Publications

This project will provide scientific understanding needed to design, optimize, and calibrate the next generations of off-road diesel engines that comply with increasingly stringent pollutant emission regulations while achieving thermal efficiencies exceeding 50%.

The need to reduce the carbon footprint from medium- and heavy-duty diesel engines is clear; low-carbon biofuels are a powerful means to achieve this. Liquid fuels are rapidly deployed because existing infrastructure can be utilized for their production, transport, and distribution. Their impact is unique as they can decrease the greenhouse gas (GHG) emissions of existing vehicles and in applications resistant to electrification. However, introducing new diesel-like bio-blends into the market is very challenging. At a minimum, it requires a comprehensive understanding of the life-cycle GHG emissions of the fuels, the implications for refinery optimization and economics, the fuel’s impact on the infrastructure, the effect on the combustion performance of current and future vehicle fleets, and finally the implications for exhaust aftertreatment systems and compliance with emissions regulations. Such understanding is sought within the Co-Optima project.

Abstract not provided.

Abstract not provided.

Compliance with future ultra-low nitrogen oxide regulations with diesel engines requires the fastest possible heating of the exhaust aftertreatment system to its proper operating temperature upon cold starting. Late post injections are commonly integrated into catalyst-heating operating strategies. This experimental study provides insight into the complex interactions between the injection-strategy calibration and the tradeoffs between exhaust heat and pollutant emissions. Experiments are performed with certification diesel fuel and blends of diesel fuel with butylal and hexyl hexanoate. Further analyses of experimental data provide insight into fuel reactivity and oxygen content as potential enablers for improved catalyst-heating operation. A statistical design-of-experiments approach is developed to investigate a wide range of injection strategy calibrations at three different intake dilution levels. Thermodynamic and exhaust emissions measurements are taken using a new medium-duty, single-cylinder research engine. Analysis of the results provides insight into the effects of exhaust gas recirculation, oxygenated fuel blends, and fuel reactivity on exhaust heat and pollutant emissions. Late-cycle heat release is an important factor in determining exhaust temperatures. Intake dilution and fuel properties certainly affect late-cycle heat release, but the methods applied in this work are not sufficient to reproduce or explain the mechanisms by which improved fuel cetane rating promotes operation with hotter exhaust and lower pollutant emissions.

Abstract not provided.

Abstract not provided.

The Co-Optimization of Fuels and Engines (Co-Optima) initiative from the US Department of Energy aims to co-develop fuels and engines in an effort to maximize energy efficiency and the utilization of renewable fuels. Many of these renewable fuel options have fuel chemistries that are different from those of petroleum-derived fuels. Because practical market fuels need to meet specific fuel-property requirements, a chemistry-agnostic approach to assessing the potential benefits of candidate fuels was developed using the Central Fuel Property Hypothesis (CFPH). The CFPH states that fuel properties are predictive of the performance of the fuel, regardless of the fuel's chemical composition. In order to use this hypothesis to assess the potential of fuel candidates to increase efficiency in spark-ignition (SI) engines, the individual contributions towards efficiency potential in an optimized engine must be quantified in a way that allows the individual fuel properties to be traded off for one another. This review article begins by providing an overview of the historical linkages between fuel properties and engine efficiency, including the two dominant pathways currently being used by vehicle manufacturers to reduce fuel consumption. Then, a thermodynamic-based assessment to quantify how six individual fuel properties can affect efficiency in SI engines is performed: research octane number, octane sensitivity, latent heat of vaporization, laminar flame speed, particulate matter index, and catalyst light-off temperature. The relative effects of each of these fuel properties is combined into a unified merit function that is capable of assessing the fuel property-based efficiency potential of fuels with conventional and unconventional compositions.

