Publications

Midband (1KHz -- 500MHz) analog fiber optic data links were purchased for evaluation from three suppliers. Ortel Corp., Alhambra, CA, provided units built to the specifications. Kaman Sciences Corp, Colorado Springs, CO and Laser Diode Inc., Princeton, NJ, provided units similar to the specification but with significant differences. The final version of the Ortel units met the specification but were marginal in dynamic range. The other units failed to meet the specification but showed promise for future application.

Amid all the changes in the nuclear weapons complex, one intransigent fact remains: an enduring nuclear deterrent will not be possible without a continuing surveillance program to (1) find aging and other stockpile problems so that they can be fixed and (2) assure that when we do not find problems, none exist. Surveillance involves destructive or degrading tests that will exhaust planned provisions for rebuilding or replacing sample weapons in the not-too-distant future. This document discusses needed preparations for conducting surveillance in a future where production of new types of weapons is unlikely. Near-term opportunities to minimize the impact of extended surveillance are identified, and the need to maintain production capabilities is explained.

A subsurface-imaging synthetic-aperture radar (SISAR) has potential for application in areas as diverse as non-proliferation programs for nuclear weapons to environmental monitoring. However, most conventional synthetic-aperture radars operate at higher microwave frequencies which do not significantly penetrate below the soil surface. This study attempts to provide a basis for determining optimum frequencies and frequency ranges which will allow synthetic-aperture imaging of buried targets. Since the radar return from a buried object must compete with the return from surface clutter, the signal-to-clutter ratio is an appropriate measure of performance for a SISAR. A parameter-based modeling approach is used to model the complex dielectric constant of the soil from measured data obtained from the literature. Theoretical random-surface scattering models, based on statistical solutions to Maxwell`s equations, are used to model the clutter. These models are combined to estimate the signal-to-clutter ratio for canonical targets buried in several soil configurations. Initial results indicate that the HF spectrum (3--30 MHz), although it could be used to detect certain targets under some conditions, has limited practical value for use with SISAR, while the upper vhf through uhf spectrum ({approximately}100 MHz--1 GHz) shows the most promise for a general purpose SISAR system. Recommendations are included for additional research.

The MC4033 Common Radar, developed for the B61/83 Stockpile Improvement Program, required a small, rugged crystal resonator in an all-ceramic package capable of providing a frequency of 20 MHz. A commercially available crystal resonator, manufactured by Statek Corporation, met this requirement. This report describes the design intent, component characteristics, and evaluation test results for this device.

A radial transmission line material measurement sample apparatus (sample holder, offset short standards, measurement software, and instrumentation) is described which has been proposed, analyzed, designed, constructed, and tested. The purpose of the apparatus is to obtain accurate surface impedance measurements of lossy, possibly anisotropic, samples at low and intermediate frequencies (vhf and low uhf). The samples typically take the form of sections of the material coatings on conducting objects. Such measurements thus provide the key input data for predictive numerical scattering codes. Prediction of the sample surface impedance from the coaxial input impedance measurement is carried out by two techniques. The first is an analytical model for the coaxial-to-radial transmission line junction. The second is an empirical determination of the bilinear transformation model of the junction by the measurement of three full standards. The standards take the form of three offset shorts (and an additional lossy Salisbury load), which have also been constructed. The accuracy achievable with the device appears to be near one percent.

A new contact detection algorithm has been developed to address difficulties associated with the numerical simulation of contact in nonlinear finite element structural analysis codes. Problems including accurate and efficient detection of contact for self-contacting surfaces, tearing and eroding surfaces, and multi-body impact are addressed. The proposed algorithm is portable between dynamic and quasi-static codes and can efficiently model contact between a variety of finite element types including shells, bricks, beams and particles. The algorithm is composed of (1) a location strategy that uses a global search to decide which slave nodes are in proximity to a master surface and (2) an accurate detailed contact check that uses the projected motions of both master surface and slave node. In this report, currently used contact detection algorithms and their associated difficulties are discussed. Then the proposed algorithm and how it addresses these problems is described. Finally, the capability of the new algorithm is illustrated with several example problems.

Four fluorosilica clad, all silica core fibers with polyamide buffers were examined for radiation-induced, transient absorption in the central cavity of the Annular Core Research Reactor. The reactor operated 24 times in the pulse mode, typically yielding gamma doses of 15 krad(Si) and neutron fluences of 1.4 {times}10{sup 14} nts/cm{sup 2} thermal and 1.0 {times} 10{sup 15} nts/cm{sup 2} (fast). The two low-OH fibers absorbed 90% of the light in the 400 to 500 nm region and 30% in the 700 and 800 nm region. The high-OH fibers absorbed 20% in the 400 to 500 nm region and 50% in the 700 to 800 nm region. Saturation of the transient induced absorption was observed in all the fibers. No systematic measurements were taken of long term induced absorption. However, excessive absorption was not a problem in any fibers, even those that received total gamma doses of 5 Mrad(Si). Scintillation in the 680 to 820 mn band was observed. This report documents the data from these experiments.

