Publications

This document describes the results of the Comprehensive Test Ban Treaty (CTBT) Infrasound Prototype Development Test and Evaluation (DT&E). During DT&E the infrasound prototype was evaluated against requirements listed in the System Requirements Document (SRD) based on the Conference on Disarmament/Ad Hoc Committee on a Nuclear Test Ban/Working Papers 224 and 283 and the Preparatory Commission specifications as defined in CTBT/PC/II/1/Add.2, Appendix X, Table 5. The evaluation was conducted during a two-day period, August 6-7, 18997. The System Test Plan (STP) defined the plan and methods to test the infrasound prototype. Specific tests that were performed are detailed in the Test Procedures (TP).

The results of the investigation of retention and thermal desorption of hydrogen isotopes of B{sub 4}C coated RGT (a recrystallized graphite with high thermal conductivity, 600 W/mK) after the exposure to high heat flux in the divertor strike point region of DIII-D using the DiMES sample exchange system are reported. It is shown that the material is very promising for plasma facing elements of tokamaks.

Neutron reflection is used to examine the structure of an epoxy near an interface. Variations in both the density and the crosslink density within the interphase region are examined. The density is increased near the interface relative to that in the bulk of the film, but the crosslink density over the same region is reduced relative to that in the bulk of the film. These observations are interpreted via packing of the resin oligamers next to the wall, which leads to an increased density and also inhibits the crosslinking reaction. The effect is more pronounced the more slowly the resin is cured. Significant variations in reflectivity are observed with thermal cycling, which indicate an increase in the size of the interfacial layer of excess toluene. However, data for samples with greater number of thermal cycles are required to determine the relation of this effect to the fracture process.

SEMATECH was established in 1987 for defense and economic reasons to help the U.S. regain a competitive posture in semiconductor manufacturing. For 10 years SEMATECH was jointly funded by the federal government and semiconductor manufacturing companies representing 85 percent of the U.S. semiconductor industry. SEMATECH has spent about 80 percent of these funds on activities intended to produce useful results between 1 and 3 years. Very early in the establishment of SEMATECH, its members determined that their first priority would be to strengthen their U.S. based suppliers of semiconductor manufacturing equipment. This has been the primary thrust of SEMATECH. SEMATECH first held some 30 workshops on a broad set of technical topics to assess the needs and opportunities to help the industry recover. These workshops scoped manufacturing areas where SEMATECH should focus. These early meetings were an early form of what later came to be termed roadmapping. The scope of R&D needs identified in these workshops well exceeded what SEMATECH could hope to accomplish with its $200 million annual budget. Wayne Johnson of Sandia participated in five of these workshops and used the knowledge gained as the basis for proposals later submitted to SEMATECH on behalf of Sandia. In the fall of 1989 the SETEC program was established at Sandia to support SEMATECH. This was initially a funds-in, work-for-others project that was fully funded by SEMATECH. Thus, the early work was entirely focused on SEMATECH`s needs. Later in the program when SEMATECH funds were supplemented by Department of Energy Cooperative Research and Development funds, attention was given to how this project would benefit Sandia`s defense microelectronics program.

This paper presents an analysis of how the US government responded to the concern in the 1980`s that US companies were experiencing problems of competitiveness in international markets. By the mid 1980`s there was great and growing concern throughout the US that US companies were experiencing difficulties in international competition. Pressure on Congress to take action came from constituents seeking jobs and companies that would directly benefit (this usually means receive public money) from programs that Congress might initiate. The fact that most constituent calls to Congress were about job creation was lost in the on-rush of R&D performers seeking funds for their favorite R&D project. In response, Congress created the Advanced Technology Program, the Technology Transfer Initiative, and the Technology Reinvestment Project, expanded the responsibilities of ARPA/DARPA, increased funding for the Small Business Initiative, expanded the Manufacturing Extension Partnership, funded SEMATECH, and increased NSF funding for basic research at universities. Many of these programs were later criticized for being industrial welfare and several were cut-back or stopped. Retrospective analysis shows that few of these programs addressed the root cause of competitiveness difficulties. In fact, by the time most of these programs were in place, US companies were well on their way to correcting their competitiveness problems. In addition, few were relevant to companies` often expressed concerns about workforce training, regulatory costs, and access to foreign markets. Twenty percent reductions in health care costs, regulatory costs, and education costs could annually pump $500 billion into the US economy and make companies operating in the US much more competitive in international markets.