Most multidimensional engine simulations spend much time solving for non-equilibrium spray dynamics (atomization, collision, vaporization). However, their accuracy is limited by significant grid dependency, and the need for extensive calibration. This is critical for modeling cold-start diesel fuel post injections, which occur at low temperatures and pressures, far from typical model validation ranges. At the same time, resolving micron-scale spray phenomena would render full Eulerian multiphase calculations prohibitive. In this study, an improved phase equilibrium based approach was implemented and assessed for simulating diesel catalyst heating operation strategies. A phase equilibrium solver based on the model by Yue and Reitz [1] was implemented: a fully multiphase CFD solver is employed with an engineering-size engine grid, and fuel injection is modeled using the standard Lagrangian parcels approach. Mass and energy from the liquid parcels are released to the Eulerian multiphase mixture according to an equilibrium-based liquid jet model. An improved phase equilibrium solver was developed to handle large real-gas mixtures such as those from accurate chemical kinetics mechanisms. The liquid-jet model was improved such that momentum transfer to the Eulerian solver better reproduces the physical spray jet structure. Validation of liquid/vapor penetration predictions showed that the model yields accurate results with very limited tuning and low sensitivity to the few calibration constants. In-cylinder simulations of diesel catalyst heating operation strategies showed that capturing spray structure is paramount when short, transient injection pulses and low temperatures are present. Furthermore, the EP model provides improved predictions of post-injection spray structure and ignitability, while conventional spray modeling does not capture the increase of liquid penetration during the expansion stroke. Finally, the only important EP model calibration constant, Cliq, does not affect momentum transfer, but it changes the local charge cooling distribution through the local energy transfer, which makes it candidate to additional research. The results confirm that non-equilibrium spray processes do not need to be resolved in engineering simulations of high-pressure diesel sprays.

Abstract not provided.

Fuel injection rate laws are one of the most important pieces of information needed when modeling engine combustion with computational fluid dynamics. In this study, a simple phenomenological model of a common-rail injector was developed and calibrated for the Bosch CRI2.2 platform. The model requires three tunable parameter fits, making it relatively easy to calibrate and suitable for injector modeling when high-fidelity information about the internal injector’s geometry and electrical circuit details are not available. Each injection pulse is modeled as a sequence of up to four stages: an injection needle mechanical opening transient, a full-lift viscous flow inertial transient, a Bernoulli steady-state stage, and a needle descent transient. Parameters for each stage are obtained as polynomial fits from measured injection rate properties. The model enforces total injected mass, and the intermediate stages are only introduced if the injection pulse duration is long enough. Experimental rates of injection from two separate campaigns on the same injector were used to calibrate the model. The model was first validated against measured injection rate laws featuring pilot injections, short partially premixed combustion pulses, and conventional diesel combustion injection strategies. Then, it was employed as an input to engine computational fluid dynamics simulations, which were run to simulate experiments of mixture formation in an optically accessible light-duty diesel engine. It was found that, though simple, this model is capable of predicting both pilot and main injection pulse mass flow rates well: the simulations yielded accurate predictions of in-cylinder equivalence ratio distributions from injection strategies for both partially premixed combustion and pilot injections. Also, once calibrated, the model produced appropriate results for a wide range of injected mass and rail pressure values. Finally, it was observed that usage of such a relatively simple model can be a good choice when high-fidelity injection rate input and highly detailed information of the injector’s geometry and operation are not available, particularly as noticeable discrepancies can be present also among different experimental campaigns on similar hardware.

