START-3 was a test program conducted in order to demonstrate and characterize the operational performance of the prototype Integrated Solar Upper Stage (ISUS) thermionic power system. The test device consisted of a graphite thermal storage uni~ multilayer foil insulation, and sixteen thermionic converters electrically connected in a series array. Several thermal input conditions were achieved during the test, which resulted in measuring converter performance at average converter hot shoe temperatures in the range of 1600 K to 2000 K. Results indicate that the ;hermionic converter; did not perform as weil as expected in the array individual sixteen converters is currently being performed.
A new method for diffusion coefficient measurement applicable to micro-fluidics is pre- sented. The method Iltilizes an analytical model describing laminar dispersion in rect- anglllar ~llicro_channe]s. The Illethod ~vas verified throllgh measllremen~ of fllloresceill diffusivity in water and aqueolls polymer solutions of differing concentration. The diffll- sivity of flllorescein was measlmed as 0.64 x 10-gm2/s in water, 0.49 x 10-gm2/s in the 4 gm/dl dextran solution and 0.38 x 10-9n12/s in the 8 gnl/dl dextran solution.
In this paper we consider the problem of simulating simple control laws involving large numbers of mobile robots. Such simulation can be computationally prohibitive if the number of robots is large enough, say 1 million, due to the 0(N2 ) cost of each time step. This work therefore uses hierarchical tree-based methods for calculating the control law. These tree-based approaches have O(NlogN) cost per time step, thus allowing for efficient simulation involving a large number of robots. For concreteness, a decentralized control law which involves only the distance and bearing to the closest neighbor robot will be considered. The time to calculate the control law for each robot at each time step is demonstrated to be O(logN).
Liquid, mixed, high-level radioactive waste (HLW) has been stored in 149 single-shell tanks (SSTS) located in tank farms on the U.S. Department of Energy's (DOE's) Hanford Site. The DOE is developing technologies to retrieve as much remaining HLW as technically possible prior to physically closing the tank farms. In support of the Hanford Tanks Initiative, Sandia National Laboratories has addressed the requirements for the regulatory closure of the radioactive component of any SST residue that may remain after physical closure. There is significant uncertainty about the end state of each of the 149 SSTS; that is, the nature and amount of wastes remaining in the SSTS after retrieval is uncertain. As a means of proceeding in the face of these uncertainties, this report links possible end-states with associated closure options. Requirements for disposal of HLW and low-level radioactive waste (LLW) are reviewed in detail. Incidental waste, which is radioactive waste produced incidental to the further processing of HLW, is then discussed. If the low activity waste (LAW) fraction from the further processing of HLW is determined to be incidental waste, then DOE can dispose of that incidental waste onsite without a license from the U.S. Nuclear Regulatory Commissions (NRC). The NRC has proposed three Incidental Waste Criteria for determining if a LAW fraction is incidental waste. One of the three Criteria is that the LAW fraction should not exceed the NRC's Class C limits.
Research is in progress to develop microminiature thermionic converters (MTCS) with high energy conversion efficiencies and variable operating temperatures using semiconductor integrated circuit (IC) fabrication methods. The use of IC techniques allows the fabrication of MTCS with cathode to anode spacing of several microns or less and with anode and cathode materials that will have work fimctions ranging from 1 eV to 3 eV. The small cathode to anode spacing and variable electrode work functions should allow the conversion of heat energy to relatively large current densities (up to tens of Amps/cmz) at relatively high conversion efficiencies ( 15-25%).
An operational evaluation of the Integrated Solar Upper Stage (ISUS) power management and distribution (PMAD) system was conducted as part of the Engine Ground Demonstration thermionic power system test program-- START-3. START-3 testing took place at the Baikal Test Stand, located in the University of New Mexico's Energy Conversion Research Laboratory at the New Mexico Engineering Research Institute in Albuquerque, NM. One objective of this test was to evaluate the operational performance of the lSUS PMAD system developed by the National Aeronautics and Space Administration (NASA) Lewis Research Center. Tests of the PMAD with the ISUS diode string demonstrated that the PMAD could regulate the output of an array of thermionic converters within the design requirements and couId be modified to optimize performance for diode strings of fewer than 16 diodes.