Evolution of the microstructure of Al-2wt.%Cu thin films is examined with respect to how the presence of copper can influence electromigration behavior. After an anneal that simulates a thin film sintering step, the microstructure of the Al-Cu films consisted of 1 {mu}m aluminum grains with {theta}-phase A1{sub 2}Cu precipitates at grain boundaries and triple points. The grain size and precipitation distribution did not change with subsequent heat treatments. Upon cooling to room temperature the heat treatment of the films near the Al/Al+{theta} solvus temperature results in depletion of copper at the aluminum grain boundaries. Heat treatments lower in the two phase region (200 to 300C) result in enrichment of copper at the aluminum grain boundaries. Here, it is proposed that electromigration behavior of aluminum is improved by adding copper because the copper enrichment in the form of A1{sub 2}Cu phase may hinder aluminum diffusion along the grain boundaries.

The solution of Grand Challenge Problems will require computations which are too large to fit in the memories of even the largest machines. Inevitably new designs of I/O systems will be necessary to support them. Through our implementations of an out-of-core LU factorization we have learned several important lessons about what I/O systems should be like. In particular we believe that the I/O system must provide the programmer with the ability to explicitly manage storage. One method of doing so is to have a partitioned secondary storage in which each processor owns a logical disk. Along with operating system enhancements which allow overheads such as buffer copying to be avoided, this sort of I/O system meets the needs of high performance computing.

An eXplosive CHEMical kinetics code, XCHEM was developed to solve the reactive diffusion equations associated with thermal ignition of energetic material. This method-of-lines code uses stiff numerical methods and adaptive meshing. Solution accuracy is maintained between multilayered materials consisting of blends of reactive components and/or inert materials. Phase change and variable properties are included in one-dimensional slab, cylindrical and spherical geometries. Temperature-dependent thermal properties was incorporated and modification of thermal conductivities to include decomposition effects are estimated using solid/gas volume fractions determined by species fractions. Gas transport properties are also included. Time varying temperature, heat flux, convective and thermal radiation boundary conditions, and layer to layer contact resistances are also implemented. The global kinetic mechanism developed at Lawrence Livermore National Laboratory (LLNL) by McGuire and Tarver used to fit One-Dimensional Time to eXplosion (ODTX) data for the conventional energetic materials (HMX, RDX, TNT, and TATB) are presented as sample calculations representative of multistep chemistry. Calculated and measured ignition times for explosive mixtures of Comp B (RDX/TNT), Octol, (HMX/TNT), PBX 9404 (HMX/NC), and RX-26-AF (HMX/TATB) are compared. Geometry and size effects are accurately modeled, and calculations are compared to experiments with time varying boundary conditions. Finally, XCHEM calculations of initiation of an AN/oil/water emulsion, resistively heated, are compared to measurements.

Diamond films were deposited on tungsten substrates by a filament-assisted chemical vapor deposition process as a function of seven different processing parameters. The effect of variations in measured film characteristics such as growth rate, texture, diamond-to-nondiamond carbon Raman band intensity ratio and strain on the adhesion between the diamond film/tungsten substrate pairs as measured by a tensile pull method were investigated. The measured adhesion values do not correlate with any of the measured film characteristics mentioned above. The problem arises because of the non-reproducibility of the adhesion test results, due to the non-uniformity of film thickness, surface preparation and structural homogeneity across the full area of the substrate.

The porosity of sol-gel thin films may be tailored for specific applications through control of the size and structure of inorganic polymers within the coating sol, the extent of polymer reaction and interpenetration during film formation, and the magnitude of the capillary pressure exerted during the final stage of drying. By maximizing the capillary pressure and avoiding excessive condensation, dense insulating films may be prepared as passivation layers on silicon substrates. Such films can exhibit excellent dielectric integrity, viz., low interface trap densities and insulating properties approaching those of thermally grown SiO{sub 2}. Alternatively, through exploitation of the scaling relationship of mass and density of fractal objects, silica films can be prepared that show a variation in porosity (7--29 %) and refractive index (1.42--1.31) desired for applications in sensors, membranes, and photonics.