The papers in this Faraday Discussion represent the state-of-the-art in using acoustic devices to measure the properties of thin films and interfaces. Sauerbrey first showed that the mass sensitivity of a quartz crystal could be used to measure the thickness of vacuum-deposited metals. Since then, significant progress has been made in understanding other interaction mechanisms between acoustic devices and contacting media. Bruckenstein and Shay and Kanazawa and Gordon showed that quartz resonators could be operated in a fluid to measure surface mass accumulation and fluid properties. The increased understanding of interactions between acoustic devices and contacting media has allowed new information to be obtained about thin films and interfaces. These closing remarks will summarize the current state of using acoustic techniques to probe thin films and interfaces, describe the progress reported in this Faraday Discussion, and outline some remaining problems. Progress includes new measurement techniques, novel devices, new applications, and improved modeling and data analysis.

Efforts to optimize the design of mechanical systems for preestablished use environments and to extend the durations of use cycles establish a need for in-service health monitoring. Numerous studies have proposed measures of structural response for the identification of structural damage, but few have suggested systematic techniques to guide the decision as to whether or not damage has occurred based on real data. Such techniques are necessary because in field applications the environments in which systems operate and the measurements that characterize system behavior are random. This paper investigates the use of artificial neural networks (ANNs) to identify damage in mechanical systems. Two probabilistic neural networks (PNNs) are developed and used to judge whether or not damage has occurred in a specific mechanical system, based on experimental measurements. The first PNN is a classical type that casts Bayesian decision analysis into an ANN framework; it uses exemplars measured from the undamaged and damaged system to establish whether system response measurements of unknown origin come from the former class (undamaged) or the latter class (damaged). The second PNN establishes the character of the undamaged system in terms of a kernel density estimator of measures of system response; when presented with system response measures of unknown origin, it makes a probabilistic judgment whether or not the data come from the undamaged population. The physical system used to carry out the experiments is an aerospace system component, and the environment used to excite the system is a stationary random vibration. The results of damage identification experiments are presented along with conclusions rating the effectiveness of the approaches.

Many nuclear power plants use instrument and control systems based on analog electronics. The state of the art in process control and instrumentation has advanced to use digital electronics and incorporate advanced technology. This technology includes distributed microprocessors, fiber optics, intelligent systems (neural networks), and advanced displays. The technology is used to optimize processes and enhance the man-machine interface while maintaining control and safety of the processes. Nuclear power plant operators have been hesitant to install this technology because of the cost and uncertainty in the regulatory process. This technology can be directly applied in an operating nuclear power plant provided a surety principle-based {open_quotes}administrator{close_quotes} hardware system is included in parallel with the upgrade Sandia National Laboratories has developed a rigorous approach to High Consequence System Surety (HCSS). This approach addresses the key issues of safety, security, and control while satisfying requirements for reliability and quality. HCSS principles can be applied to nuclear power plants in a manner that allows the off-the-shelf use of process control instrumentation while maintaining a high level of safety and enhancing the plant performance. We propose that an HCSS administrator be constructed as a standardized approach to address regulatory issues. Such an administrator would allow a plant control system to be constructed with commercially available, state-of-the-art equipment and be customized to the needs of the individual plant operator.

Given the complex geometry of most wind turbine blades, structural modeling using the finite element method is generally performed using a unique model for each particular blade analysis. Development time (often considerable) spent creating a model for one blade may not aid in the development of a model for a different blade. In an effort to reduce model development time and increase the usability of advanced finite element analysis capabilities, a new software tool, NuMAD, is being developed.

If there should be an accident involving drainage of all the water from a spent fuel pool, the fuel elements will heat up until the heat produced by radioactive decay is balanced by that removed by natural convection to air, thermal radiation, and other means. If the temperatures become high enough for the cladding or other materials to ignite due to rapid oxidation, then some of the fuel might melt, leading to an undesirable release of radioactive materials. The amount of melting is dependent upon the fuel loading configuration and its age, the oxidation and melting characteristics of the materials, and the potential effectiveness of recovery actions. The authors have developed methods for modeling the pertinent physical phenomena and integrating the results with a probabilistic treatment of the uncertainty distributions. The net result is a set of complementary cumulative distribution functions for the amount of fuel melted.

