Publications

The near field surrounding buried waste in the proposed high level nuclear waste repository in Yucca Mountain, Nye County, Nevada, is a region where strongly heat driven processes can exist. These strongly heat driven processes further complicate an already very difficult problem, i.e,. predicting groundwater flow and chemical transport through unsaturated fractured, heterogeneous porous media. The coupling between fluid flow and heat emanation is central to understanding these strongly heat driven processes. Although it is important that all of couplings be investigated, the intent of this paper is to discuss the mathematical models and associated computer codes that can be used in investigating the coupled heat emanation and fluid flow in unsaturated porous media. The information in this paper should be useful to those studying these phenomena, validating these models, or investigating the coupling of fluid flow and heat emanation with the other phenomena. The codes implementing these models are commonly referred to as nonisothermal two-phase flow codes. 5 refs., 4 tabs.

Low pressure (200 Torr) metalorganic chemical vapor deposition (MOCVD) of InSb has been examined through variation of the Column III (TMIn) and Column V (TMSb or TESb) precursor partial pressures. The use of lower growth pressure significantly enhanced the range of allowable Column III Column V partial pressures in which specular morphology InSb could be obtained without the formation of In droplets or Sb crystals. In addition, a 70% improvement in the average hole mobility was obtained, compared to InSb grown in the same reactor at atmospheric pressure. SIMS analysis revealed that Si at the substrate/epitaxial layer interface is an important impurity that may contribute to degradation of the mobility. Substitution of TESb for TMSb did not result in any improvement in the purity of the InSb. 6 refs.

The tungsten subfluoride mechanism as well as other proposed mechanisms of selectivity loss are reviewed. To further demonstrate the viability of the tungsten subfluoride mechanism, we have extended the measurement of the tungsten subfluoride production rate down to 450{degree}C. We also report results from some preliminary experiments designed to identify the selectivity loss mechanism when elemental silicon is available for reaction. Comments regarding the origins of the insulator effect and selectivity loss for silane reduction are offered. 23 refs., 2 figs.

The long length and relatively small cross sectional area of the robotic arms envisioned for use inside of the underground nuclear waste storage tanks will require the control of flexible structures. This will become an important problem in the characterization and remediation of these tanks. We are developing control strategies to actively damp residual vibrations in flexible robotic arms caused by high speed motion and abrupt external forces. A planar, two-link flexible arm is currently being used to test these control strategies. In this paper, two methods of control are discussed. The first is a minimum-time control approach which utilizes a finite element model and and optimization program. These tools plan the motor torque profiles necessary for the tip of the arm to move along a straight line, in minimum time, within the motors' torque constraints, and end in a quiescent state. To account for modeling errors in the finite element model, errors in joint angles, velocities, and link curvatures are added to the optimal torque trajectory. Linear quadratic Gaussian (LQG) regulatory design theory is used to determine the feedback gains. The second method of control is a teleoperated joystick controller which uses an input shaping technique to alter the commands of the joystick so as to reduce the residual vibration of the fundamental modes. Approximating the system as linear, the natural frequency and damping ratio are estimated on-line for the complete system, which includes the structure plus a lower level proportional derivative controller. An input shaping filter is determined from the estimated natural frequency, estimated damping ratio, and the desired transfer function of the system. 11 reps., 9 figs.

The concept of solar driven chemical reactions in a commercial-scale volumetric receiver/reactor on a parabolic concentrator was successfully demonstrated in the CAtalytically Enhanced Solar Absorption Receiver (CAESAR) test. Solar reforming of methane (CH{sub 4}) with carbon dioxide (CO{sub 2}) was achieved in a 64-cm diameter direct absorption reactor on a parabolic dish capable of 150 kW solar power. The reactor was a catalytic volumetric absorber consisting of a multi-layered, porous alumina foam disk coated with rhodium (Rh) catalyst. The system was operated during both steady-state and solar transient (cloud passage) conditions. The total solar power absorbed reached values up to 97 kW and the maximum methane conversion was 70%. Receiver thermal efficiencies ranged up to 85% and chemical efficiencies peaked at 54%. The absorber performed satisfactorily in promoting the reforming reaction during the tests without carbon formation. However, problems of cracking and degradation of the porous matrix, nonuniform dispersion of the Rh through the absorber, and catalyst deactivation due to sintering and possible encapsulation, must be resolved to achieve long-term operation and eventual commercialization. 17 refs., 11 figs., 1 tab.

