Numerous projects are looking into distributing blends of natural gas and different amounts of gaseous hydrogen through the existing natural gas distribution system, which is widely composed of medium density polyethylene (MDPE) line pipes. The mechanical behavior of MDPE with hydrogen is not well understood; therefore, the effect of gaseous H2 on the mechanical properties of MDPE needs to be examined. In the current study, we investigate the effects of gaseous H2 on fatigue life and fracture resistance of MDPE in the presence of 3.4 MPa gaseous H2. Fatigue life tests were also conducted at a pressure of 21 MPa to investigate the effect of gas pressure on the fatigue behavior of MDPE. Results showed that the presence of gaseous H2 did not degrade the fatigue life nor the fracture resistance of MDPE. Additionally, based on the value of fracture resistance calculated, a failure assessment diagram was constructed to determine the applicability of using MDPE pipeline for distribution of gaseous H2. Even in the presence of a large internal crack, the failure assessment evaluation indicated that the MDPE pipes lie within the safe region under typical service conditions of natural gas distribution pipeline system.
Austenitic stainless steels are the standard materials for containment of hydrogen and tritium because of their resistance to mechanical property degradation in those environments. The mechanical performance of the primary containment material is critical for tritium handling, processing, and storage, thus comprehensive understanding of the processes of tritium embrittlement is an enabling capability for fusion energy. This work describes the investigation of the effects of low levels of tritium-decay-helium ingrowth on 304 L tubes. Long-term aging with tritium leads to high helium contents in austenitic stainless steels and can reduce fracture toughness by 95 %, but the details of behavior at low helium contents are not as well characterized. Here, we present results from tensile testing of tritium pre-charged 304 L tube specimens with a variety of starting microstructures that all contain a low level of helium. The results of the tritium exposed-and-aged materials are compared to previously reported results on similar specimens tested in an unexposed condition as well as the hydrogen precharged condition. Tritium precharging and aging for a short duration resulted in increased yield strengths, ultimate tensile strengths and slightly increased elongation to failure, comparable to higher concentrations of hydrogen precharging.
This report serves as the proceedings of the Hydrogen Compatible Materials Workshop held virtually by Sandia National Laboratories on December 2-3, 2020. The purpose of the workshop was to assemble subject matter experts at Sandia and its national laboratory partners within the U.S. Department of Energy's (DOE) Hydrogen Materials Compatibility (H-Mat) Consortium with public and private stakeholders in the research, development and deployment of hydrogen technologies to discuss the topic of hydrogen compatible materials. This workshop was designed to build on past events and current research and development (R&D) efforts to develop a forward-looking vision that identifies gaps and challenges for the next decade. In particular, the workshop organizers sought to expand their understanding of hydrogen compatible materials needs for power, manufacturing and other industrial uses to enable deeper impact and widespread use of hydrogen while continuing to address open questions in hydrogen-powered transportation of concern to Original Equipment Manufacturers, hydrogen producers, materials & component suppliers and other private entities. The workshop was primarily organized as a series of panel-led discussions on the topics of hydrogen-enabled transportation, heating and power, and industrial uses. Each panel consisted of 2-3 subject matter experts who relayed their perspectives on a set of framing questions developed to facilitate discussion by the broader group of workshop participants. By the workshop's conclusion, the participants identified and prioritized a list of technical challenges for each panel topic where further R&D is warranted.
Austenitic stainless steels are used extensively in harsh environments, including for high-pressure gaseous hydrogen service. However, the tensile ductility of this class of materials is very sensitive to materials and environmental variables. While tensile ductility is generally insufficient to qualify a material for hydrogen service, ductility is an effective tool to explore microstructural and environmental variables and their effects on hydrogen susceptibility, to inform understanding of the mechanisms of hydrogen effects in metals, and to provide insight to microstructural variables that may improve relative performance. In this study, hydrogen precharging was used to simulate high-pressure hydrogen environments to evaluate hydrogen effects on tensile properties. Several austenitic stainless steels were considered, including both metastable and stable alloys. Room temperature and subambient temperature tensile properties were evaluated with three different internal hydrogen contents for type 304L and 316L austenitic stainless steels and one hydrogen content for XM-11. Significant ductility loss was observed for both metastable and stable alloys, suggesting the stability of the austenitic phase is not sufficient to characterize the effects of hydrogen. Internal hydrogen does influence the character of deformation, which drives local damage accumulation and ultimately fracture for both metastable and stable alloys. While a quantitative description of hydrogen-assisted fracture in austenitic stainless steels remains elusive, these observations underscore the importance of the hydrogen-defect interactions and the accumulation of damage at deformation length scales.