Lagrangian spray modeling represents a critical boundary condition for multidimensional simulations of in-cylinder flow structure, mixture formation and combustion in internal combustion engines. Segregated models for injection, breakup, collision and vaporization are usually employed to pass appropriate momentum, mass, and energy source terms to the gas-phase solver. Careful calibration of each sub-model generally produces appropriate results. Yet, the predictiveness of this modeling approach has been questioned by recent experimental observations, which showed that at trans- A nd super-critical conditions relevant to diesel injection, classical atomization and vaporization behavior is replaced by a mixing-controlled phase transition process of a dense fluid. In this work, we assessed the shortcomings of classical spray modeling with respect to real-gas and phase-change behavior, employing a multicomponent phase equilibrium solver and liquid-jet theory. A Peng-Robinson Equation of State (PR-EoS) model was implemented, and EoS-neutral thermodynamics derivatives were introduced in the FRESCO CFD platform turbulent NS solver. A phase equilibrium solver based on Gibbs free energy minimization was implemented to test phase stability and to compute phase equilibrium. Zero-dimensional flash calculations were employed to validate the solver with single- A nd multi-component fuels, at conditions relevant to diesel injection. The validation showed that 2-phase mixture temperature in the jet core can deviate up to 40K from the single-phase solution. Surface equilibrium with Raoult's law employed for drop vaporization calculation was observed to deviate up to 100% from the actual multiphase real-gas behavior. Liquid-jet spray structure in high pressure fuel injection CFD calculations was modeled using an equilibrium-phase (EP) Lagrangian injection model, where liquid fuel mass is released to the Eulerian liquid phase, assuming phase-equilibrium in every cell. Comparison to state-of-the-art modeling featuring KH-RT breakup and multicomponent fuel vaporization highlighted the superior predictive capabilities of the EP model in capturing liquid spray structure at several conditions with limited calibration efforts.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Stepped-lip diesel pistons can enhance in-cylinder vortex formation and thereby improve the thermal efficiency and emissions behavior of a diesel engine. Further improvements to diesel combustion systems may be realized through improved understanding of the mechanisms by which fuel sprays interact with pistons to form vortices. Analysis of computational fluid dynamics simulations provides insight about vorticity formation in one particular region of a particular stepped-lip combustion chamber. Interactions at the boundary between the sprays and the piston surface are a source of new vorticity that is transported upward and outward. This process is believed to be the origin of an energetic vortex that has been experimentally observed in the outermost region of the combustion chamber during the mixing-controlled combustion process, and is associated with improved turbulent mixing.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Diesel engines remain a cost-effective, efficient, powerful propulsion source for many light- and medium-duty vehicle applications. Modest efficiency improvements in these engines can eliminate millions of tons of CO₂ emissions per year, but these improvements will require improved understanding of how diesel combustion chamber geometry influences mixture preparation, combustion, and pollutant formation processes. The research focus for this performance period is to provide insight into spray-wall interactions in stepped-lip combustion chambers. These interactions are believed to promote the formation of recirculating flow structures that improve thermal efficiency and reduce soot emissions, but these benefits are only fully realized for late main injection timings. A detailed mechanistic understanding of these processes can lead to cleaner, more efficient combustion chamber designs. This project will provide scientific understanding needed to design, optimize, and calibrate the next generations of light- and medium-duty diesel engines that comply with increasingly stringent pollutant emission regulations while achieving thermal efficiencies approaching 50%.

Faster combustion improves the efficiency of a diesel engine, and in medium-duty diesel engines, interactions between the fuel sprays and the piston bowl walls play a key role in determining heat-release rates. Stepped-lip pistons can promote the formation of vortices that are correlated with faster, more efficient heat-release, but this behavior is primarily observed for late injection timings at which the engine is not operating at its peak efficiency. The objectives of this part of the project are to explain the physical mechanisms responsible for this phenomenon, to identify measures that may enhance vortex formation, and to quantify the extent to which these measures may improve the engine's thermal efficiency.

