Publications

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

We have completed a series of small-scale cook-off experiments of ammonium nitrate (AN) prills in our Sandia Instrumented Thermal Ignition test at nominal packing densities of about 0.8 g/cm3. We increased the boundary temperature of our aluminum confinement cylinder from room temperature to a prescribed set-point temperature in 10 min. Our set-point temperature ranged from 508 to 538 K. The external temperature of the confining cylinder was held at the set-point temperature until ignition. We used type K thermocouples to measure temperatures associated with several polymorphic phase changes as well as melting and boiling. As the AN boiled, our thermocouples were destroyed by corrosion, which may have been caused by reaction of hot nitric acid (HNO3) with nickel to form nickel nitrate, Ni(NO3)2. Videos of the corroding thermocouples showed a green solution that was similar to the color of Ni(NO3)2. We found that ignition was imminent as the AN boiling point was exceeded. Ignition of the AN prills was modeled by solving the energy equation with an energy source due to desorption of moisture and decomposition of AN to form equilibrium products. A Boussinesq approximation was used in conjunction with the momentum equation to model flow of the liquid AN. We found that the prediction of ignition was not sensitive to small perturbations in the latent enthalpies.

We have used several configurations of the Sandia Instrumented Thermal Ignition (SITI) experiment to develop a pressure-dependent, four-step ignition model for a plastic bonded explosive (PBX 9407) consisting of 94 wt.% RDX (hexahydro-1,3,5-trinitro-1,3,5-triazine), and a 6 wt.% VCTFE binder (vinyl chloride/chlorotrifluoroethylene copolymer). The four steps include desorption of water, decomposition of RDX to form equilibrium products, pressure-dependent decomposition of RDX forming equilibrium products, and decomposition of the binder to form hydrogen chloride and a nonvolatile residue (NVR). We address drying, binder decomposition, and decomposition of the RDX component from the pristine state through the melt and into ignition. We used Latin Hypercube Sampling (LHS) of the parameters to determine the sensitivity of the model to variation in the parameters. We also successfully validated the model using one-dimensional time-to-explosion (ODTX and P-ODTX) data from a different laboratory. Our SITI test matrix included 1) different densities ranging from 0.7 to 1.63 g/cm3, 2) free gas volumes ranging from 1.2 to 38 cm3, and 3) boundary temperatures ranging from 170 to 190 °C. We measured internal temperatures using embedded thermocouples at various radial locations as well as pressure using tubing that was connected from the free gas volume (ullage) to a pressure gauge. We also measured gas flow from our vented experiments. A borescope was included to obtain in situ video during some SITI experiments. We observed significant changes in the explosive volume prior to ignition. Our model, in conjunction with data observations, imply that internal accumulation of decomposition gases in high density PBX 9407 (90% of the theoretical maximum density) can contribute to significant strain whether or not the experiment is vented or sealed.

Abstract not provided.

Abstract not provided.

Abstract not provided.

We combined the miniature cylinder expansion test (Mini-Cylex), with the Disk Acceleration Test (DAX) using Type K copper, Picatinny Liquid Explosive, and photonic Doppler velocimetry. We estimated the CJ state using plate reverberation methods at the test cap. We extracted velocities at 2, 7, and 10 volume expansions to fit Jones-Wilkins-Lee Equation of State and estimated Gurney velocity at the tube wall. The test also provides an additional method to estimate reaction products Hugoniot through knowledge of the copper test cap. Our experiments and simulations are within expected uncertainty. The test and the analysis effectively reduce costs while keeping or increasing fidelity.

In previous studies, we found that the nitroplasticizer in the HMX-based explosive PBX 9501 played a crucial role in cookoff, especially when predicting response in larger systems. We have recently completed experiments with a similar explosive, LX-14, that has a relatively nonreactive binder. We expected the ignition times for LX-14 to be longer than PBX 9501 since PBX 9501 has a more reactive binder. However, our experiments show the opposite trend. This paradox can be explained by retention of reactive gases within the interior of LX-14 by the higher strength binder resulting in faster ignition times. In contrast, the binder in PBX 9501 melts at low temperatures and does not retain decomposition gases as well as the LX- 14 binder. Retention of reactive gases in LX-14 may also explain the more violent response in oblique impact tests when compared to PBX 9501.