In support of the National Transportation Safety Board investigation of the TWA Flight 800 accident, a combined experimental/computational effort was conducted that focused on quarter-scale testing and simulation of the fuel-air explosion in the Boeing 747 center wing fuel tank. This report summarizes the modeling approach used at Sandia National Laboratories. In this approach approximations are introduced that capture the essential physics associated with turbulent flame propagation in multiple compartment fuel tanks. This model efficiently defines the pressure loading conditions during a jet-fuel air explosion in a fuel tank confinement. Modeling calculations compare favorably with a variety of experimental quarter-scale tests conducted in rigid confinement. The modeling describes well the overpressure history in several geometry configurations. Upon demonstrating a reasonable comparison to experimental observations, a parametric study of eight possible ignition sources is then discussed. Model calculations demonstrate that different loading conditions arise as the location of the ignition event is varied. By comparing the inferred damage and calculated impulses to that seen in the recovered tank, it maybe possible to reduce the number of likely sources. A possible extension of this work to better define tank damage includes coupling the combustion model as a pressure loading routine for structural failure analysis.
The emerging technology of pulsed intense ion beams has been shown to lead to improvements in surface characteristics such as hardness and wear resistance, as well as mechanical smoothing. We report hereon the use of this technology to systematically study improvements to three types of metal alloys - aluminum, iron, and titanium. Ion beam tieatment produces a rapid melt and resolidification (RMR) of the surface layer. In the case of a predeposited thin-fihn layer, the beam mixes this layer into the substrate, Ieading to improvements that can exceed those produced by treatment of the alloy alone, In either case, RMR results in both crystal refinement and metastable state formation in the treated surface layer not accessible by conventional alloy production. Although more characterization is needed, we have begun the process of relating these microstructural changes to the surface improvements we discuss in this report.
The purpose of this work was to explore the use of immersive technologies, such as those used in synthetic environments (commordy referred to as virtual realily, or VR), in enhancing the mesh- generation process for 3-dimensional (3D) engineering models. This work was motivated by the fact that automatic mesh generation systems are still imperfect - meshing algorithms, particularly in 3D, are sometimes unable to construct a mesh to completion, or they may produce anomalies or undesirable complexities in the resulting mesh. It is important that analysts and meshing code developers be able to study their meshes effectively in order to understand the topology and qualily of their meshes. We have implemented prototype capabilities that enable such exploration of meshes in a highly visual and intuitive manner. Since many applications are making use of increasingly large meshes, we have also investigated approaches to handle large meshes while maintaining interactive response. Ideally, it would also be possible to interact with the meshing process, allowing interactive feedback which corrects problems and/or somehow enables proper completion of the meshing process. We have implemented some functionality towards this end -- in doing so, we have explored software architectures that support such an interactive meshing process. This work has incorporated existing technologies developed at SandiaNational Laboratories, including the CUBIT mesh generation system, and the EIGEN/VR (previously known as MUSE) and FLIGHT systems, which allow applications to make use of immersive technologies and advanced human computer interfaces. 1
A bibliography has been compiled dealing with the verification and validation of computational simulations. The references listed in this bibliography are concentrated in the field of computational fluid dynamics (CFD). However, references from the following fields are also included: operations research, heat transfer, solid dynamics, software quality assurance, software accreditation, military systems, and nuclear reactor safety. This bibliography, containing 221 references, is not meant to be comprehensive. It was compiled during the last ten years in response to the author's interest and research in the methodology for verification and validation. The emphasis in the bibliography is in the following areas: philosophy of science underpinnings, development of terminology and methodology, high accuracy solutions for CFD verification, experimental datasets for CFD validation, and the statistical quantification of model validation. This bibliography should provide a starting point for individual researchers in many fields of computational simulation in science and engineering.