A freeform fabrication technique for dense ceramics and composites has been developed. The technique requires less than 2 volume percent of organic additives and relies on the principle of layerwise deposition of highly loaded colloidal slurries. Components can be manufactured into complex geometries with thick solid sections as well as with thin-walled sections with high aspect ratios. Process feasibility and quality is dependent on the processing parameters of solids loading, slurry rheology, deposition rate, and drying rate. These interrelated parameters must be controlled so that sintering defects are prevented and shape tolerance is maintained. A review of this freeform fabrication technique, called robocasting, will be discussed for fabrication of aluminum oxide parts. Recent developments for a finite element analysis technique for modeling the drying process will also be presented.

Using molecular beam epitaxy (MBE) and lattice engineering techniques, the feasibility of combining photonic devices applicable to the 1.3 to 1.55 {micro}m wavelength range and monolithic microwave (or mm-wave) integrated circuits (MMICs) on GaAs is demonstrated. A key factor in the MBE growth is incorporation of an InGaAs active layer having an indium arsenide mole fraction of 0.35 or greater and its lattice compatibility with the underlying semi-insulating GaAs substrate. The InGaAs layer used for the photonic devices, can also serve as the active channel for the high electron mobility transistors (HEMTs) for application in MMICs. Several examples of active and passive photonic devices grown by MBE are presented including an optical ridge waveguide, and a photodetector for detection of light in the 1.3 {micro}m range. The material structure includes a 3-layer AlGaAs/GaAs/AlGaAs optical waveguide and a thin InGaAs absorbing layer situated directly above the optical waveguide. Metal-semiconductor-metal (MSM) photodetectors are formed on the top surface of the InGaAs layer for collection of the photo-induced carriers. The optical ridge waveguide is designed for lateral incidence of the light to enhance the MSM photodetector responsivity. Initial measurements on the optical waveguide and photodetector are presented.

The purpose of this project is to develop and extend the electron beam joining process to applications related to Mo/Al{sub 2}O{sub 3} cermets for neutron tube fabrication, glass seals for flat panel displays, and ceramics for structural applications. The key issue is the identification of the allowable operating ranges that produce thermal conditions favorable to robust joining and sealing. High strength, hermetic braze joints between ceramic components have been produced using high energy electron beams. With a penetration depth into a typical ceramic of {approximately} 1 cm for a 10 MeV electron beam, this method provides the capability for rapid, transient brazing operations where temperature control of heat sensitive components is essential. The method deposits energy directly into a buried joint, allowing otherwise inaccessible interfaces to be brazed. The combination of transient heating, with higher thermal conductivity, lower heat capacity, and lower melting temperature of braze metals relative to the ceramic materials, enables a pulsed high power beam to melt a braze metal without producing excessive ceramic temperatures. The authors have demonstrated the feasibility of this process related to ceramic coupons a well as ceramic and glass tubes and cylindrical shapes. The transient thermal response was predicted, using as input the energy absorption predicted from the coupled electron-photon and thermal transport analysis. The joining experiments were conducted with an RF linear accelerator at 10--13 MV. Joining experiments have provided high strength joints between alumina and alumina and between alumina and cermet joints in cylindrical geometry. These joints provided good hermetic seals.

Intense pulsed high-power ion beams have been demonstrated to produce enhanced surface properties by changes in microstructure caused by rapid heating and cooling of the surface. Additional improvements can be effected by the mixing of a previously deposited thin-film layer (surface alloying or ion beam mixing) into any number of substrate materials. The authors have conducted surface treatment and alloying experiments with Al, Fe, and Ti-based metals on the RHEPP-1 accelerator (0.8 MV, 20 W, 80 ns FHWM, up to 1 Hz repetition rate) at Sandia National Laboratories. Ions are generated by the MAP gas-breakdown active anode, which can yield a number of different beam species including H, N, and Xe, depending upon the injected gas. Enhanced hardness and wear resistance have been produced by treatment of 440C stainless steel, and by the mixing of Pt into Ti-6Al-4V alloy. Mixing of a thin-film Hf layer into Al 6061-T6 alloy (Al-1.0Mg-0.6Si) has improved its corrosion resistance by as much as four orders of magnitude in electrochemical testing, compared with untreated and uncoated Al6061. Experiments are ongoing to further understand the microstructural basis for these surface improvements.