Parametric calculations are performed, using the SAFSIM computer program, to investigate the fluid mechanics and heat transfer performance of a particle bed fuel element. Both steady-state and transient calculations are included, addressing such issues as flow stability, reduced thrust operation, transpiration drag, coolant conductivity enhancement, flow maldistributions, decay heat removal, flow perturbations, and pulse cooling. The calculations demonstrate the dependence of the predicted results on the modeling assumptions and thus provide guidance as to where further experimental and computational investigations are needed. The calculations also demonstrate that both flow instability and flow maldistribution in the fuel element are important phenomena. Furthermore, results are encouraging that geometric design changes to the element can significantly reduce problems related to these phenomena, allowing improved performance over a wide range of element power densities and flow rates. Such design changes will help to maximize the operational efficiency of space propulsion reactors employing particle bed fuel element technology. Finally, the results demonstrate that SAFSIM is a valuable engineering tool for performing quick and inexpensive parametric simulations addressing complex flow problems.

Ten MC4073/4369 programmer base plates were analyzed. This component, a programmer base plate for the SRAM II (and later the SRAM A), is specified as a Grade C quality casting made of aluminum Alloy A356, heat treated to the T6 condition. A concern was expressed regarding the choice of an A356 casting for this application, given the complexity and severity of the loading environment. Preliminary tests and analyses suggested that the design was adequate, but noted the uncertainty involved in a number of their underlying assumptions. The uncertainty was compounded by the discovery that the casting used in the original series of mechanical tests failed. In this investigation, several production castings were examined and found to be of a quality superior to that required under current specifications. Their defect content and microstructure were studied and compared with published data to establish a mechanical property data base. The data base was supplemented with a series of X-direction static tests, which characterized the loading environment and measured the overall casting performance. It was found that the mechanical properties of the supplied castings were adequate for the anticipated X-direction loading environment, but the component is not over-designed. The established data base further indicates that a reduction in casting quality to the allowable level could result in failure of the component. Recommendations were made including (1) change the component specification to require higher casting quality in highly stressed areas, (2) supplement the inspection procedures to ensure adequate quality in critical regions, (3) alter the component design to reduce the stress levels in the mounting feet, (4) substitute a modified A356 alloy to improve the mechanical properties and their consistency, and (5) more thoroughly establish a data base for the mechanical property consequences of levels and configurations of casting defects.

This document is the Maintenance Manual for the Beneficial Uses Shipping System (BUSS) cask. These instructions address requirements for maintenance, inspection, testing, and repair, supplementing general information found in the BUSS Safety Analysis Report for Packaging (SARP), SAND 83-0698. Use of the BUSS cask is authorized by the Department of Energy (DOE) and the Nuclear Regulatory Commission (NRC) for the shipment of special form cesium chloride or strontium flouride capsules.

CAMCON, the Compliance Assessment Methodology CONtroller, is an analysis system that assists in assessing the compliance of the Waste Isolation Pilot Plant (WIPP) with applicable long-term regulations of the US Environmental Protection Agency, including Subpart B of the Environmental Standards for the Management and Disposal of spent Nuclear Fuel, High-Level and Transuranic Radioactive Wastes, 40 CFR 191 and 40CFR268.6, which is the portion of the Land Disposal Restrictions implementing the Resource, Conservative, and Recovery Act of 1976, as amended that states the conditions for disposal of hazardous chemical wastes. This manual provides an architectural overview of the CAMCON system. Furthermore this manual presents guidelines and presents suggestions for programmers developing the many different types of software necessary to investigate various events and physical processes of the WIPP. These guidelines include user interface requirements, minimum quality assurance requirements, coding style suggestions, and the use of numerous software libraries developed specifically for or adapted for the CAMCON system.

This volume contains a description of the codes and input/output files used to perform the LaSalle Level II/III Probabilistic Risk Assessment. A chart showing the process flow is presented and the relationship between the codes and the needed input and output data is discussed. Code listings for codes not documented elsewhere and complete or sample listings of the input and output files are also presented.

This report contains an initial definition of the field tests proposed for the Yucca Mountain Project repository sealing program. The tests are intended to resolve various performance and emplacement concerns. Examples of concerns to be addressed include achieving selected hydrologic and structural requirements for seals, removing portions of the shaft liner, excavating keyways, emplacing cementitious and earthen seals, reducing the impact of fines on the hydraulic conductivity of fractures, efficient grouting of fracture zones, sealing of exploratory boreholes, and controlling the flow of water by using engineered designs. Ten discrete tests are proposed to address these and other concerns. These tests are divided into two groups: Seal component tests and performance confirmation tests. The seal component tests are thorough small-scale in situ tests, the intermediate-scale borehole seal tests, the fracture grouting tests, the surface backfill tests, and the grouted rock mass tests. The seal system tests are the seepage control tests, the backfill tests, the bulkhead test in the Calico Hills unit, the large-scale shaft seal and shaft fill tests, and the remote borehole sealing tests. The tests are proposed to be performed in six discrete areas, including welded and non-welded environments, primarily located outside the potential repository area. The final selection of sealing tests will depend on the nature of the geologic and hydrologic conditions encountered during the development of the Exploratory Studies Facility and detailed numerical analyses. Tests are likely to be performed both before and after License Application.