A diffusion-limited reaction model was calibrated for Al/Pt multilayers ignited on oxidized silicon, sapphire, and tungsten substrates, as well as for some Al/Pt multilayers ignited as free-standing foils. The model was implemented in a finite element analysis code and used to match experimental burn front velocity data collected from several years of testing at Sandia National Laboratories. Moreover, both the simulations and experiments reveal well-defined quench limits in the total Al + Pt layer (i.e., bilayer) thickness. At these limits, the heat generated from atomic diffusion is insufficient to support a self-propagating wave front on top of the substrates. Quench limits for reactive multilayers are seldom reported and are found to depend on the thermal properties of the individual layers. Here, the diffusion-limited reaction model is generalized to allow for temperature- and composition-dependent material properties, phase change, and anisotropic thermal conductivity. Utilizing this increase in model fidelity, excellent overall agreement is shown between the simulations and experimental results with a single calibrated parameter set. However, the burn front velocities of Al/Pt multilayers ignited on tungsten substrates are over-predicted. Possible sources of error are discussed and a higher activation energy (from 41.9 kJ/mol.at. to 47.5 kJ/mol.at.) is shown to bring the simulations into agreement with the velocity data observed on tungsten substrates. This higher activation energy suggests an inhibited diffusion mechanism present at lower heating rates.

In this study, we have made reasonable cookoff predictions of large-scale explosive systems by using pressure-dependent kinetics determined from small-scale experiments. Scale-up is determined by properly accounting for pressure generated from gaseous decomposition products and the volume that these reactive gases occupy, e.g. trapped within the explosive, the system, or vented. The pressure effect on the decomposition rates has been determined for different explosives by using both vented and sealed experiments at low densities. Low-density explosives are usually permeable to decomposition gases and can be used in both vented and sealed configurations to determine pressure-dependent reaction rates. In contrast, explosives that are near the theoretical maximum density (TMD) are not as permeable to decomposition gases, and pressure-dependent kinetics are difficult to determine. Ignition in explosives at high densities can be predicted by using pressure-dependent rates determined from the low-density experiments as long as gas volume changes associated with bulk thermal expansion are also considered. In the current work, cookoff of the plastic-bonded explosives PBX 9501 and PBX 9502 is reviewed and new experimental work on LX-14 is presented. Reactive gases are formed inside these heated explosives causing large internal pressures. The pressure is released differently for each of these explosives. For PBX 9501, permeability is increased and internal pressure is relieved as the nitroplasticizer melts and decomposes. Internal pressure in PBX 9502 is relieved as the material is damaged by cracks and spalling. For LX-14, internal pressure is not relieved until the explosive thermally ignites. The current paper is an extension of work presented at the 26th ICDERS symposium [1].

Abstract not provided.

Abstract not provided.

Abstract not provided.

Al/Pt nanolaminates with a bilayer thickness (tb, width of an Al/Pt pair-layer) of 164 nm were irradiated with single laser pulses with durations of 10 ms and 0.5 ms at 189 W/cm2 and 1189 W/cm2, respectively. The time to ignition was measured for each pulse, and shorter ignition times were observed for the higher power/shorter pulse width. Videographic images of the irradiated area shortly after ignition show a non-uniform radial brightness for the longer pulse, while the shorter pulse shows uniform brightness. A diffusion-limited single step reaction mechanism was implemented in a finite element package to model the progress from reactants to products at both pulse widths. The model captures well both the observed ignition delay and qualitative observations regarding the non-uniform radial temperature.

Abstract not provided.

Abstract not provided.

Abstract not provided.

