Publications

In support of the Department of Energy`s Dismantlement Program, the Optoelectronics Characterization and Sensor Development Department 2231 at Sandia National Laboratories/New Mexico has developed an in situ nonintrusive Optoelectronic Inventory System (OIS) that has the potential for application wherever periodic inventory of selected material is desired. Using a network of fiber-optic links, the OIS retrieves and stores inventory signatures from data storage devices (which are permanently attached to material storage containers) while inherently providing electromagnetic pulse immunity and electrical noise isolation. Photovoltaic cells (located within the storage facility) convert laser diode optic power from a laser driver to electrical energy. When powered and triggered, the data storage devices sequentially output their digital inventory signatures through light-emitting diode/photo diode data links for retrieval and storage in a mobile data acquisition system. An item`s exact location is determined through fiber-optic network and software design. The OIS provides an on-demand method for obtaining acceptable inventory reports while eliminating the need for human presence inside the material storage facility. By using modularization and prefabricated construction with mature technologies and components, an OIS installation with virtually unlimited capacity can be tailored to the customer`s requirements.

To investigate the feasibility of producing a compact, efficient blue laser source, pumped-cavity second harmonic generation of diode lasers was explored. It is desirable to have such lasers to increase optical disk storage density, for color displays and for under-the-sea green-blue optical signal transmission. Based on assumed cavity losses, a cavity was designed and numerical analysis predicted an overall conversion efficiency to the second harmonic wavelength of 76% from a 75 mW diode laser. The diode laser used in these experiments had a single longitudinal and a single transverse mode output at 860 nm. The best conversion efficiency obtained (26%) was less than optimum due to the 2.5% single-pass linear losses associated with the cavity. However, calculations based on these higher losses are in good agreement with the experimentally determined values. In additions, a factor of 1.65 increase in the second harmonic output power is anticipated by reducing the input mirror reflectivity to better impedance-match the cavity. With this relatively low second harmonic conversion, the power to light conversion is 7.8%.

A series of explosive tests were performed to establish containment integrity data for commonly used handling and storage containers of energetic materials at Sandia National Laboratories, Albuquerque, N.M. The tests consisted of two phases: (1) each container was tested for explosive integrity and propagation, and (2) the data were used to evaluate a nominal donor-receptor test matrix for verifying the confinement integrity of a typical explosives service locker.

Synthetic Aperture Radar (SAR) from an airborne platform has been proposed for imaging targets beneath the earth`s surface. The propagation of the radar`s energy within the ground, however, is much different than in the earth`s atmosphere. The result is signal refraction, echo delay, propagation losses, dispersion, and volumetric scattering. These all combine to make SAR image formation from an airborne platform much more challenging than a surface imaging counterpart. This report treats the ground as a lossy dispersive half-space, and presents a model for the radar echo based on measurable parameters. The model is then used to explore various imaging schemes, and image properties. Dynamic range is discussed, as is the impact of loss on dynamic range. Modified window functions are proposed to mitigate effects of sidelobes of shallow targets overwhelming deeper targets.

This report is divided into: budget, capital equipment requests, general programmatic overview and institutional issues, DOE center of excellence for synthesis and processing of advanced materials, industrial interactions and technology transfer, and research program summaries (new proposals, existing programs). Ceramics, semiconductors, superconductors, interfaces, CVD, tailored surfaces, adhesion, growth and epitaxy, boron-rich solids, nanoclusters, etc. are covered.

Autosim is a software package written to control and trigger the programmable instruments that are used to supply simulated signals to the recording devices on underground nuclear weapons effects tests at the Nevada Test Site. These instruments are located either in the tunnel or at a remote site, and may be controlled from anywhere on the Department 9320 Computer Network. Autosim incorporates commands to control the operation of the Laser Calibrator that is a fiber optic device that transmits a signal from down-hole to the uphole recorders. Autosim also supports the task of characterizing the cable links by communicating to some high bandwidth digitizers that are used to input the pulse of the downhole simulator. To minimize the learning interval, Autosim utilizes menus and offers on-line help on most of the selections in the menu options.

