Publications

Abstract not provided.

Abstract not provided.

Ultrasonic wave propagation decreases as a material is heated. Two factors that can characterize material properties are changes in wave speed and energy loss from interactions within the media. Relatively small variations in velocity and attenuation can detect significant differences in microstructures. This paper discusses an overview of experimental techniques that document the changes within a highly attenuative material as it is either being heated or cooled from 25°C to 90°C. The experimental set-up utilizes ultrasonic probes in a through-transmission configuration. The waveforms are recorded and analyzed during thermal experiments. To complement the ultrasonic data, a Discontinuous-Galerkin Model (DGM) was also created which uses unstructured meshes and documents how waves travel in these anisotropic media. This numerical method solves particle motion travel using partial differential equations and outputs a wave trace per unit time. Both experimental and analytical data are compared and presented.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The Federal Aviation Administration Airworthiness Assurance NDI Validation Center currently assesses the capability of various non-destructive inspection (NDI) methods used for analyzing aircraft components. The focus of one such exercise is to evaluate the sensitivity of fluorescent liquid penetrant inspection. A baseline procedure using the water-washable fluorescent penetrant method defines a foundation for comparing the brightness of low cycle fatigue cracks in titanium test panels. The analysis of deviations in the baseline procedure will determine an acceptable range of operation for the steps in the inspection process. The data also gives insight into the depth of each crack and which step(s) of the inspection process most affect penetrant sensitivities. A set of six low cycle fatigue cracks produced in 6.35-mm thick Ti-6Al-4V specimens was used to conduct the experiments to produce sensitivity data. The results will document the consistency of the crack readings and compare previous experiments to find the best parameters for water-washable penetrant.

The Federal Aviation Administration's Airworthiness Assurance NDI Validation Center (AANC) is currently conducting experiments with Level 4, Method B penetrant on low cycle fatigue specimens. The main focus of these experiments is to document the affect on penetrant brightness readings by varying inspection parameters. This paper discusses the results of changing drying temperature, drying time, and dwell time of both penetrant and emulsifier on low cycle fatigue specimens.

Several ultrasonic inspection methods were developed at the Federal Aviation Administration's Airworthiness Assurance NDI Validation Center (AANC) to easily and rapidly detect hidden stress corrosion cracks in all vertical windshield posts on the US Coast Guard (USCG) HU-25 Guardian aircraft. The inspection procedure locates cracks as small as 2.0 millimeters emanating from internal fastener holes and determines their length. A test procedure was developed and a baseline assessment of the USCG fleet was conducted. Inspection results on twenty-five aircraft revealed a good correlation with results made during subsequent structural disassembly and visual inspection.

As III-V nitride device structures become more complicated and design rules shrink, well-controlled etch processes are necessary. Due to limited wet chemical etch results for the group-III nitrides, a significant amount of effort has been devoted to the development of dry etch processing. Dry etch development was initially focused on mesa structures where high etch rates, anisotropic profiles, smooth sidewalls, and equi-rate etching of dissimilar materials were required. For example, commercially available LEDs and laser facets for GaN-based laser diodes have been patterned using reactive ion etching (RIE). With the recent interest in high power, high temperature electronic devices, etch characteristics may also require smooth surface morphology, low plasma-induced damage, and selective etching of one layer over another. The principal criteria for any plasma etch process is its utility in the fabrication of a device. In this study, we will report plasma etch results for the group-III nitrides and their application to device structures.

The Federal Aviation Administration's Airworthiness Assurance NDI Validation Center (AANC) is currently characterizing low cycle fatigue specimens that will support the needs of penetrant manufacturers, commercial airline industry and the Federal Aviation Administration. The main focus of this characterization is to maintain and enhance the evaluation of penetrant inspection materials and apply resources to support the aircraft community needs. This paper discusses efforts to-date to document the Wright Laboratory penetrant evaluation process and characterize penetrant brightness readings in the initial set of sample calibration panels using Type 1 penetrant.