In July 1990 the Institute of Nuclear Materials Management (INMM) [open quotes]International Safeguards Subcommittee[close quotes], an arm of the INMM [open quotes]Safeguards Committee[close quotes], held its first meeting, which was devoted principally to organizational matters. The goal of this organization is to promote International Safeguards as a major tool of Non Proliferation polices. Within the framework of the INMM, it has the responsibility to provide a forum for exchange of information related to further development of selected aspects of International Safeguards, and to enhance a broader understanding of these topics. A second meeting of this [open quotes]Subcommittee[close quotes] was held at the 1991 INMM Annual Meeting. In November 1991, the INMM reorganized into [open quotes]Divisions[close quotes], with the establishment of the [open quotes]International Safeguards and Non Proliferation Division[close quotes] (IS NP). From November 1991, the IS NP Division met two times, once in Europe and once in the USA. In October 1992, further reorganization of the INMM led to establishment of the [open quotes]International Safeguards Division[close quotes] (ISD) which, under the new designation, has met two times, once in Europe and once in Japan. This paper presents the purpose, objectives, results of past meetings, and future plans of the ISD.

Training new users of complex machines is often an expensive and time-consuming process. This is particularly true for special purpose systems, such as those frequently encountered in DOE applications. This paper presents a computer-based training system intended as a partial solution to this problem. The system extends the basic virtual reality (VR) training paradigm by adding a multimedia component which may be accessed during interaction with the virtual environment: The 3D model used to create the virtual reality is also used as the primary navigation tool through the associated multimedia. This method exploits the natural mapping between a virtual world and the real world that it represents to provide a more intuitive way for the student to interact with all forms of information about the system.

This paper describes a current research program at Sandia National Laboratories whereby magnetic stripes made from very high coercivity magnetic materials are produced through the use of a new particle rotation technology. This new process allows the stripes to be produced in bulk and then held in a latent state so that they may be encoded at a later date. Since particle rotation is less dependent on the type of magnetic particle used, very high coercivity particles could provide a way to increase both magnetic tamper-resistance and accidental erasure protection of the magnetic stripes.

SPR-IIIM is a modernized, improved version of SPR-111. The new system is expected to improve overall reliability and performance while reducing personnel dose and maintenance frequency. A description of the SPR-IIIM reactor and its features are presented in this paper along with plans for characterizing the reactors operational and safety characteristics. Enhancements of SPR-IIIM include a larger central irradiation cavity, 7.5 in. ID, a self-aligning safety block, spring-loaded fuel clamping, forced flow cooling across fuel plate gaps, and larger diameter hollow shafts with precision spline bearings support the reflector control elements.

One of the drivers in the dismantlement and disposal of nuclear weapon components is Envirorunental Protection Agency (EPA) guidelines. The primary regulatory driver for these components is the Resource Conservation Recovery Act (RCRA). Nuclear weapon components are heterogeneous and contain a number of hazardous materials including heavy metals, PCB`S, selfcontained explosives, radioactive materials, gas-filled tubes, etc. The Waste Component Recycle, Treatment, Disposal and Integrated Demonstration (WeDID) is a Department of Energy (DOE) Environmental Restoration and Waste Management (ERWM) sponsored program. It also supports DOE Defense Program (DP) dismantlement activities. The goal of WeDID is to demonstrate the end-to-end disposal process for Sandia National Laboratories designed nuclear weapon components. One of the primary objectives of WeDID is to develop and demonstrate advanced system treatment technologies that will allow DOE to continue dismantlement and disposal unhindered even as environmental regulations become more stringent. WeDID is also demonstrating waste minimization techniques by recycling a significant weight percentage of the bulk/precious metals found in weapon components and by destroying the organic materials typically found in these components. WeDID is concentrating on demonstrating technologies that are regulatory compliant, are cost effective, technologically robust, and are near-term to ensure the support of DOE dismantlement time lines. The waste minimization technologies being demonstrated by WeDID are cross cutting and should be able to support a number of ERWM programs.

