Rutherford backscattering spectrometry (RBS), elastic recoil detection (ERD), proton induced x-ray emission (PIXE) and nuclear reaction analysis (NRA) are among the most commonly used, or traditional, ion beam analysis (IBA) techniques. In this review, several adaptations of these IBA techniques are described where either the approach used in the analysis or the application area is clearly non-traditional or unusual. These analyses and/or applications are summarized in this paper.
MOSFETs historically have exhibited large 1/f noise magnitudes because of carrier-defect interactions that cause the number of channel carriers and their mobility to fluctuate. Uncertainty in the type and location of defects that lead to the observed noise have made it difficult to optimize MOSFET processing to reduce the level of 1/f noise. This has limited one`s options when designing devices or circuits (high-precision analog electronics, preamplifiers, etc.) for low-noise applications at frequencies below {approximately}10--100 kHz. We have performed detailed comparisons of the low-frequency 1/f noise of MOSFETs manufactured with radiation-hardened and non-radiation-hardened processing. We find that the same techniques which reduce the amount of MOSFET radiation-induced oxide-trap charge can also proportionally reduce the magnitude of the low-frequency 1/f noise of both unirradiated and irradiated devices. MOSFETs built in radiation-hardened device technologies show noise levels up to a factor of 10 or more lower than standard commercial MOSFETs of comparable dimensions, and our quietest MOSFETs show noise magnitudes that approach the low noise levels of JFETS.
Three dimensional (3D) seismic technology is regarded as one of the most significant improvements in oil exploration technology to come along in recent years. This report provides an assessment of the likely long-term effect on the world oil price and some possible implications for the firms and countries that participate in the oil market. The potential reduction in average finding costs expected from the use of 3D seismic methods and the potential effects these methods may have on the world oil price were estimated. Three dimensional seismic technology is likely to have a more important effect on the stability rather than on the level of oil prices. The competitive position of US oil production will not be affected by 3D seismic technology.
A programming tool has been developed to allow detailed analysis of Fortran programs for massively parallel architectures. The tool obtains counts for various arithmetic, logical, and input/output operations by data types as desired by the user. The tool operates on complete programs and recognizes user-defined and intrinsic language functions as operations that may be counted. The subset of functions recognized by the tool, STOPCNTR, can be extended by altering the input data sets. This feature facilitates analysis of programs targeted for different architectures. The basic usage and operation of the tool is described along with the more important data structures and more interesting algorithmic aspects before identifying future directions in continued development of the tool and discussing STOPCNTR`s inherent advantages and disadvantages.
Tensile properties were measured for nineteen different formulations of epoxy encapsulating materials. Formulations were of different combinations of two neat resins (Epon 828 and Epon 826, with and without CTBN modification), three fillers (ALOX, GNM and mica) and four hardeners (Z, DEA, DETDA-SA and ANH-2). Five of the formulations were tested at -55, -20, 20 and 60C, one formulation at -55, 20 and 71C; and the remaining formulations at 20C. Complete stress-strain curves are presented along with tables of tensile strength, initial modulus and Poisson`s ratio. The stress-strain responses are nonlinear and are temperature dependent. The reported data provide information for comparing the mechanical properties of encapsulants containing the suspected carcinogen Shell Z with the properties of encapsulants containing noncarcinogenic hardeners. Also, calculated shear moduli, based on measured tensile moduli and Poisson`s ratio, are in very good agreement with reported shear moduli from experimental torsional pendulum tests.
Sandia National Laboratories is currently involved in the optimization of a Plane Shock Generator Explosive Lens (PSGEL). This PSGEL component is designed to generate a planar shock wave transmitted to perform a function through a steel bulkhead without rupturing or destroying the integrity of the bulkhead. The PSGEL component consists of a detonator, explosive, brass cone and tamper housing. The purpose of the PSGEL component is to generate a plane shock wave input to 4340 steel bulkhead (wave separator) with a ferro-electric (PZT) ceramic disk attached to the steel on the surface opposite the PSGEL. The planar shock wave depolarizes the PZT 65/35 ferroelectric ceramic to produce an electrical output. Elastic, plastic I and plastic II waves with different velocities are generated in the steel bulkhead. The depolarization of the PZT ceramic is produced by the elastic wave of specific amplitude (10--20 Kilobars) and this process must be completed before (about 0. 15 microseconds) the first plastic wave arrives at the PZT ceramic. Measured particle velocity versus time profiles, using a Velocity Interferometer System for Any Reflector (VISAR) are presented for the brass and steel output free surfaces. Peak pressures are calculated from the particle velocities for the elastic, plastic I and plastic 11 waves in the steel. The work presented here investigates replacing the current 4340 steel with PH 13-8 Mo stainless steel in order to have a more corrosion resistant, weldable and more compatible material for the multi-year life of the component. Therefore, the particle velocity versus time profile data are presented comparing the 4340 steel and PH 13-8 Mo stainless steel. Additionally, in order to reduce the amount of explosive, data are presented to show that LX-13 can replace PBX-9501 explosive to produce more desirable results.