We have performed MD simulations of adhesive phenomena, on an atomic scale, between metals possessing both smooth and stepped-surfaces. Studies of adhesion between identical metals, consisting of either Au, Cu, or Ni, with (001) or (111) orientations, reveal the existence of adhesive avalanches as the bodies are brought to within a critical separation ({approximately}2 {angstrom}). That is, as the surfaces approach one another, one or both surface layers becomes unstable, and abruptly moves toward the other. This signals a transition from an initial system with two distinct surfaces to one possessing no identifiable surfaces. The presence of adhesive avalanches will pose difficulties in determining adhesive forces and energies by means of atomic force microscopy at sub-nanometer separations of probe tip and sample surface. 7 refs., 3 figs.

The use of NUREG-1150 and similar Probabilistic Risk Assessments in NRC and industry risk management programs is discussed. Risk management'' is more comprehensive than the commonly used term accident management.'' Accident management includes strategies to prevent vessel breach, mitigate radionuclide releases from the reactor coolant system, and mitigate radionuclide releases to the environment. Risk management also addresses prevention of accident initiators, prevention of core damage, and implementation of effective emergency response procedures. The methods and results produced in NUREG-1150 provide a framework within which current risk management strategies can be evaluated, and future risk management programs can be developed and assessed. Examples of the use of the NUREG-1150 framework for identifying and evaluating risk management options are presented. All phases of risk management are discussed, with particular attention given to the early phases of accidents. Plans and methods for evaluating accident management strategies that have been identified in the NRC accident management program are discussed. 2 refs., 3 figs.

A new interfacial force microscope capable of measuring the forces between two surfaces over the entire range of surface separations, up to contact, has been developed. The design is centered around a differential capacitance displacement sensor where the common capacitor plate is supported by torsion bars. A force-feedback control system balances the interfacial forces at the sensor, maintaining the common capacitor plate at its rest position. This control eliminates the instability which occurs with the conventional cantilever-based force sensors when the attractive force gradient exceeds the mechanical stiffness of the cantilever. The ability to measure interfacial forces at surface separations smaller than this instability point using the feedback control is demonstrated. 11 refs., 3 figs.

The lowest excited electronic state of molecular oxygen, singlet oxygen ({sup 1}{Delta}{sub g}0{sub 2}), can be produced in solid organic polymers by a variety of different methods. Once produced, singlet oxygen will return to the ground triplet state by two pathways, radiative (phosphorescence) and non-radiative decay. Although the quantum efficiency of phosphorescence is small ({minus}10{sup {minus}5}), singlet oxygen can be detected by its emission at 1270 mn in both steady-state and time-resolved experiments. The phosphorescence of singlet oxygen can be used to characterize many properties of a solid organic polymer. 2 refs., 5 figs.

We review our work on multi component polymeric nonlinear optical materials. These materials consist of nonlinear optical molecules incorporated in a polymeric host. A cross-linked triazine polymer incorporating a dicyanovinyl terminated azo dye was found to be relatively stable at 85{degree} and posses an electro-optic coefficient of 11pm/V. We have also observed the zero dispersion condition in a new anomalous dispersion dye for phase matched second harmonic generation, and expect efficient conversion to the blue. A squarylium dye, ISQ, has been found to posses a large third order nonlinearity, and may display two-level behavior. 24 refs., 11 figs.

An improved standard total-dose test method is described to qualify electronics for a low-dose radiation environment typical of space systems. The method consists of {sup 60}Co irradiation at a dose rate of 1--3 Gy(Si)/s (100--300 rad(Si)/s) and a subsequent 373 K (100{degree}C) bake. New initiatives in radiation hardness assurance are also briefly discussed, including the Qualified Manufacturers List (QML) test methodology and the possible use of 1/f noise measurements as a nondestructive screen for oxide-trap charge related failure. 8 refs.

A two-stage data compression technique that provides for exact, bit-for-bit recovery is described. The first stage is a modified form of conventional linear prediction which generates an error or residue sequence in such a way that exact reconstruction of the original data sequence can be accomplished with a simple recovery algorithm. The second stage is bi-level sequence coding. Even though the residue sequence from the first stage is essential white and Gaussian with seismic or other similar waveform data, bi-level sequence coding will generally provide further compression. The complete technique is described briefly in this summary, and examples of its performance are presented. A full paper on the algorithm is available from the author. 12 refs., 2 figs., 2 tabs.

We have synthesized a new tool, a lasing phase diagram, for designing high efficiency surface-emitting laser resonators and have demonstrated its usefulness by fabricating and operating many different laser resonators. 4 refs., 4 figs.