Interactive Collaborative Environments (ICE) technologies allow teames at separate locations to work concurrently on joint problem solving. Examples of ICE use include engineers simultaneously viewing and manipulating the same CAD application to discuss design/production changes and trade-offs. This concept was demonstrated in March of 1992 between AT&T, Shreveport Works and Holmdel. In May 1992, Sandia National Laboratories demonstrated a platform independent version of application sharing code using the workstations and application software available at AT&T, Shreveport Works. AT&T and Sandia are currently negotiating future work agreements. In addition, Sandia has provided demonstrations and created pilot project links for internal Sandia use, and for communication with other facilities, e.g. Los Alamos National Laboratories and Sandia, California location. ICE can also be used to link up suppliers and customers, even in different companies. Anywhere team members are separated geographically, or even between building and facilities at a particular site, ICE can improve remote problem solving, cutting down on delays and miscommunication flascoes.

There is a need for sensitive detection of organophosphonates by inexpensive, portable instruments. Two kinds of chemical sensors, based on surface acoustic wave (SAW) devices and fiberoptic micromirrors, show promise for such sensing systems. Chemically sensitive coatings are required for detection, and data for thin films of the polymer polysiloxane are reported for both kinds of physical transducers. Both kinds of sensors are shown to be capable of detecting concentrations of diisopropylmethylphosphonate (DIMP) down to 1 ppm. © 1993 Humana Press Inc.

The combination of an energy dispersive x-ray spectrometer (EDS) with the ultrahigh vacuum environment of many modern electron microscopes requires the spectrometer designer to take extra precautions and presents the microscopist with the additional option of utilizing windowless spectrometers for light element detection while not worrying about contamination of the detector. UHV is generally defined as a pressure of better than 10{sup {minus}7} Pa and is necessary to prevent specimen modification by the components of the vacuum. UHV may also be defined as an environment in which the time to form a monolayer on the specimen is equal to or longer than the usual time for a laboratory measurement. This report examines performance of energy dispersion x-ray spectrometers in UHV.

This report discusses animating engineering science using an animation visualization system.

The primary difficulty of computing the vibration of spinning inflated membranes arises from the low natural frequencies of such systems. When such systems are rotated near their own natural frequencies the dynamics equations must account for higher order kinematics than is necessary for more rigid structures. These complications results from the membrane loads that develop within the bodies in reaction to the accelerations of the overall body. When second order kinematics act against these membrane loads, the resulting energies become of the same order as the potential and kinetic energies of the vibrations that would be calculated by first order kinematics. These complications apply to the problem addressed here. Here we consider a spin-stabilized, inflated membrane, spinning around its minor axis. This structure is very flexible and somewhat viscoelastic, so vibrations excited by the overall motion of the structure will dissipate energy of the system, thus reducing the kinetic energy. A reduction in kinetic energy consistent with a conservation of angular momentum results in coning and, eventually, tumbling. Here we must address the excitation of vibration by the rigid-body motion and then we must address the retarding effect of the energy dissipation on the rigid-body motion.

The properties of vertical-cavity surface-emitting lasers (VCSELS) and VCSEL-based optical switches using MOCVD-grown epitaxial material are discussed and sum their performance.

Parallel computing offers new capabilities for using molecular dynamics (MD) to simulate larger numbers of atoms and longer time scales. In this paper we discuss two methods we have used to implement the embedded atom method (EAM) formalism for molecular dynamics on multiple-instruction/multiple-data (MIMD) parallel computers. The first method (atom-decomposition) is simple and suitable for small numbers of atoms. The second method (force-decomposition) is new and is particularly appropriate for the EAM because all the computations are between pairs of atoms. Both methods have the advantage of not requiring any geometric information about the physical domain being simulated. We present timing results for the two parallel methods on a benchmark EAM problem and briefly indicate how the methods can be used in other kinds of materials MD simulations.

Solutions from a Parabolized Navier-Stokes (PNS) code with an algebraic turbulence model are compared with wall functions. The wall functions represent the turbulent flow profiles in the viscous sublayer, thus removing many grid points from the solution procedure. The wall functions are intended to replace the computed profiles between the body surface and a match point in the logarithmic region. A supersonic adiabatic flow case was examined first. This adiabatic case indicates close agreement between computed velocity profiles near the wall and the wall function for a limited range of suitable match points in the logarithmic region. In an attempt to improve marching stability, a laminar to turbulent transition routine was implemented at the start of the PNS code. Implementing the wall function with the transitional routine in the PNS code is expected to reduce computational time while maintaining good accuracy in computed skin friction.