In light-duty direct-injection (DI) diesel engines, combustion chamber geometry influences the complex interactions between swirl and squish flows, spray-wall interactions, as well as late-cycle mixing. Because of these interactions, piston bowl geometry significantly affects fuel efficiency and emissions behavior. However, due to lack of reliable in-cylinder measurements, the mechanisms responsible for piston-induced changes in engine behavior are not well understood. Non-intrusive, in situ optical measurement techniques are necessary to provide a deeper understanding of the piston geometry effect on in-cylinder processes and to assist in the development of predictive engine simulation models. This study compares two substantially different piston bowls with geometries representative of existing technology: a conventional re-entrant bowl and a stepped-lip bowl. Both pistons are tested in a single-cylinder optical diesel engine under identical boundary conditions. Utilizing high-speed soot natural luminosity (NL) imaging, 20 kHz time-resolved combustion image velocimetry (CIV) technique is developed to quantify the macro-scale motions of soot clouds during the mixing-controlled portion of combustion. Under a part-load conventional combustion regime, CIV-resolved swirl ratio and the tumble-plane projection of velocity fields confirm that the injection-induced redistribution of angular momentum, rather than squish/reverse squish flow, is a dominant source for swirl amplification between two piston geometries. A strong connection has been found between the CIV-resolved combusting flow structure and its succeeding enhanced late-stage burn rate. With SOI main shortly after TDC, combustion in stepped-lip piston exhibits shorter late-burn duration (CA50-CA90) and faster burn rate compared to re-entrant piston. In the same boundary condition, a unique combusting flow structure is observed with CIV in the stepped-lip piston: a long-lasting flow structure with opposing radial velocity directions between the squish region and stepped-lip region. Interestingly, this flow structure is never optically observed with the re-entrant piston. The best hypothesis is that there exists a long-lasting vertical toroidal vortex on the shoulder of stepped-lip piston crown near CA50. A phenomenological model is proposed to provide a partial, but valuable picture of late-stage combusting flow structure which is a key to understand how piston bowl geometry can influence thermal efficiency for swirl-supported diesel engines.

Abstract not provided.

Abstract not provided.

In light- and medium-duty diesel engines, piston bowl shape influences thermal efficiency, either due to changes in wall heat loss or to changes in the heat release rate. The relative contributions of these two factors are not clearly described in the literature. In this work, two production piston bowls are adapted for use in a single cylinder research engine: a conventional, re-entrant piston, and a stepped-lip piston. An injection timing sweep is performed at constant load with each piston, and heat release analyses provide information about thermal efficiency, wall heat loss, and the degree of constant volume combustion. Zero-dimensional thermodynamic simulations provide further insight and support for the experimental results. The effect of bowl geometry on wall heat loss depends on injection timing, but changes in wall heat loss cannot explain changes in efficiency. Late cycle heat release is faster with the stepped-lip bowl than with the conventional re-entrant bowl, which leads to a higher degree of constant volume combustion and therefore higher thermal efficiency. This effect also depends on injection timing. In general, increasing the degree of constant volume combustion is significantly more effective at improving thermal efficiency than decreasing wall heat loss. Maximizing thermal efficiency will require a deeper understanding of how bowl geometry impacts flow structure, turbulent mixing, and mixing-controlled combustion.

Diesel piston bowl geometry can affect turbulent mixing and therefore it impacts heat-release rates, thermal efficiency, and soot emissions. The focus of this work is on the effects of bowl geometry and injection timing on turbulent flow structure. This computational study compares engine behavior with two pistons representing competing approaches to combustion chamber design: a conventional, re-entrant piston bowl and a stepped-lip piston bowl. Three-dimensional computational fluid dynamics (CFD) simulations are performed for a part-load, conventional diesel combustion operating point with a pilot-main injection strategy under non-combusting conditions. Two injection timings are simulated based on experimental findings: an injection timing for which the stepped-lip piston enables significant efficiency and emissions benefits, and an injection timing with diminished benefits compared to the conventional, re-entrant piston. While the flow structure in the conventional, re-entrant combustion chamber is dominated by a single toroidal vortex, the turbulent flow evolution in the stepped-lip combustion chamber depends more strongly on main injection timing. For the injection timing at which faster mixing controlled heat release and reduced soot emissions have been observed experimentally, the simulation predicts the formation of two additional recirculation zones created by interactions with the stepped-lip. Analysis of the CFD results reveals the mechanisms responsible for these recirculating flow structures. Vertical convection of outward radial momentum drives the formation of the recirculation zone in the squish region, while adverse pressure gradients drive flow inward near the cylinder head, thereby contributing to the formation of the second recirculation zone above the step. Bulk gas density is higher for the near-TDC injection timing than for the later injection timing. This leads to increased air entrainment into the sprays and slower spray velocities, so the sprays take longer to interact with the step, and beneficial recirculating flow structures are not obseved.