Previous studies in this laboratory have demonstrated that DMBA alters biochemical events associated with lymphocyte activation including formation of the second messenger IP{sub 3} and the release of intracellular Ca{sup 2+}. The purpose of the present studies was to evaluate the mechanisms by which DMBA induces IP{sub 3} formation and Ca{sup 2+} release by examining phosphorylation of membrane associated proteins and activation of protein tyrosine kinases lck and fyn. These studies demonstrated that exposure of HPB-ALL cells to 10{mu}M DMBA resulted in a time- and dose-dependent increase in tyrosine phosphorylation of PLC-{gamma}1 that correlated with our earlier findings of IP{sub 3} formation and Ca{sup 2+} release. These results indicate that the effects of DMBA on the PI-PLC signaling pathway are in part, the result of DMBA-induced tyrosine phosphorylation of the PLC-{gamma}1 enzyme. The mechanism of DMBA- induced tyrosine phosphorylation of PLC-{gamma}1 may be due to activation of fyn or lck kinase activity, since it was found that DMBA increased the activity of these PTKs by more than 2-fold. Therefore, these studies demonstrate that DMBA may disrupt T cell activation by stimulating PTK activation with concomitant tyrosine phosphorylation of PLC-{gamma}1, release of IP{sub 3}, and mobilization of intracellular Ca{sup 2+}.
The Natural Excitation Technique (NExT) is a method of modal testing that allows structures to be tested in their ambient environments. This report is a compilation of developments and results since 1990, and contains a new theoretical derivation of NExT, as well as a verification using analytically generated data. In addition, we compare results from NExT with conventional modal testing for a parked, vertical-axis wind turbine, and, for a rotating turbine, NExT is used to calculate the model parameters as functions of the rotation speed, since substantial damping is derived from the aeroelastic interactions during operation. Finally, we compare experimental results calculated using NExT with analytical predictions of damping using aeroelastic theory.
Characteristics of a long pulse, low-pump rate, atomic xenon (XeI) laser are described. Energy loading up to 170 mJ/cc at pulse widths between 5 and 55 ms is achieved with an electron beam in transverse geometry. The small-signal gain coefficient, loss coefficient, and saturation intensity are inferred from a modified Rigrod analysis. For pump rates between 12 and 42 W/cc the small-signal gain coefficient varies between 0.64 and 0.91%/cm, the loss coefficient varies between 0.027 and 0.088%/cm, and the saturation intensity varies between 61 and 381 W/cm{sup 2}. Laser energy as a function of pulse width and the effects of air and CO{sub 2} impurities are described. The intrinsic laser energy efficiency has a maximum at a pulse width of 10 ms corresponding to a pump rate of 1.6 W/cc. No maximum is observed in the intrinsic power efficiency, A drastic reduction of laser output power is observed for impurity concentrations of greater than {approx}0.01%. An investigation of the dominant laser wavelength in a high Q cavity indicates that the 2.6-{mu}m radiation dominates. A comparison of dominant wavelength with reactor pumped results indicates good agreement when the same cavity optics are used.
This Executive Summary presents the methodology for determining containment requirements for spent-fuel transport casks under normal and hypothetical accident conditions. Three sources of radioactive material are considered: (1) the spent fuel itself, (2) radioactive material, referred to as CRUD, attached to the outside surfaces of fuel rod cladding, and (3) residual contamination adhering to interior surfaces of the cask cavity. The methodologies for determining the concentrations of freely suspended radioactive materials within a spent-fuel transport cask for these sources are discussed in much greater detail in three companion reports: ``A Method for Determining the Spent-Fuel Contribution to Transport Cask Containment Requirements,`` ``Estimate of CRUD Contribution to Shipping Cask Containment Requirements,`` and ``A Methodology for Estimating the Residual Contamination Contribution to the Source Term in a Spent-Fuel Transport Cask.`` Examples of cask containment requirements that combine the individually determined containment requirements for the three sources are provided, and conclusions from the three companion reports to this Executive Summary are presented.