We have previously developed a PBX 9501 cookoff model for the plastic bonded explosive PBX 9501 consisting of 95 wt% octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazoncine (HMX), 2.5 wt% Estane® 5703 (a polyurethane thermoplastic), and 2.5 wt% of a nitroplasticizer (NP): BDNPA/F, a 50/50 wt% eutectic mixture bis(2,2-dinitropropyl)-acetal (BDNPA) and bis(2,2-dinitropropyl)-formal (BDNPF). This fivestep model includes desorption of water, decomposition of the NP to form NO₂, reaction of the NO₂ with Estane and HMX, and decomposition of HMX [1]. This model has been successfully validated with data from six laboratories with scales ranging from 2 g to more than 2.5 kg of explosive. We have determined, that the PBX 9501 model can be used to predict cookoff of other plastic bonded explosives containing HMX and an inert binder, such as LX-04 consisting of 85 wt% HMX and 15 wt% Viton A (vinylidine fluoride/hexafluoropropylene copolymer), LX-07 (90 wt% HMX and 10 wt% Viton A), LX- 10-0 (95 wt% HMX and 5 wt% Viton A), and LX-14 consisting of 95.5 wt % HMX and 4.5 wt% Estane® 5702-F1 (a polyurethane thermoplastic). Normally our cookoff models are verified using Sandia’s Instrumented Thermal Initiation (SITI) experiment. However, SITI data for LX-04, LX-07, LX-10-0, and LX-14 are not available at pressed density; although, some molding powder SITI data on LX-10-0 and LX-14 exists. Tarver and Tran [2] provide some one-dimensional time-to-explosion (ODTX) data for these explosives. The applicability of the PBX 9501 model to LX-04, LX-07, LX-10-0, AND LX-14 was made using this ODTX data [2]. The PBX 9501 model is applied to these other explosives by accounting for the correct amount of HMX in the explosive and limiting the NP reaction. We have found the PBX 9501 model to be useful for predicting the response of these PBXs to abnormal thermal environments such as fire.

We previously developed a PETN thermal decomposition model that accurately predicts thermal ignition and detonator failure [1]. This model was originally developed for CALORE [2] and required several complex user subroutines. Recently, a simplified version of the PETN decomposition model was implemented into ARIA [3] using a general chemistry framework without need for user subroutines. Detonator failure was also predicted with this new model using ENCORE. The model was simplified by 1) basing the model on moles rather than mass, 2) simplifying the thermal conductivity model, and 3) implementing ARIA’s new phase change model. This memo briefly describes the model, implementation, and validation.

Abstract not provided.

We have used a modified version of the Sandia Instrumented Thermal Ignition (SITI) experiment to develop a pressure-dependent, five-step ignition model for a plastic bonded explosive (PBX 9501) consisting of 95 wt% octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazoncine (HMX), 2.5 wt% Estane® 5703 (a polyurethane thermoplastic), and 2.5 wt% of a nitroplasticizer (NP): BDNPA/F, a 50/50 wt% eutectic mixture bis(2,2-dinitropropyl)-acetal (BDNPA) and bis(2,2-dinitropropyl)-formal (BDNPF). The five steps include desorption of water, decomposition of the NP to form NO2, reaction of the NO2 with Estane® and HMX, and decomposition of HMX. The model was fit using our experiments and successfully validated with experiments from five other laboratories with scales ranging from about 2 g to more than 2.5 kg of PBX. Our experimental variables included density, confinement, free gas volume, and temperature. We measured internal temperatures, confinement pressure, and ignition time. In some of our experiments, we used a borescope to visually observe the decomposing PBX. Our observations included the endothermic β–δ phase change of the HMX, a small exothermic temperature excursion in low-density unconfined experiments, and runaway ignition. We hypothesize that the temperature excursion in these low density experiments was associated with the NP decomposing exothermically within the PBX sample. This reactant-limited temperature excursion was not observed with our thermocouples in the high-density experiments. For these experiments, we believe the binder diffused to the edges of our high density samples and decomposed next to the highly conductive wall as confirmed by our borescope images.

Abstract not provided.