Ceramic chip capacitors can potentially crack due to thermal stresses in a surface mount assembly process. The electrical performance of the cracked capacitors will degrade with time, and they will prematurely short. In high reliability applications, the cracked capacitors must be identified and eliminated. We have developed and demonstrated the temperature-humidity-bias (THB) aging technique to identify cracked capacitors. The initial phase of the study involved setting up automated test equipment to monitor 100 surface mounted capacitors at 85% relative humidity, 85{degree}C with 50 volts dc bias. The capacitors subjected to severe thermal shock were aged along with control samples. Failure mode analysis was done on the failed capacitors. The capacitors with surface cracks short-out within the first 8 hours of aging, whereas the capacitors that failed after a longer aging time (8 to 1000 hours) had a shorting path in an internal void. Internal voids are typical defects introduced during manufacturing of multilayer ceramic (MLC) capacitors. In the second phase of the study, we used the THB aging technique to study the effect of surface mount processes on capacitor cracking and, thus the reliability. The surface mount processes studied were vapor phase, infra-red (IR) and convection belt reflow soldering. The results shoed that 6.3% of vapor phase soldered capacitors, and 1.25% of the IR and convection belt soldered capacitors had cracks. In all capacitors, regardless of the solder process used, an additional 3 to 4% of the capacitors failed due to a shorting path in the internal void. The results of this study confirm that this technique can be used to screen cracked capacitors and compare different solder and manufacturing processes.

This report gives the results of a study of the production of electricity from geothermal energy with particular emphasis on the drilling of geothermal wells. A brief history of the industry, including the influence of the Public Utilities Regulatory Policies Act, is given. Demand and supply of electricity in the United States are touched briefly. The results of a number of recent analytical studies of the cost of producing electricity are discussed, as are comparisons of recent power purchase agreements in the state of Nevada. Both the costs of producing electricity from geothermal energy and the costs of drilling geothermal wells are analyzed. The major factors resulting in increased cost of geothermal drilling, when compared to oil and gas drilling, are discussed. A summary of a series of interviews with individuals representing many aspects of the production of electricity from geothermal energy is given in the appendices. Finally, the implications of these studies are given, conclusions are presented, and program recommendations are made.

FPT0 is the first of six tests that are scheduled to be conducted in an experimental reactor in Cadarache, France. The test apparatus consists of an in-pile fuel bundle, an upper plenum, a hot leg, a steam generator, a cold leg, and a small containment. Thus, the test is integral in the sense that it attempts to simulate all of the processes that would be operative in a severe nuclear accident. In FPT0, the fuel will be trace irradiated; in subsequent tests high burn-up fuel will be used. This report discusses separate pretest analyses of the FPT0 fuel bundle and primary circuit have been conducted using the USNRC`s source term code, VICTORIA-92. Predictions for release of fission product, control rod, and structural elements from the test section are compared with those given by CORSOR-M. In general, the releases predicted by VICTORIA-92 occur earlier than those predicted by CORSOR-M. The other notable difference is that U release is predicted to be on a par with that of the control rod elements; CORSOR-M predicts U release to be about 2 orders of magnitude greater.

This report identifies and describes emerging nondestructive inspection (NDI) methods that can potentially be used to inspect commercial transport and commuter aircraft for structural damage. The nine categories of emerging NDI techniques are: acoustic emission, x-ray computed tomography, backscatter radiation, reverse geometry x-ray, advanced electromagnetics, including magnetooptic imaging and advanced eddy current techniques, coherent optics, advanced ultrasonics, advanced visual, and infrared thermography. The physical principles, generalized performance characteristics, and typical applications associated with each method are described. In addition, aircraft inspection applications are discussed along with the associated technical considerations. Finally, the status of each technique is presented, with a discussion on when it may be available for use in actual aircraft maintenance programs. It should be noted that this is a companion document to DOT/FAA/CT-91/5, Current Nondestructive Inspection Methods for Aging Aircraft.