This report discusses recent efforts to characterize the flow and density nonuniformities downstream of heated screens placed in a uniform flow. The Heated Screen Test Facility (HSTF) at Sandia National Laboratories and the Lockheed Palo Alto Flow Channel (LPAFC) were used to perform experiments over wide ranges of upstream velocities and heating rates. Screens of various mesh configurations were examined, including multiple screens sequentially positioned in the flow direction. Diagnostics in these experiments included pressure manometry, hot-wire anemometry, interferometry, Hartmann wavefront slope sensing, and photorefractive schlieren photography. A model was developed to describe the downstream evolution of the flow and density nonuniformities. Equations for the spatial variation of the mean flow quantities and the fluctuation magnitudes were derived by incorporating empirical correlations into the equations of motion. Numerical solutions of these equations are in fair agreement with previous and current experimental results.
Two heliostats representing the state-of-the-art in glass-metal designs for central receiver (and photovoltaic tracking) applications were tested and evaluated at the National Solar Thermal Test Facility in Albuquerque, New Mexico from 1986 to 1992. These heliostats have collection areas of 148 and 200 m{sup 2} and represent low-cost designs for heliostats that employ glass-metal mirrors. The evaluation encompassed the performance and operational characteristics of the heliostats, and examined heliostat beam quality, the effect of elevated winds on beam quality, heliostat drives and controls, mirror module reflectance and durability, and the overall operational and maintenance characteristics of the two heliostats. A comprehensive presentation of the results of these and other tests is presented. The results are prefaced by a review of the development (in the United States) of heliostat technology.
Shipping containers for radioactive materials must be qualified to meet a thermal accident environment specified in regulations, such at Title 10, Code of Federal Regulations, Part 71. Aimed primarily at the shipping container design, this report discusses the thermal testing options available for meeting the regulatory requirements, and states the advantages and disadvantages of each approach. The principal options considered are testing with radiant heat, furnaces, and open pool fires. The report also identifies some of the facilities available and current contacts. Finally, the report makes some recommendations on the appropriate use of these different testing methods.
Within the Yucca Mountain Site Characterization Project, the design of drifts and ramps and evaluation of the impacts of thermomechanical loading of the host rock requires definition of the rock mass mechanical properties. Ramps and exploratory drifts will intersect both welded and nonwelded tuffs with varying abundance of fractures. The rock mass mechanical properties are dependent on the intact rock properties and the fracture joint characteristics. An understanding of the effects of fractures on the mechanical properties of the rock mass begins with a detailed description of the fracture spatial location and abundance, and includes a description of their physical characteristics. This report presents a description of the abundance, orientation, and physical characteristics of fractures and the Rock Quality Designation in the thermomechanical stratigraphic units at the Yucca Mountain site. Data was reviewed from existing sources and used to develop descriptions for each unit. The product of this report is a data set of the best available information on the fracture characteristics.
In this paper we consider the problem of interprocessor communication on a Completely Connected Optical Communication Parallel Computer (OCPC). The particular problem we study is that of realizing an h-relation. In this problem, each processor has at most h messages to send and at most h messages to receive. It is clear that any 1-relation can be realized in one communication step on an OCPC. However, the best known p-processor OCPC algorithm for realizing an arbitrary h-relation for h > 1 requires {Theta}(h + log p) expected communication steps. (This algorithm is due to Valiant and is based on earlier work of Anderson and Miller.) Valiant`s algorithm is optimal only for h = {Omega}(log p) and it is an open question of Gereb-Graus and Tsantilas whether there is a faster algorithm for h = o(log p). In this paper we answer this question in the affirmative by presenting a {Theta} (h + log log p) communication step algorithm that realizes an arbitrary h-relation on a p-processor OCPC. We show that if h {le} log p then the failure probability can be made as small as p{sup -{alpha}} for any positive constant {alpha}.
This cautionary paper reminds users of quartz shock stress gauges that sensors that ignore the design rules of the Sandia quartz gauge'' may produce substantial and unrecognized deviations from normal sensitivity, waveform distortion, and anomalous conduction. Each deviant design must be extensively characterized. The consequence of non-standard gauge designs, like the shorted quartz gauge'' designs, are given for prompt response to pulsed radiation while stressed.