The Hardware Design Document (HDD) describes the various hardware components used in the Comprehensive Test Ban Treaty (CTBT) Infrasound Prototype and their interrelationships. It divides the infrasound prototype into hardware configurations items (HWCIs). The HDD uses techniques such as block diagrams and parts lists to present this information. The level of detail provided in the following sections should be sufficient to allow potential users to procure and install the infrasound system. Infrasonic monitoring is a low cost, robust, and effective technology for detecting atmospheric explosions. Low frequencies from explosion signals propagate to long ranges (few thousand kilometers) where they can be detected with an array of sensors.

In this paper we describe a new method for creating three-dimensional images using pairs of synthetic aperture radar (SAR) images obtained from a unique collection geometry. This collection mode involves synthetic apertures that have a common center. In this sense the illumination directions for the two SAR images are the same, while the slant planes are at different spatial orientations. The slant plane orientations give rise to cross-range layover (fore-shortening) components in the two images that are of equal magnitude but opposite directions. This differential cross-range layover is therefore proportional to the elevation of a given target, which is completely analogous to the situation in stereo optical imaging, wherein two film planes (corresponding to the two slant planes) result in elevation-dependent parallax. Because the two SAR collections are coherent in this particular collection mode, the images have the same speckle patterns throughout. As a result, the images may be placed into stereo correspondence via calculation of correlations between micro-patches of the complex image data. The resulting computed digital stereo elevation map can be quite accurate. Alternatively, an analog anaglyph can be displayed for 3-D viewing, avoiding the necessity of the stereo correspondence calculation.

Chromium-contaminated soil is a common environmental problem in the United States as a result of numerous industrial processes involving chromium. Hexavalent chromium [Cr(VI)] is the species of most concern because of its toxicity and mobility in groundwater. One method of diminishing the environmental impact of chromium is to reduce it to a trivalent oxidation state [Cr(III)], in which it is relatively insoluble and nontoxic. This study investigated a stabilization and solidification process to minimize the chromium concentration in the Toxicity Characteristic Leaching Procedure (TCLP) extract and to produce a solidified waste form with a compressive strength in the range of 150 to 300 pounds per square inch (psi). To minimize the chromium in the TCLP extract, the chromium had to be reduced to the trivalent oxidation state. The average used in this study was an alluvium contaminated with chromic and sulfuric acid solutions. The chromium concentration in the in the in situ soil was 1212 milligrams per kilogram (mg/kg) total chromium and 275 mg/kg Cr(VI). The effectiveness of iron, ferrous sulfate to reduce Cr(VI) was tested in batch experiments.

The temperature, curing, and filler dependencies of the viscosities of common epoxies used at Sandia encapsulants are presented along with examples of useful applications.

Butyl rubber, unfortunately, has pronounced nonlinear viscoelastic behavior, which may be modelled by a separable KBKZ formalism. While these effects seem to have minimal impact on accelerated sealing force measurements, they do severely impact compression set tests. Therefore, a new test is suggested for evaluating field-return o-rings which is free from such confounding effects.

This report describes the results of a Sandia-funded laboratory-directed research and development project titled {open_quotes}Integrated and Robust Security Infrastructure{close_quotes} (IRSI). IRSI was to provide a broad range of commercial-grade security services to any software application. IRSI has two primary goals: application transparency and manageable public key infrastructure. IRSI must provide its security services to any application without the need to modify the application to invoke the security services. Public key mechanisms are well suited for a network with many end users and systems. There are many issues that make it difficult to deploy and manage a public key infrastructure. IRSI addressed some of these issues to create a more manageable public key infrastructure.