Abstract not provided.

Despite compliance issues in previous years, automakers have demonstrated that the newest generation of diesel power trains are capable of meeting all federal and state regulations (EPA, 2016). Diesels continue to be a cost-effective, efficient, powerful propulsion source for many light- and medium-duty vehicle applications (Martec, 2016). Even modest reductions in the fuel consumption of light- and medium duty diesel vehicles in the U.S. will eliminate millions of tons of CO2 emissions per year. Continued improvement of diesel combustion systems will play an important role in reducing fleet fuel consumption, but these improvements will require an unprecedented scientific understanding of how changes in engine design and calibration affect the mixture preparation, combustion, and pollutant formation processes that take place inside the cylinder. The focus of this year’s research is to provide insight into the physical mechanisms responsible for improved thermal efficiency observed with a stepped-lip piston. Understanding how piston design can influence efficiency will help engineers develop and optimize new diesel combustion systems.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

In-cylinder flow measurements are necessary to gain a fundamental understanding of swirl-supported, light-duty Diesel engine processes for high thermal efficiency and low emissions. Planar particle image velocimetry (PIV) can be used for non-intrusive, in situ measurement of swirl-plane velocity fields through a transparent piston. In order to keep the flow unchanged from all-metal engine operation, the geometry of the transparent piston must adapt the production-intent metal piston geometry. As a result, a temporally- and spatially-variant optical distortion is introduced to the particle images. To ensure reliable measurement of particle displacements, this work documents a systematic exploration of optical distortion quantification and a hybrid back-projection procedure that combines ray-tracing-based geometric and in situ manual back-projection approaches. The proposed hybrid back-projection method for the first time provides a time-efficient and robust way to process planar PIV measurements conducted in an optical research engine with temporally- and spatially-varying optical distortion. This method is based upon geometric ray tracing and serves as a universal tool for the correction of optical distortion with an arbitrary but axisymmetric piston crown window geometry. Analytical analysis demonstrates that the ignorance of optical distortion change during the PIV laser temporal interval may induce a significant error in instantaneous velocity measurements. With the proposed digital dewarping method, this piston-motion-induced error can be eliminated. Uncertainty analysis with simulated particle images provides guidance on whether to back-project particle images or back-project velocity fields in order to minimize dewarping-induced uncertainties. The optimal implementation is piston-geometry-dependent. For regions with significant change in nominal magnification factor, it is recommended to apply the proposed back-projection approach to particle images prior to PIV interrogation. For regions with significant dewarping-induced particle elongation (Ep > 3), it is recommended to apply the proposed dewarping method to the vector fields resulting from PIV interrogation of raw particle image pairs.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

A Moehwald HDA (HDA is a German acronym: Hydraulischer Druckanstieg: hydraulic pressure increase) injection quantity and rate measuring unit is used to investigate injection rates obtained with a fast-acting, preproduction diesel solenoid injector. Experimental parametric variations are performed to determine their impact on measured injection rate traces. A pilot-main injection strategy is investigated for various dwell times; these preproduction injectors can operate with very short dwell times with distinct pilot and main injection events. Dwell influences the main injection rate shape. A comparison between a diesel-like fuel and a gasoline-like fuel shows that injection rates are comparable for a single injection but dramatically different for multiple injections with short dwells.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Based on the ensemble-averaged velocity results, flow asymmetry characterized by the swirl center offset and the associated tilting of the vortex axis is quantified. The observed vertical tilting of swirl center axis is similar for tested swirl ratios (2.2 and 3.5), indicating that the details of the intake flows are not of primary importance to the late-compression mean flow asymmetry. Instead, the geometry of the piston pip likely impacts the flow asymmetry. The PIV results also confirm the numerically simulated flow asymmetry in the early and late compression stroke: at BDC, the swirl center is located closer to the exhaust valves for swirl-planes farther away from the fire deck; near TDC, the swirl center is located closer to the intake valves for swirl-planes farther away from the fire deck. It is evident from experimentally determined velocity fields that the transition between these two asymmetries has a different path for various swirl ratios, suggesting the influence of intake port flows. Flow field asymmetry can lead to an asymmetric mixture preparation in Diesel engines. To understand the evolution of this asymmetry, it is necessary to characterize the in-cylinder flow over the full compression stroke. Moreover, since bowl-in-piston cylinder geometries can substantially impact the in-cylinder flow, characterization of these flows requires the use of geometrically correct pistons. In this work, the flow has been visualized via a transparent piston top with a realistic bowl geometry, which causes severe experimental difficulties due to the spatial and temporal variation of the optical distortion. An advanced optical distortion correction method is described to allow reliable particle image velocimetry (PIV) measurements through the full compression stroke.