CRESLAF is a Fortran program that predicts the velocity, temperature, and species profiles in two-dimensional (planar or axisymmetric) channels. The program accounts for finite-rate gas-phase and surface chemical kinetics and molecular transport. The model employs the boundary-layer approximations for the fluid-flow equations, coupled to gas-phase and surface species continuity equations. The program runs in conjunction with the Chemkin preprocessors for the gas-phase and surface chemical reaction mechanisms and the transport properties. This report presents the equations defining the model, the method of solution, the input parameters to the program, and a sample problem illustrating its use. Applications of CRESLAF include chemical vapor deposition (CVD) reactors, heterogeneous catalysis on reactor walls, and corrosion processes.

Biometric identity research and development activities are being conducted in universities, government, and private industry. This paper discusses some of the factors that limit the performance of biometric identity devices, looks at some new developments, and speculates on future developments.

Performance projections based on the analytical model of a scannerless laser radar system are compared to laboratory simulations and to field data measurements. Data and characteristics of the system, including camera response, image spatial resolution, and contributions to the signal-to-noise ratio are presented. A discussion of range resolution for this system will also be presented, and finally, the performance characteristics of the prototype benchtop system will be summarized.

In an effort to remain regulatory compliant, it is becoming increasingly important to locate resources that can provide up to date environmental regulations and regulatory interpretations. there are many resources available to provide information and training in these areas.

Remote systems are needed to accomplish many tasks such as the clean up of waste sites in which the exposure of personnel to radiation, chemical, explosive, and other hazardous constituents is unacceptable. In addition, hazardous operations which in the past have been completed by technicians are under increased scrutiny due to high costs and low productivity associated with providing protective clothing and environments. Traditional remote operations have, unfortunately, proven to also have very low productivity when compare with unencumbered human operators. However, recent advances in the integration of sensors and computing into the control of conventional remotely operated industrial equipment has shown great promise for providing systems capable of solving difficult problems.

This work concerns preparing tailored porous carbon monoliths by pyrolyzing porous polymer precursors. Prior work in this laboratory (1) demonstrated that a low density (0.05 g/cm{sup 3}), high void fraction (97 vol%) carbon monolith could be prepared by pyrolyzing a porous poly(acrylonitrile) (PAN) precursor. A higher density, more robust carbon material is preferred for certain applications, such as electrodes for electrochemical devices. The present work demonstrates that porous carbon monoliths having mass density of 0.7 g/cm{sup 3} can be prepared from a porous PAN precursor if the pyrolysis is controlled carefully. The macropore structure of the carbon is adjusted by changing the pore structure of the PAN precursor, and the finer scale structure (such as the crystallite size L{sub c}) is adjusted by varying the pyrolysis or heat treatment temperature.

The Arrhenius approach assumes a linear relation between log time to material property change and inverse absolute temperature. For elastomers, ultimate tensile elongation results are often used to confirm Arrhenius behavior, even though the ultimate tensile strength is non-Arrhenius. This paper critically examines the Arrhenius approach. Elongation vs air-oven aging temperature for a nitrile rubber, gives an E{sub a} of 22 kcal/mol; however this does not hold for the tensile strength, indicating degradation. Modulus profiling shows heterogeneity at the earliest times at 125 C, caused by diffusion-limited oxidation (DLO). Tensile strength depends on the force at break integrated over the cross section, and nitrile rubbers aged at different temperatures experience different degrees of degradation in the interior. Modulus at the surface, however, is not affected by DLO anomalies. Severe mechanical degradation will occur when the edge modulus increases by an order of magnitude. 7 figs, 3 refs.

Critical information required for Environment, Safety, and Health (ES&H) protection can be acquired with a comprehensive cradle-to-grave tracking and information system. The cradle-to-grave concept makes two initial assumptions. First, it is more effective to gather information at the origination of a process or entry point of a material and maintain that information during the rest of its life-cycle than to collect data on an ad hoc basis. Second, the information needs of the various ES&H programs have many commonalties. A system which adheres to a methodology based upon these assumptions requires a significant technical and administrative commitment; however, this investment, will in the long-term, reduce the effort and duplication of ES&H programs, improve the efficiency of ES&H and line personnel, and increase the scope and accuracy of ES&H data. The cradle-to-grave system being developed at Sandia National Laboratories (SNL) is designed to provide useful information on materials, personnel, facilities, hazards, wastes, and processes to fulfill the mission of pollution prevention, risk management, industrial hygiene, emergency preparedness, air/water quality, and hazardous and radioactive waste management groups. SNL is currently linking system modules, which are at various stages of development and production, to realize a cradle-to-grave tracking and information system that is functional for a large research and development laboratory.