Bomb Detection Using Backscattered X-rays* Currently the most common method to determine the contents of a package suspected of containing an explosive device is to use transmission radiography. This technique requires that an x-ray source and film be placed on opposite sides of the package. This poses a problem if the pachge is placed so that only one side is accessible, such as against a wall. There is also a threat to persomel and property since exTlosive devices may be "booby trapped." We have developed a method to x-ray a paclage using backscattered x-rays. This procedure eliminates the use of film behind the target. All of the detection is done from the same side as the source. When an object is subjected to x-rays, some of them iare scattered back towards the source. The backscattenng of x-rays is propordoml to the atomic number (Z) of the material raised to the 4.1 power. This 24"' dependence allows us to easily distinguish between explosives, wires, timer, batteries, and other bomb components. Using transmission radiography-to image the contents of an unknown package poses some undesirable risks. The object must have an x-ray film placed on the side opposite the x-ray source; this cannot be done without moving the package if it has been placed firmly against a wall or pillar. Therefore it would be extremely usefid to be able to image the contents of a package from only one side, without ever having to disturb the package itself. where E is the energy of the incoming x-ray. The volume of x-rays absorbed is important because it is, of course, directly correlated to the intensity of x-mys that will be scattered. Most of the x-rays that scatter will do so in a genemlly forward direction; however, a small percentage do scatter in a backward direction. Figure 1 shows a diagram of the various fates of x-rays directed into an object. The package that was examined in this ex~enment was an attache case made of pressed fiberboardwith a vinyl covering. It was approxirmtely 36 cm wide by 51 cm long by 13 cm deep. The case was placed on an aluminum sheet under the x-ray source. Because of the laborato~ setup, the attache case was rastered in the y-coordinate direction, while the x-ray source mstered in the x-coordinate direction. However, for field use, the x-ray source would of course raster in both the x- and y-coordinate directions, while the object under interrogation would remain stationary and undisturbed. A mobile system for use by law enforcement agencies or bomb disposal squads needs to be portable and somewhat durable. A 300 kV x-ray source should be sufficient for the task requirements and can be mounted on a mobile system. A robotic carriage could be used to transport the x-ray source and the CCD camera to the proximity of the suspect package. The controlling and data analyzing elements of the system' could then be maintained at a &tie distance from the possible explosive. F@re 8 shows a diagram of a conceptual design of a possible system for this type of use. The use of backscattered x-rays for interrogation of packages that may contain explosive devices has been shown to be feasible inthelaboratory. Usinga 150kVx-ray source anddetectors consisting of plastic scintillating material, all bomb components including the wiring were detectable. However, at this time the process requires more time than is desirable for the situations in which it will most likely be needed. Further development of the technology using CCD cameras, rather than the plastic stint illator detectors, shows promise of leading to a much faster system, as well as one with better resolution. Mounting the x- ray source and the CCD camera on a robotic vehicle while keeping the controlling and analyzing components and the opemting personnel a safe distance away from the suspect package will allow such a package to be examined at low risk to human life.
The ATM Forum UNI 4.0 Security Addendum has undergone 4 revisions and has been without substantive modifications for 3 ATM Forurn meetings. This contribution is intended to assist the ATM Forum CS Working Group in the process of bringing BTD-CS-UNI-SEC-O1 .04 DIUFT to Straw Ballot. This effort applies equally to its companion documen~ BTD-CS-PNNI-SEC-O 1.02 DRAFT. BTD-CS-UNI-SEC-01 .04 DRAFT is an addendum to UNI 4.0 Signaling that describes the additional procedures needed of ATM signaling to support the signaling-based securily message exchange protocol, and its 4 basic security mechanisms, authentication, confidentiality, integrity and access control for ATM VC/VPs. These services are specified in detail in ATM Forurn document af-sec-0100.000, which is currently in Final Ballot. The remaining identified work for BTD-CS-UNI-SEC-01 .04 DRAFT includes the resolution of the TBD items in the draft, and a review of the sections of the ATM Forum Security Specification V 1.0 af-sec- 0100.000, that are specifically referenced by BTD-CS-UNI-SEC-O 1.04 DRAFT. In support of this effort, this contribution includes the relevant baseline text of the referenced sections of that Security Specification.
This contribution proposes a 128 bit wide interface structure clocked at approximately 80 MHz that will operate at 10 Gbps as a strawman for a 0C192C Utopia Specification. In addition, the concept of scalable width of data transfers in order to maintain manageably low clock rates is proposed.