This report summarizes measured performance of residential geothermal heat pumps (GHP`s) that were installed in family housing units at Ft. Hood, Texas and at Selfridge Air National Guard base in Michigan. These units were built as part of a joint Department of Defense/Department of Energy program to evaluate the energy savings potential of GHP`s installed at military facilities. At the Ft. Hood site, the GHP performance was compared to conventional forced air electric air conditioning and natural gas heating. At Selfridge, the homes under test were originally equipped with electric baseboard heat and no air conditioning. Installation of the GHP systems at both sites was straightforward but more problems and costs were incurred at Selfridge because of the need to install ductwork in the homes. The GHP`s at both sites produced impressive energy savings. These savings approached 40% for most of the homes tested. The low cost of energy on these bases relative to the incremental cost of the GHP conversions precludes rapid payback of the GHP`s from energy savings alone. Estimates based on simple payback (no inflation and no interest on capital) indicated payback times from 15 to 20 years at both sites. These payback times may be reduced by considering the additional savings possible due to reduced maintenance costs. Results are summarized in terms of 15 minute, hourly, monthly, and annual performance parameters. The results indicate that all the systems were working properly but several design shortcomings were identified. Recommendations are made for improvements in future installations at both sites.

Results from simulations of the impact and penetration of tungsten alloy rods into thick rolled armor plates are presented. The calculations were performed with the CTH and ALEGRA computer codes using the DOE massively parallel TFLOPS computer co-developed by Sandia National Laboratory and Intel Corporation. Comparisons with experimental results are presented. Agreement of the two codes with each other and with the empirical results for penetration channel depth and radius is very close. Other shock physics and penetration features are also compared to simulation results.

Analytical models of wind turbine blades have many uncertainties, particularly with composite construction where material properties and cross-sectional dimension may not be known or precisely controllable. In this paper the authors demonstrate how modal testing can be used to estimate important material parameters and to update and improve a finite-element (FE) model of a prototype wind turbine blade. An example of prototype blade is used here to demonstrate how model parameters can be identified. The starting point is an FE model of the blade, using best estimates for the material constants. Frequencies of the lowest fourteen modes are used as the basis for comparisons between model predictions and test data. Natural frequencies and mode shapes calculated with the FE model are used in an optimal test design code to select instrumentation (accelerometer) and excitation locations that capture all the desired mode shapes. The FE model is also used to calculate sensitivities of the modal frequencies to each of the uncertain material parameters. These parameters are estimated, or updated, using a weighted least-squares technique to minimize the difference between test frequencies and predicted results. Updated material properties are determined for axial, transverse, and shear moduli in two separate regions of the blade cross section: in the central box, and in the leading and trailing panels. Static FE analyses are then conducted with the updated material parameters to determine changes in effective beam stiffness and buckling loads.

Natural attenuation is increasingly applied to remediate contaminated soils and ground waters. Roughly 25% of Superfund groundwater remedies in 1995 involved some type of monitored natural attenuation, compared to almost none 5 years ago. Remediation by natural attenuation (RNA) requires clear evidence that contaminant levels are decreasing sufficiently over time, a defensible explanation of the attenuation mechanism, long-term monitoring, and a contingency plan at the very least. Although the primary focus of implementation has to date been the biodegradation of organic contaminants, there is a wealth of scientific evidence that natural processes reduce the bioavailability of contaminant metals and radionuclides. Natural attenuation of metals and radionuclides is likely to revolve around sorption, solubility, biologic uptake and dilution controls over contaminant availability. Some of these processes can be applied to actively remediate sites. Others, such as phytoremediation, are likely to be ineffective. RNA of metals and radionuclides is likely to require specialized site characterization to construct contaminant and site-specific conceptual models of contaminant behavior. Ideally, conceptual models should be refined such that contaminant attenuation can be confidently predicted into the future. The technical approach to RNA of metals and radionuclides is explored here.

During July--November, 1995, Sandia National Laboratories, in cooperation with CE Exploration, drilled a 5,360 feet exploratory slimhole (3.895 inch diameter) in the Newberry Known Geothermal Resource Area (KGRA) near Bend, Oregon. This well was part of Sandia`s program to evaluate slimholes as a geothermal exploration tool. During and after drilling the authors performed numerous temperature logs, and at the completion of drilling attempted to perform injection tests. In addition to these measurements, the well`s data set includes: over 4,000 feet of continuous core (with detailed log); daily drilling reports from Sandia and from drilling contractor personnel; daily drilling fluid record; and comparative data from other wells drilled in the Newberry KGRA. This report contains: (1) a narrative account of the drilling and testing, (2) a description of equipment used, (3) a brief geologic description of the formation drilled, (4) a summary and preliminary interpretation of the data, and (5) recommendations for future work.