear solver level, if the time scales of the two codes are similar. A good example is electrical mixed-mode simulation, in which an analog circuit simulator is coupled to a PDE-based semiconductor device simulator. Semiconductor simulation problems, such as single-event upset (SEU), often require the fidelity of a mesh-based device simulator but are only meaningful when dynamically coupled with an external circuit. For such problems a mixed-level simulator is desirable, but the two types of simulation generally have different (somewhat conflicting) numerical requirements. To address these considerations, we have investigated variations of the two-level Newton algorithm, which preserves tight coupling between the circuit and the PDE device, while optimizing the numerics for both. The research was done within Xyce, a massively parallel electronic simulator under development at Sandia National Laboratories.

Abstract not provided.

Abstract not provided.

Abstract not provided.