The ADROIT Analysis of Dispersal Risk Qccurring in transportation code is the primary tool used to perform probabilistic risk assessments for the Transportation Safeguards Division of the Department of Energy. The current version of ADROIT uses a Pasquill-Gifford stability-class approach to meteorological characterization. In order to assess the affect that this simplified approach to weather characterization has on ADROIT'S predictions of consequence and risk, the Pasquill-Gifford stability-class approach was replaced with a direct use of radiosonde data from the National Climatic Data Center (NCDC). A comparison of results obtained for the two weather characterizations shows that, under certain circumstances, the use of the stability-class approach can result in a significant underprediction of consequence and risk values. Since such an underprediction is non-consewative, it is recommended that the stability-class approach currently used by ADROIT be replaced with a more detailed characterization of meteorological conditions. Specifically, the NCDC database was found to have sufllcient temporal and spatial resolution for ADROIT applications. Understanding that an attempt to use of all of the NCDC data in ADROIT would be prohibitive, a sampling scheme is presented as a viable alternative for instituting the recommendation of this study.
This investigation is concerned with the accuracy of numerical schemes for solving partial differential equations used in science and engineering simulation codes. Richardson extrapolation methods for steady and unsteady problems with structured meshes are presented as part of the verification procedure to determine code and calculation accuracy. The local truncation error de- termination of a numerical difference scheme is shown to be a significant component of the veri- fication procedure as it determines the consistency of the numerical scheme, the order of the numerical scheme, and the restrictions on the mesh variation with a non-uniform mesh. Genera- tion of a series of co-located, refined meshes with the appropriate variation of mesh cell size is in- vestigated and is another important component of the verification procedure. The importance of mesh refinement studies is shown to be more significant than just a procedure to determine solu- tion accuracy. It is suggested that mesh refinement techniques can be developed to determine con- sistency of numerical schemes and to determine if governing equations are well posed. The present investigation provides further insight into the conditions and procedures required to effec- tively use Richardson extrapolation with mesh refinement studies to achieve confidence that sim- ulation codes are producing accurate numerical solutions.
The Department of Energy (DOE) has developed the Waste Isolation Pilot Plant (WIPP) for the purpose of demonstrating safe management, storage, and disposal of radioactive transuranic (TRU) waste generated by U.S. defense programs. The WIPP is located in southeastern New Mexico, and the underground facilities of the WIPP (i.e., experimental rooms, disposal rooms, etc.) are sited in the bedded salt of the Salado Formation at a depth of about 660 meters. The DOE has authorized the continuance of scientific research and engineering analysis related to the performance of the WIPP repository. One area of additional research relates to characterization of the mechanical and hydrological properties of anhydrite interbeds within the Salado Formation. These anhydrite interbeds have been penetrated by the shafts that provide access to the underground facilities and also lie in close proximity to the proposed radioactive waste disposal rooms at the repository horizon. Properties of particular interest are mechanical strength, deforrnational behavior, and fluid transport properties such as permeability. These properties will be used in calculationskmalyses of the mechanical and hydrological behavior of the anhydrite, in particular, and the shaft sealing system and disposal rooms, in general.
This paper outlines the results of a cooperative effort between Sandia National Laboratories, Associated Power Analysts, Inc. and Texas A&M University to characterize the impact of a changing regulatory environment on the reliability of customer electrical service. It was desired to assess the impact in as realistic an environment as possible. Due the availability of data the initial study centered on the electric power grid in Texas. Specifically, data from the Electric Reliability Council of Texas (ERCOT) for the 1997 operational year was used in the research. Based on geography and location of generation and transmission lines, ten basic areas were considered and each area was modeled as a single point generation and load. A number of restructuring scenarios were developed by researchers at Sandia National Laboratories and investigated by Associated Power Analysts using their N-Area Reliability Program (NARP). The present study is limited to an assessment of the adequacy aspects of reliability: sufficiency of installed generation and transmission capacity to satisfy the needs of all consumers in a steady- state sense. The results are, on one hand conservative in that they address on] y the impact of peak loading. Alternatively, the~ are optimistic in that the transmission lines are assumed to be in continuous operation. The major results of this study indicate that, in anew regulatory era, the reliability of customer service will be significantly impacted, possibly in a negative fashion, unless the effects of the ensuing economic pressures are understood and appropriate actions taken.