This report describes efforts conducted under Tasks 3 and 4 of the second phase of the project to develop a single-element stretched-membrane dish concept to reduce the cost of a high-performance concentrating solar collector. We completed the detailed design for such a collector suitable to drive a 25-kWe Stirling motor generator. The design includes the collectors, optical element, the drive, and support systems. The aperture of the optical element was sized to provide the required energy to the engine based on test data and analytical models of the concentrator receiver, and engine. The design of the optical element was improved based on experience gained from the design, fabrication, and testing of several prototypes.

This manual is intended to act as a working guide for setting up a Science Fair Volunteer Support Committee at your school. The Science Fair Volunteer Support Committee, or SFVSC, is the key component of the Science Fair Self-Help program, which was developed by Sandia National Laboratories and is designed to support a school`s science activities. The SFVSC is a team of parents and community volunteers who work in concert with a school`s teaching staff to assist and manage all areas of a school Science and Engineering Fair. The main advantage of creating such a committee is that it frees the science teachers from the organizational aspects of the fair and lets them concentrate on their job of teaching science. This manual is based on information gained through a Self-Help Development pilot program that was developed by Sandia National Laboratories during the 1991--92 school year at three Albuquerque, NM, middle schools. The manual describes the techniques that were successful in the pilot program and discusses how these techniques might be implemented in other schools. This manual also discusses problems that may be encountered, including suggestions for how they might be resolved.

The code HORSMIC was written to solve the problem of calculating the shape of hydrocarbon (gas or liquid) storage caverns formed by solution mining in bedded salt formations. In the past many storage cavems have been formed by vertically drilling into salt dome formations and solution mining large-aspect-ratio, vertically-axisymmetric caverns. This approach is generally not satisfactory for shallow salt beds because it would result in geomechanically-unstable, pancake-shaped caverns. In order to produce a high aspect ratio cavern in the horizontal direction a more complicated strategy must be employed. This report describes one such strategy, and documents the use of the computer model HORSMIC which can be used to estimate the shape of the cavern produced by a prescribed leaching schedule. Multiple trials can then be used to investigate the effects of various pipe hole configurations in order to optimize over the cavern shape.

The objective of the ``Hydrodynamics of Maneuvering Bodies`` LDRD project was to develop a Lagrangian, vorticity-based numerical simulation of the fluid dynamics associated with a maneuvering submarine. Three major tasks were completed. First, a vortex model to simulate the wake behind a maneuvering submarine was completed, assuming the flow to be inviscid and of constant density. Several simulations were performed for a dive maneuver, each requiring less than 20 cpu seconds on a workstation. The technical details of the model and the simulations are described in a separate document, but are reviewed herein. Second, a gridless method to simulate diffusion processes was developed that has significant advantages over previous Lagrangian diffusion models. In this model, viscous diffusion of vorticity is represented by moving vortices at a diffusion velocity, and expanding the vortices as specified by the kinematics for a compressible velocity field. This work has also been documented previously, and is only reviewed herein. The third major task completed was the development of a vortex model to describe inviscid internal wave phenomena, and is the focus of this document. Internal wave phenomena in the stratified ocean can affect an evolving wake, and thus must be considered for naval applications. The vortex model for internal wave phenomena includes a new formulation for the generation of vorticity due to fluid density variations, and a vortex adoption algorithm that allows solutions to be carried to much longer times than previous investigations. Since many practical problems require long-time solutions, this new adoption algorithm is a significant step toward making vortex methods applicable to practical problems. Several simulations are described and compared with previous results to validate and show the advantages of the new model. An overview of this project is also included.

This report documents results of a series of scoping experiments on boiling from downward-facing surfaces in support of the Sandia New Production Reactor, Vessel-Pool Boiling Heat Transfer task. Quenching experiments have been performed to examine the boiling processes from downward-facing surfaces using two 61-centimeter diameter test masses, one with a flat test surface and one with a curved test surface having a radius of curvature of 335 cm, matching that of the Cylindrical Boiling facility test vessel. Boiling curves were obtained for both test surfaces facing horizontally downward. The critical beat flux was found to be essentially the same, having an average value of approximately 0.5 MW/m{sup 2}. This value is substantially higher than current estimates of the heat dissipation rates required for in-vessel retention of core debris in the Heavy Water New Production Reactor as well as some of the advanced light water reactors under design. The nucleate boiling process was found to be cyclic with four relatively distinct phases: direct liquid/solid contact, nucleation and growth of bubbles, coalescence, and ejection.