ULSI manufacturing technologies have resulted in the development of Ultra-Pure Processing (UPP) capabilities for the world-wide semiconductor industry. The primary goal of Ultra Pure Processing is the elimination of extraneous contaminants, both gaseous and particulate, from the wafer process environment. This calls for a comprehensive approach to the design, operation, and maintenance of semiconductor process equipment. Through UPP one may reduce the number of uncontrolled variables within a system enhancing implementation of Statistical Process Control on the process environment within the tool (in situ). Greater control over the process environment translates into increased product quality, manufacturability, throughput and yield. Instituting UPP requires the capability of monitoring contaminants in the process environment a well as a systematic approach to isolating and eliminating contamination sources. Ultra Pure Processing can result from a Contamination Reduction Program. Presented here are the results from a Contamination Reduction Program performed on a state-of-the-art vertical thermal process reactor (VTR). 8 figs., 5 tabs.

The nuclear industry uses sensitive or classified parts and material that must be protected and accounted for. We believe there is a need for an automated system that can help protect and inventory these parts and material. In response to this need Sandia National Laboratories Division 5245 is developing a personnel and material tracking system named PAMTRAK to safeguard sensitive parts and material at selected Department of Energy facilities. This paper describes the project's background, design goals and features.

Sandia National Laboratories has developed a variety of alarm communication and display systems for a broad spectrum of users. This paper will briefly describe the latest systems developed for the Department of Energy (DOE), the Department of Defense (DoD), and the Department of State (DOS) applications. Applications covered will vary from relatively small facilities to large complex sites. Ongoing system developments will also be discussed. The concluding section will summarize the practical, implementable state-of-the-art features available in new systems. 6 figs.

The mechanical behavior of microcellular open-cell foams prepared by a thermally induced phase separation process are investigated. The foams studied were prepared from isotactic polystyrene, polyacrylonitrile, and poly(4-methyl-1-pentene) (rigid foams), and polyurethane and Lycra (elastomeric foams). Their densities were in the range 0.04--0.27 g/cm3. Conventional polystyrene foams were used for comparison. The moduli and collapse stresses of these foams were measured in compression and compared with the current constitutive laws which relate mechanical properties to densities. A reinforcement technique based on the in-situ precipitation of silica was used to improve the mechanical properties. 13 refs., 4 figs., 3 tabs.

Ion implantation has been shown to produce unique improvements in the properties of a wide range of materials. This technology has been extensively used for doping of semiconductors, where the required doses and implantation depths are relatively modest and readily achieved with commercial implanters. Other applications of ion implantation currently being pursued at a commercial level include the synthesis of buried second-phase layers in Si and the improvement of metal surface properties such as hardness, friction, wear rate, and corrosion. However, these applications have been severely constrained by the costs of treating large surface areas with the high ion doses required, and by the need to produce modified layers thicker than the range of the sub-MeV ions available from presently available commercial high-flux ion implanters. It therefore seems worthwhile to consider whether pulsed ion accelerators may offer advantages for such applications by providing high ion fluxes at MeV energies. The previously reported applications of pulsed accelerators to materials modification have used sub-MeV ion energies. The purpose of this article is to being these considerations the perspective of materials scientists who use ion implantation. We comment on needed extensions in implantation capabilities while leaving to others the question of whether these needs can be met with pulsed-beam technology. Further, in order to illustrate the kinds of beneficial materials modifications that can be achieved with implantation, we provide examples from recent work at Sandia National Laboratories, where large improvements have been realized in the tribological properties and strengths of Fe and A{ell} alloys. 10 refs., 6 figs.

The natural language technique was just one of many approaches to information system design in 1987. The success of this approach convinced management of the viability of this new'' approach. A group was created to use natural language in information system specifications and designs. Two of the projects undertaken by this group will be reviewed. The first is a quality database that allows for the management of the process that certifies production capabilities for major weapon components and the second tracks command and control status of weapons. A third external project involving nuclear disarmament will also be discussed.