A very brief description of two ``classes`` developed for use in design optimization and sensitivity analyses are given. These classes are used in simulations of systems in early design phases as well as system response assessments. The instanciated classes were coupled to system models to demonstrate the practically and efficiency of using these objects in complex robust design processes.

The Becker-Kistiakowsky-Wilson equation of state (BKW-EOS) has been calibrated over a wide initial density range near C-J states using measured detonation properties from 62 explosives at III total initial densities. Values for the empirical BKW constants {alpha}, {beta}, {kappa}, and {theta} were 0.5, 0.298, 10.5, and 6620, respectively. Covolumes were assumed to be invariant. Model evaluation includes comparison to measurements from 91 explosives composed of combinations of Al, B, Ba, C, Ca, Cl, F, H, N, 0, P, Pb, and Si at 147 total initial densities. Adequate agreement between predictions and measurements were obtained with a few exceptions for nonideal explosives. However, detonation properties for the nonideal explosives can be predicted adequately by assuming partial equilibrium. The partial equilibrium assumption was applied to aluminized composites of RDX, HMX, TNETB, and TNT to predict detonation velocity and temperature.

The multifrequency, multisource holographic method used in the analysis of seismic data is to extended electromagnetic (EM) data within the audio frequency range. The method is applied to the secondary magnetic fields produced by a borehole, vertical electric source (VES). The holographic method is a numerical reconstruction procedure based on the double focusing principle for both the source array and the receiver array. The approach used here is to Fourier transform the constructed image from frequency space to time space and set time equal to zero. The image is formed when the in-phase part (real part) is a maximum or the out-of-phase (imaginary part) is a minimum; i.e., the EM wave is phase coherent at its origination. In the application here the secondary magnetic fields are treated as scattered fields. In the numerical reconstruction, the seismic analog of the wave vector is used; i.e., the imaginary part of the actual wave vector is ignored. The multifrequency, multisource holographic method is applied to calculated model data and to actual field data acquired to map a diesel fuel oil spill.

An essential requirement for both Vertical Seismic Profiling (VSP) and Cross-Hole Seismic Profiling (CHSP) is the rapid acquisition of high resolution borehole seismic data. Additionally, full wave-field recording using three-component receivers enables the use of both transmitted and reflected elastic wave events in the resulting seismic images of the subsurface. To this end, an advanced three- component multi-station borehole seismic receiver system has been designed and developed by Sandia National Laboratory (SNL) and OYO Geospace. The system requires data from multiple three-component wall-locking accelerometer packages and telemeters digital data to the surface in real-time. Due to the multiplicity of measurement stations and the real-time data link, acquisition time for the borehole seismic survey is significantly reduced. The system was tested at the Chevron La Habra Test Site using Chevron`s clamped axial borehole vibrator as the seismic source. Several source and receiver fans were acquired using a four-station version of the advanced system. For comparison purposes, an equivalent data set was acquired using a standard analog wall-locking geophone receiver. The test data indicate several enhancements provided by the multi-station receiver relative to the standard, drastically improved signal-to-noise ratio, increased signal bandwidth, the detection of multiple reflectors, and a true 4:1 reduction in survey time.

The introduction of rapid prototyping machines into the market place promises to revolutionize the process of producing prototype parts with production-like quality. In the age of concurrent engineering and agile manufacturing, it is necessary to exploit applicable new technologies as soon as they become available. The driving force behind integrating these evolutionary processes into the design and manufacture of prototype parts is the need to reduce lead times and fabrication costs improve efficiency, and increase flexibility without sacrificing quality. Sandia Utilizes stereolithography and selective laser sintering capabilities to support internal design and manufacturing efforts. Stereolithography (SLA) is used in the design iteration process to produce proof-of-concept models, hands-on models for design reviews, fit check models, visual aids for manufacturing, and functional parts in assemblies. Selective laser sintering (SLS) is used to produce wax patterns for the lost wax process of investment casting in support of an internal Sandia National Laboratories program called FASTCAST which integrates experimental and computational technologies into the investment casting process. This presentation will provide a brief overview of the SLA and SLS processes and address our experiences with these technologies from the standpoints of application, accuracy, surface finish, and feature definition. Also presented will be several examples of prototype parts manufactured by the stereolithography and selective laser sintering rapid prototyping machines.