This paper presents an overview of several emerging nondestructive evaluation technologies that are being employed or considered for use to inspect commercial transport, commuter aircraft and military aircraft. An overview of the Federal Aviation Administration (FAA) Airworthiness Assurance NDI Validation Center (AANC) is described and how AANC teams with industry, universities, and other federal entities to assess these technologies.

This report presents a nondestructive inspection assessment of eddy current and electrochemical analysis to separate inconel alloys from stainless steel alloys as well as an evaluation of cleaning techniques to remove a thermal oxide layer on aircraft exhaust components. The results of this assessment are presented in terms of how effective each technique classifies a known exhaust material. Results indicate that either inspection technique can separate inconel and stainless steel alloys. Based on the experiments conducted, the electrochemical spot test is the optimum for use by airframe and powerplant mechanics. A spot test procedure is proposed for incorporation into the Federal Aviation Administration Advisory Circular 65-9A Airframe & Powerplant Mechanic - General Handbook. 3 refs., 70 figs., 7 tabs.

An eddy current inspection method was developed at the Federal Aviation Administration`s Airworthiness Assurance NDI Validation Center (AANC) to easily and rapidly detect subsurface fatigue cracks in the wheel well fairing on the US Coast Guard (USCG) HC-130H aircraft caused by fatigue. The inspection procedure locates cracks as small as 10.2 millimeters in length at 2.54 mm below the skin surface at raised fastener sites. The test procedure developed baseline three USCG aircraft. Inspection results on the three aircraft reveals good correlation with results made during subsequent structural disassembly.

The Federal Aviation Administration`s Airworthiness Assurance NDI Validation Center (AANC) and the Center for Aviation Systems Reliability (CASR) are currently working to develop a liquid penetrant inspection (LPI) system evaluation capability that will support the needs of the penetrant manufacturers, commercial airline industry and the FAA. The main focus of this facility is to support the evaluation of penetrant inspection materials, penetrant systems and to apply resources to support industry needs. This paper discusses efforts to create such a facility and an initial project to produce fatigue crack specimens for evaluation of Type 1 penetrant sensitivities.

Composite doublers are gaining popularity for their ability to repair and reinforce commercial aircraft structures and it is anticipated that the potential cost savings may spur wider use of this technology. But before composite doublers can be accepted by the civil aviation industry, inspection techniques must be developed to verify the integrity of the doubler and the parent material under the doubler. The Federal Aviation Administration Airworthiness Assurance NDI Validation Center (AANC) is currently developing test methods to inspect aircraft structures under composite doublers using low kilovoltage radiography. This paper documents the radiographic techniques developed by the AANC which have been found to give the best contrast of the radiographic image with reduced image distortion.

The Federal Aviation Administration Airworthiness Assurance Nondestructive Inspection Validation Center (FAA-AANC) and Boeing Commercial Airplane Group are currently developing a study pertaining to the detection of cracks in multi-layered aluminum sheets. The specimen panels model pertinent aspects of the lap splice joints for Boeing 737 aircraft, Line Numbers 292 - 2565. Upon initial characterization of the specimen panels, it became clear that signals produced from a sliding probe at fastener sites were not representative of an in-service lap splice, and therefore, could not be used in a probability of detection experiment. This paper discusses specimen characterization and steps taken to make the specimens useful for nondestructive technology assessment.

An ultrasonic inspection method was developed at FAA`s Airworthiness Assurance NDI Validation Center (AANC) to easily and rapidly detect hidden fatigue cracks in the copilot vertical windshield post on USCG (Coast Guard) HU-25 `Guardian` aircraft. The inspection procedure locates hidden cracks as small as 3.2 mm emanating from internal fastener holes and determines their length. A test procedure was developed and a baseline assessment of the USCG fleet conducted. Inspection results on 41 aircraft revealed good correlation with results made during subsequent structural disassembly and visual inspection of selected aircraft.

The dynamic performance of a 250 Hz resonant plate shock system which simulates pyrotechnic shock environments on micro-electrical components is evaluated. A series of experiments recording strain rate histories and acceleration time histories at several plate locations were conducted. This empirical data is used to compare the analytical results obtained from a finite element based numerical simulation. The comparison revealed a good correlation between experimental and analytical results.