The United States Department of Energy (DOE) plans to use the Waste Isolation Pilot plant (WIPP) in southeastern New Mexico for disposal of transuranic wastes generated by defense programs. The DOE must first demonstrate compliance with the Environmental Protection Agency's (EPA) Environmental Standards for the Management and Disposal of Spent Nuclear Fuel, High-Level and Transuranic Radioactive Wastes (40 CFR Part 191) hereafter called the Standard. The Standard was vacated by a Federal Court of Appeals in 1987 and is undergoing revision; by agreement with the State of New Mexico the DOE will continue to evaluate repository performance with respect to the Standard as first promulgated until a new version is available. This paper reviews the results of a 1989 preliminary demonstration of the performance-assessment methodology that will be used by the WIPP project ultimately to assess compliance with the Standard. The report also describes conceptual and numerical improvements in the performance-assessment methodology made during 1990, and summarizes the progress made toward achieving the probabilistic assessment of repository performance required for regulatory compliance. 13 refs., 4 figs.

Low-density, microcellular polymer foams have numerous applications as structural supports in high-energy physics experiments, in catalysis, ion exchange, and filtration, and for a variety of biomedical uses. A versatile method to prepare such foams is by thermally-induced phase separation (TIPS) of polymer solutions. Demixed solutions can be transformed into a foam by freezing the demixed solution and removing the solvent by freeze-drying. The morphology of these foams is determined by the the thermodynamics and kinetics of phase separation. A model of both the early and late stage structure development for demixed polymer solutions will be presented. For semi-crystalline polymers, gels can be prepared by crystallizing the polymer from solution, either a homogeneous solution or a demixed solution. Foams can be prepared from these gels by the supercritical extraction of the solvent. By understanding and utilizing the phase separation behavior of polymer solutions, engineered microcellular foams can be prepared. To design the foams for any application one must be able to characterize their morphology. Results will be presented on the morphological characterization of these foams and the relationship of the morphology to their processing history. 14 refs., 12 figs.

Infrared absorption and photoluminescence have been demonstrated for InAs{sub 1-x}Sb{sub x}/InSb strained-layer superlattices (SLS's) in the 8--15 {eta}m region for As content less than 20%. This extended infrared activity is due to the type II heterojunction band offset in these SLS's. The preparation of the first MOCVD grown p-n junction diode was achieved by using dimethyltellurium as an in-type dopant. Several factors, such as background doping and dopant profiles affect the performance of this device. InSb diodes have been prepared using tetraethyltin. The resulting current-voltage characteristics are improved over those of diodes grown previously using dimethyltellurium. Doping levels of 8 {times} 10{sup 15} to 5 {times} 10{sup 18} cm{sup {minus}3} and mobilities of 6.7 {times} 10{sup 4} to 1.1 {times} 10{sup 4} cm{sup 2}/Vs have been measured for Sn doped InSb. SLS diode structures have been prepared using Sn and Cd as the dopants. Structures prepared with p-type buffer layers are more reproducible. 5 refs., 4 figs.

This paper describes the analysis of the Three Mile Island-2 (TMI-2) standard problem that was performed with MELCOR. The MELCOR computer code is being developed by Sandia National Laboratories for the Nuclear Regulatory Commission for the purpose of analyzing severe accident in nuclear power plants. The primary role of MELCOR is to provide realistic predictions of severe accident phenomena and the radiological source team. The analysis of the TMI-2 standard problem allowed for comparison of the model predictions in MELCOR to plant data and to the results of more mechanistic analyses. This exercise was, therefore valuable for verifying and assessing the models in the code. The major trends in the TMI-2 accident are reasonably well predicted with MELCOR, even with its simplified modeling. Comparison of the calculated and measured results is presented and, based on this comparison, conclusions can be drawn concerning the applicability of MELCOR to severe accident analysis. 5 refs., 10 figs., 3 tabs.

Steady state roughness of surfaces growing by molecular beam epitaxy is investigated by Monte Carlo simulations under conditions where an ion beam is also present which sputters adatoms off the surface. If the sputtering is random, it only increases the roughness. But if the sputtering probability is strongly dependent on the binding energy of an adatom within a cluster or island, the ions can have a smoothening effect. Physical arguments are given in support of the results. 8 refs., 4 figs.

The purpose of this paper is to discuss the current issues of interest in PV concentrator module reliability. Before describing in detail the reliability concerns about PV concentrator modules, it should be emphasized that, with proper design and attention to quality control, there is nothing to prevent concentrator modules from being as reliable as crystalline-silicon flat-plate modules have proven to be. Concentrator modules tested outdoors, as well as in the first-generation systems, have generally been reliable, and no degradation in cell output has been observed. Also, although they are not included in this paper, there are a few items currently of concern with the reliability of other PV module technologies that are not issues with PV concentrator technology, such as the stability of amorphous-silicon efficiencies and concerns about EVA encapsulation.