This report describes the instrumentation locations of the Tore Supra Phase III Outboard Limiter, including the locations and signal names of the flowmeters and thermocouples. Shot 11044 was evaluated in some detail. The heat loads in the fourteen cooling tubes that form the limiter head were calculated from the data and the results compared with the heat loads predicted using a 3-D model heat transfer calculation that calculates the distribution of power on the limiter based upon the power scrape-off length, the mag magnetic configuration and the shape of the limiter.

A dual-element, stretched-membrane central receiver heliostat was designed and manufactured in 1989, by a private US company engaged in the development of commercial central receiver solar technology. The two-module collector, with a collection area of 97.5 m{sup 2}, extends stretched-membrane mirror technology on several fronts with face-down stow capability and a digital controller that integrates tracking and focusing control on a single programmable control board. The solar collector was installed at Sandia`s National Solar Thermal Test Facility in Albuquerque, New Mexico and evaluated over a three-and-a-half year period which ended in September 1993. The measured performance and the operational and maintenance characteristics of this commercial prototype are the subject of this report. The results of beam quality measurements, tracking repeatability tests, measurements of beam movement in elevated winds, performance tests of the focusing system, and all-day beam quality and tracking tests are presented, and the authors offer a detailed discussion of the knowledge gained through operation and maintenance and of the improvements made or suggested to the heliostat`s design.

This report presents the results of an inspection around fastener holes in simulated lap splice specimens using a Nortec-30 Eddyscan inspection system. The inspector performing the tests had no prior knowledge of the extent or location of cracks in the specimens examined. The results of the inspection are presented in terms of various probability of detection curve models and are compared to various other eddy current inspections performed on the same set of test specimens. Results indicate that the system is capable, with high confidence, of detecting 60 to 70 mil cracks from under countersink fasteners.

This report presents a provisional lifetime prediction method which attempts to account for creep- fatigue interactions typically encountered in the design of solar central receivers that spend a considerable fraction of their operating periods subjected to compressive stresses at elevated temperature. During its operating life, a solar central receiver will be exposed to a large number of startup/shut- down cycles (relative to other power-producing systems), along with only short periods (up to 10-12 hrs.) of steady-state operation during each daily cycle. As such, fatigue-related deformation is expected to dominate the damage leading to failure in the high temperature alloys used for such as receiver. Thus, the provisional method concentrates on a fatigue-based damage approach, with direct accounting for the effects of thermo-mechanical fatigue and hold times at elevated temperatures. Note that creep damage is treated in an implicit way only, by means of the hold time correction. The starting point for the methodology is the isothermal low cycle fatigue data set used to develop fatigue design curves for ASME Boiler and Pressure Vessel Code Case N-47. Since the original data were not available for materials of interest (316 Stainless Steel and Alloy 800H), we attempted to estimate the original data sets by stripping away the safety factors of 2 on Δϵ and 20 on N₁ from the N-47 design curves. These "baseline data curves" for N₁ versus Δϵ, which represent the mean low cycle fatigue properties for each alloy at a given temperature, are tabulated in the Appendix in both tabular format and by means of sixth-order polynomial equations. The baseline data curves are first reduced to account for the effects of frequency and hold time. Comparison of hold time data for both 316 SS and 800H have indicated that additional factors of safety are required to make the frequency and hold time reductions conservative for all data considered. Therefore, safety factors of 1.5 on Δϵ and 4.5 on N₁ are used, and these are shown to give generally conservative predictions. Finally, reductions for thermomechanical fatigue damage are made which are a function of f, the fraction of thermally imposed strain to the total imposed strain. It is expected that the resulting fatigue design curves should yield reasonable life predictions for the design of solar central receivers.