Three-dimensional finite element analyses of gas-filled storage caverns in domal salt were performed to investigate the effects of cavern spacing on surface subsidence, storage loss, and cavern stability. The finite element model used for this study models a seven cavern storage field with one center cavern and six hexagonally spaced surrounding caverns. Cavern spacing is described in terms of the P/D ratio which is the pillar thickness (the width between two caverns) divided by the cavern diameter. With the stratigraphy and cavern size held constant, simulations were performed for P/D ratios of 6.0, 3.0, 2.0, 1.0, and 0.5. Ten year simulations were performed modeling a constant 400 psi gas pressure applied to the cavern lining. The calculations were performed using JAC3D, a three dimensional finite element analysis code for nonlinear quasistatic solids. For the range of P/D ratios studied, cavern deformation and storage volume were relatively insensitive to P/D ratio, while subsidence volume increased with increasing P/D ratio. A stability criterion which describes stability in terms of a limiting creep strain was used to investigate cavern stability. The stability criterion indicated that through-pillar instability was possible for the cases of P/D = 0.5 and 1.0.

One of the proposed applications of the satellite-based Global Verification and Location System (GVLS) is the Authenticated Tracking and Monitoring System (ATMS). When fully developed, ATMS will provide the capability to monitor, in a secure and authenticated fashion, the status and global tracking of selected items while in transit - in particular, proliferation sensitive items. The resulting tracking, timing, and status information can then be processed and utilized to assure compliance with, for example, various treaties. Selected items to be monitored could include, but are not limited to, Treaty Limited Items (TLIs), such as nuclear weapon components, Re-entry Vehicles (RVs), weapon delivery and launch systems, chemical and biological agents, Special Nuclear Material (SNM), and related nuclear weapons manufacturing equipment. The ATMS has potential applications in the areas of arms control, disarmament and Non-proliferation treaty verification, military asset control, as well as International Atomic Energy Agency (IAEA) and Euratom safeguards monitoring activities. The concept presented here is mainly focused on a monitoring technology for proliferation sensitive items. It should, however, be noted that the systems potential applications are numerous and broad in scope, and could easily be applied to other types of monitoring activities as well.

This bulletin presents state of the art testing technology utilized at Sandia National Laboratory. A hand-held NiCad battery tester automatically checks batteries of individual cells. Modal analysis shows the way to better process control for integrated circuit lithography. An ultrasonic system pings reentry vehicles to measure in-flight ablation. A smaller VISAR shines in detonator tests. Higher image quality is achieved at neutron radiography facility with the use of a neutron collimator.

Over the past several years the Information Technology Department at Sandia Laboratories has developed information systems based on a solid foundation of information modeling and data administration. The output of the information modeling efforts is a fifth normal form relational table structure and associated data constraints. Developers would then implement the system by creating end-user application software. Traditionally, the development process combined the code necessary for maintaining data constraints with the code to provide the user interface (i.e. forms, windows, etc.). This approach has an adverse effect on the maintainability of the software as the system (i.e. the information model) changes over time. This paper will discuss the application of a direct connection between the information model and the implementation of a database with associated code to maintain required data constraints. The automated generation of this code allows the developers to concentrate on the user interface code development. The technique involves generating database procedure code automatically from the information modeling process. The database procedure code will enforce the data constraints defined in the information model. This has resulted in a fully functional database with complete rules enforcement within days of a completed information model. This work used the Knowledge Management Extensions of the Ingres database software. Changes to the architecture of both Application By Forms (ABF) and Ingres Windows4GL client applications required by this process will also be discussed.

This bulletin describes innovative manufacturing technologies being developed at Sandia National Laboratories. Topics in this issue include: new techniques to overcome barriers to large scale fabrication of vertical cavity surface-emitting lasers (VCSELs), variability reduction in plasma etching of microcircuits, using neural networks to evaluate effectiveness of flux-cleaning methods and alternative fluxes for printed circuit boards, ion implantation to increase the strength and wear resistance of aluminium, and a collaborative project to improve processing of thin-section welded assemblies. (GH)

A technique to integrate a dense, locally non-uniform mesh into finite-difference time-domain (FDTD) codes is presented. The method is designed for the full-wave analysis of multi-material layers that are physically thin, but perhaps electrically thick. Such layers are often used for the purpose of suppressing electromagnetic reflections from conducting surfaces. Throughout the non-uniform local mesh, average values for the conductivity and permittivity are used, where as variations in permeability are accommodated by splitting H-field line integrals and enforcing continuity of the normal B field. A unique interpolation scheme provides accuracy and late-time stability for mesh discontinuities as large as 1000 to 1. Application is made to resistive sheets, the absorbing Salisbury screen, crosstalk on printed circuit boards, and apertures that are narrow both in width and depth with regard to a uniform cell. Where appropriate, comparisons are made with the MoM code CARLOS and transmission-line theory. The hybrid mesh formulation has been highly optimized for both vector and parallel-processing on Cray YMP architectures.