Through the Dish-Stirling Joint Venture Program (JVP) sponsored by the US Department of Energy (DOE), Cummins Power Generation, Inc., (CPG) and Sandia National Laboratories (SNL) have entered into a joint venture to develop and commercialize economically competitive dish-Stirling systems for remote power applications. The $14 million JVP is being conducted in three phases over a 3 1/2-year period in accordance with the Cummins Total Quality System (TQS) for new product development. The JVP is being funded equally by CPG, including its industrial partners, and the DOE. In June 1992, a concept validation'' (prototype) 5-kW[sub e], dish-Stirling system became operational at the CPG test site m Abilene, TX. And on January 1, 1993, the program advanced to phase 2. On the basis of the performance of the 5-kW[sub e] system, a decision was made to increase the rated system output to 7.5-kW[sub e]. The CPG system uses advanced components that have the potential for low cost and reliable operation, but which also have technical risks. In this paper, the status of the advanced components and results from system integration testing are presented and discussed. Performance results from system testing of the 5-kW[sub e] prototype along with phase 2 goals for the 7.5-kW[sub e] system are also discussed.
This paper presents data compiled by the Photovoltaic Design Assistance Center at Sandia National Laboratories from more than eighty field tests performed at over thirty-five photovoltaic systems in the United States during the last ten years. The recorded performance histories, failure rates, and degradation of post-Block IV modules and balance-of-system (BOS) components are described in detail.
Images taken with a synthetic aperture radar (SAR) on an airplane were distorted with phase errors generated by a computer program that simulates the propagation of radar waves through the disturbed ionosphere. The simulation is for an orbiting SAR imaging a scene on the ground. Both the spatially-invariant (decorrelation length projected onto the ground much larger than the scene size) and spatially-variant (decorrelation length much smaller than the scene size) cases are described. The spatially-invariant phase errors can be removed using several different algorithms. Problems and strategies in restoring SAR images distorted with spatially-variant phase errors are discussed.
PVDF piezoelectric polymer shock stress sensors have been used to measure the shock and impulse generated by soft X-rays and by filter debris in the SATURN Plasma Radiation Source at Sandia National Laboratories, NM. SATURN was used to generate 30 to 40 kJ, 20-ns duration, line radiation at 2 to 3 keV. Fluence on samples was nominally 40, 200, and 400 kJ/m[sup 2] (1, 5, and 10 cal/cm[sup 2]). Measurements of X-ray induced material shock response exposing both aluminum and PMMA acrylic samples agree well with companion measurements made with single crystal X-cut quartz gauges. Time-of-flight, stress, and impulse produced by Kimfol (polycarbonate/aluminum) filter debris were also measured with the PVDF gauges.
Drilling production-size holes for geothermal exploration puts a large expense at the beginning of the project, and thus requires a long period of debt service before those costs can be recaptured from power sales. If a reservoir can be adequately defined and proved by drilling smaller, cheaper slim-holes, production well drilling can be delayed until the power plant is under construction, saving years of interest payments. In the broadest terms, this project's objective is to demonstrate that a geothermal resevoir can be identified and evaluated with data collected in slim holes. We have assembled a coordinated working group, including personnel from Sandia, Lawrence Berkeley Lab, University of Utah Research Institute, US Geological Survey, independent consultants, and geothermal operators, to focus on the development of this project. This group is involved to a greater or lesser extent in all decisions affecting the direction of the research. Specific tasks being pursued include: Correlation of fluid flow and injection tests between slim-holes and production size wells. Transfer of slim-hole exploration drilling and reservoir assessment to industry so that slim-hole drilling becomes an accepted method for geothermal exploration.Development and validation of a coupled wellbore-reservoir flow simulator which can be used for reservoir evaluation from slim-hole flow data. Collection of applicable data from commercial wells in existing geothermal fields. Drilling of at least one new slim-hole and use it to evaluate a geothermal reservoir.
PVDF shock stress sensors were subjected to X-ray deposition at nominal absorbed levels of 1, 1[1/2], 3, and 5 cal/gm (SiO[sub 2] equiv.) and to neutron fluence above 10[sup 13] n/cm[sup 2] while stressed at a peak level of about 2 GPa. Moderate transitory electrical noise that occurred briefly during the radiation did not persist. PVDF shock sensors with aluminum electrodes appear satisfactory for measurement within these exposure limits. Reference quartz gauges were severely affected.