In this work computational and experimental approaches are combined to characterize in-cylinder flow structures and local flow field properties during operation of the Sandia 1.9L light-duty optical Diesel engine. A full computational model of the single-cylinder research engine was used that considers the complete intake and exhaust runners and plenums, as well as the adjustable throttling devices used in the experiments to obtain different swirl ratios. The in-cylinder flow predictions were validated against an extensive set of planar PIV measurements at different vertical locations in the combustion chamber for different swirl ratio configurations. Principal Component Analysis was used to characterize precession, tilting and eccentricity, and regional averages of the in-cylinder turbulence properties in the squish region and the piston bowl. Complete sweeps of the port throttle configurations were run to study their effects on the flow structure, together with their correlation with the swirl ratio. Significant deviations between the flows in the piston bowl and squish regions were observed. Piston bowl design, more than the swirl ratio, was identified to foster flow homogeneity between these two regions. Also, analysis of the port-induced flow showed that port geometry, more than different intake port mass flow ratios, can improve turbulence levels in-cylinder.

Abstract not provided.

Abstract not provided.

Abstract not provided.

For a pilot-main injection strategy in a single cylinder light duty diesel engine, the dwell between the pilot- and maininjection events can significantly impact combustion noise. As the solenoid energizing dwell decreases below 200 μs, combustion noise decreases by approximately 3 dB and then increases again at shorter dwells. A zero-dimensional thermodynamic model has been developed to capture the combustion-noise reduction mechanism; heat-release profiles are the primary simulation input and approximating them as top-hat shapes preserves the noise-reduction effect. A decomposition of the terms of the underlying thermodynamic equation reveals that the direct influence of heat-release on the temporal variation of cylinder-pressure is primarily responsible for the trend in combustion noise. Fourier analyses reveal the mechanism responsible for the reduction in combustion noise as a destructive interference in the frequency range between approximately 1 kHz and 3 kHz. This interference is dependent on the timing of increases in cylinder-pressure during pilot heat-release relative to those during main heat-release. The mechanism by which combustion noise is attenuated is fundamentally different from the traditional noise reduction that occurs with the use of long-dwell pilot injections, for which noise is reduced primarily by shortening the ignition delay of the main injection. Band-pass filtering of measured cylinderpressure traces provides evidence of this noise-reduction mechanism in the real engine. When this close-coupled pilot noise-reduction mechanism is active, metrics derived from cylinder-pressure such as the location of 50% heat-release, peak heat-release rates, and peak rates of pressure rise cannot be used reliably to predict trends in combustion noise. The quantity and peak value of the pilot heat-release affect the combustion noise reduction mechanism, and maximum noise reduction is achieved when the height and steepness of the pilot heat-release profile are similar to the initial rise of the main heat-release event. A variation of the initial rise-rate of the main heat-release event reveals trends in combustion noise that are the opposite of what would happen in the absence of a close-coupled pilot. The noise-reduction mechanism shown in this work may be a powerful tool to improve the tradeoffs among fuel efficiency, pollutant emissions, and combustion noise.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.