Distributed systems have been studied for twenty years and are now coming into wider use as fast networks and powerful workstations become more readily available. In many respects a massively parallel computer resembles a network of workstations and it is tempting to port a distributed operating system to such a machine. However, there are significant differences between these two environments and a parallel operating system is needed to get the best performance out of a massively parallel system. This report characterizes the differences between distributed systems, networks of workstations, and massively parallel systems and analyzes the impact of these differences on operating system design. In the second part of the report, we introduce Puma, an operating system specifically developed for massively parallel systems. We describe Puma portals, the basic building blocks for message passing paradigms implemented on top of Puma, and show how the differences observed in the first part of the report have influenced the design and implementation of Puma.
Sandia's entry into utilizing clusters of networked workstations is called Computational Plant or CPlant for short. The design of CPlant uses Ethernet to boot the individual nodes, Myrinet to communicate within a node cluster, and ATM to connect between remote clusters. This SAND document covers the work done to enable the use of ATM on the CPlant nodes in the Fall of 1997.
This report reviews the history, theory and mathematics of wavelet analysis. Examination of the Fourier Transform and Short-time Fourier Transform methods provides tiormation about the evolution of the wavelet analysis technique. This overview is intended to provide readers with a basic understanding of wavelet analysis, define common wavelet terminology and describe wavelet amdysis algorithms. The most common algorithms for performing efficient, discrete wavelet transforms for signal analysis and inverse discrete wavelet transforms for signal reconstruction are presented. This report is intended to be approachable by non- mathematicians, although a basic understanding of engineering mathematics is necessary.
There have existed for some time relatively sparse creep databases for a number of domal salts. Although all of these data were analyzed at the time they were reported, to date there has not been a comprehensive, overall evaluation within the same analysis framework. Such an evaluation may prove of value. The analysis methodology is based on the Multimechanism Deformation (M-D) description of salt creep and the corresponding model parameters determined from conventional creep tests. The constitutive model of creep wss formulated through application of principles involved in micromechanical modeling. It was possible, at minimum, to obtain the steady state parameters of the creep model from the data on the domal salts. When this was done, the creep of the domal salts, as compared to the well-defined Waste Isolation Pilot Plant (WIPP) bedded clean salt, was either essentially identical to, or significantly harder (more creep resistant) than WIPP salt. Interestingly, the domal salts form two distinct groups, either sofl or hard, where the difference is roughly a factor often in creep rate between the twcl groups. As might be expected, this classification corresponds quite well to the differences in magnitude of effective creep volume losses of the Strategic Petroleum Reserve (SPR) caverns as determined by the CAVEMAN cavern pressure history analysis, depending upon the specific dome or region within the dome. Creep response shoulcl also correlate to interior cavern conditions that produce salt falls. WMle, in general, the caverns in hard sah have a noticeably greater propensity for salt falls, a smaller number of similar events are exhibited even in the caverns in soft salt.
This white paper presents the initial requirements for developing a new computer model for simulating the effects of extreme acts of terrorism in the United States. General characteristics of the model are proposed and the level of effort to prepare a complete written description of the model, prior to coding, is detailed. The model would simulate the decision processes and interactions of complex U. S. systems engaged in responding to and recovering from four types of terrorist incidents. The incident scenarios span the space of extreme acts of terrorism that have the potential to affect not only the impacted area, but also the entire nation. The model would be useful to decision-makers in assessing and analyzing the vulnerability of the nation's complex infrastructures, in prioritizing resources to reduce risk, and in planning strategies for immediate response and for subsequent recovery from terrorist incidents.
The Campus Executive Program sponsored this research at Cornell University. The research was directed toward the implementation of laser-based diagnostics for wire-array Z-pinches. Under this contract we were able to carry out all the necessary preparations to setup the laser diagnostics to complement our x-ray backlighting measurements of the early phase of exploding wire z-pinch plasma formation.