Performance assessment calculations are based on geochemical models that assume that interactions among radionuclides, rocks and groundwaters under natural conditions, can be estimated or bound by data obtained from laboratory-scale studies. The data include radionuclide distribution coefficients, measured in saturated batch systems of powdered rocks, and retardation factors measured in short-term column experiments. Traditional approaches to model validation cannot be applied in a straightforward manner to the simple reactive transport models that use these data. An approach to model validation in support of performance assessment is described in this paper. It is based on a recognition of different levels of model validity and is compatible with the requirements of current regulations for high-level waste disposal. Activities that are being carried out in support of this approach include (1) laboratory and numerical experiments to test the validity of important assumptions inherent in current performance assessment methodologies,(2) integrated transport experiments, and (3) development of a robust coupled reaction/transport code for sensitivity analyses using massively parallel computers.

We report the synthesis and optical properties of Rb[Ti{sub 1-2x}Ln{sub x}Nb{sub x}]OAsO{sub 4}. The solid solubility of lanthanide ions in the materials decreases exponentially as the size of the lanthanide ion increases. The materials exhibit absorption spectra characteristic of the particular lanthanide ion in the structure. The spectral regions between absorption peaks are transparent and will allow the transmission of fundamental and second-harmonic radiation. The charge transfer band is red-shifted 0 to 27 nm relative to RbTiOAsO{sub 4} (midpoint 331 nm). Second-harmonic intensities measured at 532 nm decrease exponentially as lanthanide ion concentration increases.

Saturation profiles resulting from TOUGH2 numerical simulations of water infiltration into a tuff matrix from a saturated vertical fracture have been compared to experimental results. The purpose was to determine the sensitivity of the infiltration on local heterogeneities and different representations of two-phase characteristic curves used by the model. Findings indicate that the use of simplified (linearized) capillary pressure curves with rigorous (van Genuchten) relative permeability curves resulted in a more computationally efficient solution without a loss in accuracy. However, linearized forms of the relative permeability functions produced poor results, regardless of the form of the capillary pressure function. In addition, numerical simulations revealed that the presence of local heterogeneities in the tuff caused non-uniform saturation distributions and wetting fronts in the in matrix.

As Sandia National Laboratories and the Physical and Chemical Sciences Center develop an increasingly diverse set of customers, research partners, and Cooperative Research and Development Agreements (CRADA`s) with industry, there is a need for providing more concise information describing their technical achievements and capabilities. This publication, Research Briefs, is designed to inform the present and potential partners in research and technology advancement. Their research emphasizes semiconductor physics, electronic materials, surface physics and chemistry, plasma and chemical processing sciences, lasers and optics, vision science, ion-solid interactions and defect physics, and advanced materials physics. The specific programs they pursue are driven by the research goals which are greatly influenced by interactions with the government and industrial customers.

Tests were performed to evaluate the corrosivity of several nitrate salt mixtures on the containment materials likely to be used in a molten-salt solar central receiver power plant. Objective was to determine if common salt impurities (e.g., chloride) aggravate corrosion. The test was conducted for 7008 hours on A36 carbon steel at 320C and 304 and 316 stainless steels at 570C. Seven salt mixture containing a variety of impurity concentrations were used. Corrosion rates were determined by descaled weight loss for coupons removed periodically from the melts. The nitrate mixtures were analyzed for changes in impurity levels and accumulation of soluble corrosion products. Test results indicate generally that corrosion is slow and that impurities do not contribute dramatically to corrosion rates of carbon and stainless steels.

Ion implantation in insulators causes modifications in the refractive-index as a result of radiation damage, phase separation, or compound formation. As a consequence, light waveguides may be formed with interesting applications in the field of optoelectronics. Recently implantation of metals ions (e.g. silver, copper, gold, lead,...) showed the possibility of small radii colloidal particles formation, in a thin surface layer of the glass substrate. These particles exhibit an electron plasmon resonance which depends on the optical constants of the implanted metal and on the refractive-index of the glass host. The non-linear optical properties of such colloids, in particular the enhancement of optical Kerr susceptibility, suggest that the, ion implantation technique may play an important role for the production of all-optical switching devices. In this paper an analysis of the state-of-the-art of the research in this field will be presented in the framework of ion implantation in glass physics and chemistry.